Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 LCDUINO

openhardware.io last edited by

https://www.openhardware.io/view/8247/LCDUINO
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by

( Verifying that posting to this thread works. Please ignore. )
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

Testing using Firefox browser.
Reply Quote 1
1 Reply Last reply
NeverDie Hero Member last edited by

This project is missing a bill of materials. In particular, the LCD components don't appear to be named, not even on the schematic.

Also, do there exist gerber files to accompany it?
Reply Quote 0
1 Reply Last reply
Nca78 Hardware Contributor last edited by @NeverDie

@NeverDie said in LCDUINO:

the LCD components don't appear to be named, not even on the schematic

Looks like a typical text LCD like 1602 on the picture.
Reply Quote 1
1 Reply Last reply

serial 20 arduino nano 13 lcd 5 uart 4

5
Posts

74
Views

Log in to reply

Suggested Topics

MySensors MQTT gateway and serial rs485 sensor node communication
Development • arduino gateway mqtt serial rs485 openhab2 nodes • • ehome

3

0
Votes

3
Posts

3894
Views

Thanks for your fast reply. That sounds easy. And you think that the communication between sensor nodes and Gateway are still possible via wired RS485? I tried to find an example on this site for sending Information from Gateway to sensor nodes. (via SendMessage ?) For example I like to Switch on/off an light that is connected to an relay board at my sensor node. Communcation Flow: OpenHab2 --> MQTT --> Gateway --> RS485 --> Sensor Node --> Relay Board Currently I have an working RS485 Connection between my Arduino Uno's with the use from SoftwareSerial library. During my testings I realized, that the message that I triy to send "Hello" will be sent to the other arduino char by char. Is that true? Because I tried to raise up an pin on HIGH with "if(msg == "Hello")..." But it doesn't worked. Will the sendMsg method from the MySensor library handle this out of the box? Regards, Simon
PiGatewaySerial doesn't write to virtual serial device /dev/ttyMySensorsGateway
Troubleshooting • raspberry pi serial pigatewayserial tty • • Michele Rappazzo

5

0
Votes

5
Posts

2602
Views

I added the capacitor, but there's always the same problem
Building a gateway with two transport layers
Hardware • gateway serial rs485 rf24 wireless communication wired transport layer • • Giovanni Chiva

3

0
Votes

3
Posts

51
Views

@mfalkvidd thank you very much for your quick answer! I'll look into that.
💬 MysX2USB
OpenHardware.io • serial usb mysx ftdi programming • • openhardware.io

14

2
Votes

14
Posts

4222
Views

@tbowmo more out of curiosity, and from someone that just got started on electronics, so please sorry if this sounds like very noob, but, would it not be safer to plug the V_TARGET LED to the +3.3v pin? How do you ensure that the resistor on the V_TARGET will have constant voltage and that will not blow from over voltage if the VCCio pin is depended on the the Motherboard power? Thank You and nice work
serial, Ethernet to MQTT
MyController.org • mqtt ethernet serial mycontroller converter bridge • • jkandasa

5

1
Votes

5
Posts

41
Views

@Yveaux said in serial, Ethernet to MQTT: Of course, but MySensors MQTT gateway runs just as fine when connected over cabled ethernet, as when connected over wifi I do not know that Now on this tool, I do not see much benefit from ethernet to MQTT Still, it is good from serial to MQTT.
My simple and minimalistic calculator with only two buttons
My Project • arduino lcd attiny85 • • Volos Rakic

2

2
Votes

2
Posts

1119
Views

Nice work! Reminds me of this great short story by Isaac Asimov from 1958.
FTDI/Serial or USB?
Hardware • serial usb ftdi serial monitor • • Samuel235

10

0
Votes

10
Posts

3219
Views

Actually, I use the FTDI connector on my outdoor weather sensor to power it from the solar/Li-Ion charger board. Used angled headers to keep the height down. I'll try to post a picture asap.

62
Online

11.1k
Users

11.1k
Topics

112.5k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1