Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 LCDUINO

openhardware.io last edited by

https://www.openhardware.io/view/8247/LCDUINO
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by

( Verifying that posting to this thread works. Please ignore. )
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

Testing using Firefox browser.
Reply Quote 1
1 Reply Last reply
NeverDie Hero Member last edited by

This project is missing a bill of materials. In particular, the LCD components don't appear to be named, not even on the schematic.

Also, do there exist gerber files to accompany it?
Reply Quote 0
1 Reply Last reply
Nca78 Hardware Contributor last edited by @NeverDie

@NeverDie said in LCDUINO:

the LCD components don't appear to be named, not even on the schematic

Looks like a typical text LCD like 1602 on the picture.
Reply Quote 1
1 Reply Last reply

serial 20 arduino nano 13 lcd 5 uart 4

5
Posts

74
Views

Log in to reply

Suggested Topics

Gateway not working on VeraLite + UI6 - No Serial Port configuration available
Vera • vera serial serialgateway ui6 • • cdrum

11

0
Votes

11
Posts

5980
Views

@brettzky84 said: Im using the serial gateway on u17 and have it working fine. i have the same problem as you when my vera is rebooted or powered off, but found 2 solutions. 1 with the vera on disconnect then reconnect the serial gateway. wait 10seconds refresh the dashboard page. Then go to app/ developer apps/ serial connection. Reset your baud rate to 115200??... Thansk. I ended up upgrading to the latst UI7 beta. My gateway is now working!!! Let's see how stable it is. (UI7 has fixed some of my other issue too)
Combining Serial and MQTT/Ethernet Gateway
Troubleshooting • mqtt ethernet serial • • codenea

6

0
Votes

6
Posts

3384
Views

@lafleur I abandoned it due to the fact that my Nano cannot fit it together with signing support.
Serial Gateway mystery
Troubleshooting • gateway serial • • cribben

3

0
Votes

3
Posts

1788
Views

Thanks for all the info all But still have the problem with vera3 on ui7 Cribben, I follow the instructions on the my sensor vera plugin and it comes up with ver 1.3 and no lib # how did you get the new plugin to load Any help at all would be welcome as ui7 is not too smooth yet.
💬 MDMSNode "xRoom"
OpenHardware.io • ethernet usb i2c stm32 spi uart st485 dio • • openhardware.io

1

1
Votes

1
Posts

417
Views

No one has replied
Building a gateway with two transport layers
Hardware • gateway serial rs485 rf24 wireless communication wired transport layer • • Giovanni Chiva

3

0
Votes

3
Posts

54
Views

@mfalkvidd thank you very much for your quick answer! I'll look into that.
MySensors MQTT gateway and serial rs485 sensor node communication
Development • arduino gateway mqtt serial rs485 openhab2 nodes • • ehome

3

0
Votes

3
Posts

3896
Views

Thanks for your fast reply. That sounds easy. And you think that the communication between sensor nodes and Gateway are still possible via wired RS485? I tried to find an example on this site for sending Information from Gateway to sensor nodes. (via SendMessage ?) For example I like to Switch on/off an light that is connected to an relay board at my sensor node. Communcation Flow: OpenHab2 --> MQTT --> Gateway --> RS485 --> Sensor Node --> Relay Board Currently I have an working RS485 Connection between my Arduino Uno's with the use from SoftwareSerial library. During my testings I realized, that the message that I triy to send "Hello" will be sent to the other arduino char by char. Is that true? Because I tried to raise up an pin on HIGH with "if(msg == "Hello")..." But it doesn't worked. Will the sendMsg method from the MySensor library handle this out of the box? Regards, Simon
💬 Arduino Nano NRF24L01+ Shield
OpenHardware.io • nrf24l01+ arduino nano • • openhardware.io

3

0
Votes

3
Posts

532
Views

I also have project for mini. The project have pads for battery, battery protection IC, LIPO charger USB for charging... battery voltage measurements.... But the project is not released yet, because high temperature during charging.
💬 MysX2USB
OpenHardware.io • serial usb mysx ftdi programming • • openhardware.io

14

2
Votes

14
Posts

4222
Views

@tbowmo more out of curiosity, and from someone that just got started on electronics, so please sorry if this sounds like very noob, but, would it not be safer to plug the V_TARGET LED to the +3.3v pin? How do you ensure that the resistor on the V_TARGET will have constant voltage and that will not blow from over voltage if the VCCio pin is depended on the the Motherboard power? Thank You and nice work

61
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1