Array Relay Button Actuator

mikemayers

Just tested this sketch and it works. Thank for the effort.

maglo18

Could someone tell what i should to modify to use toggle button not flash button?

jeylites

@maglo18 what do you mean?

maglo18

In yours sketch state button should high next low then relay change state. I want to have possibility after button HIGH relay state change button LOW state relay change again

jemish

yes , I have same problem.

how can we use simple wall switch with relay to ON and OFF the lights.

AWI

For learning purposes: Instead of coding it for you, try the line of thought:

Now it changes with the toggle, so if "value" (switch) becomes high is changes the state of the relays, send the message to controller and stores it in EEPROM.

If you use a normal switch, you should change the state if when the "value" changes. So remember the last state of the switch and make it happen ;-)

btw :you need a variable to store the last button state and the physical position of the switch does not change if you update the relay switch from the controller..

jeylites

Just wondering any of you guys made progress in normal switch?

rainair

Hello this is my first post, but i follow my sensors for about 2 months.
Excuse my bad english.

For those how want use a normal in wall switch

just change the line:

if (value != Relays[i].oldValue && value == 0){

to

if (value != Relays[i].oldValue){

to

hope this was a bit helpfully

jeylites

@rainair, I tested it and it works! Thanks!!!

gonzalonal

@jeylites said:

Relays[i].relayState = gw.loadState(i); // retrieve last values from EEPROM
digitalWrite(Relays[i].relayPin, Relays[i].relayState? RELAY_ON:RELAY_OFF); // and set relays accordingly
gw.send(msg[i].set(Relays[i].relayState? true : false)); // make controller aware of last status
gw.present(i, S_LIGHT); // present sensor to gateway
delay(250);

It's my idea, or shouldn't the sensor be presented to the gateway before sending it status?
Thanks! regards.

jeylites

@gonzalonal

I don't think it matters. You could try flip "gw.send & gw.present" and see how it respond to the change.

ewgor

Wow ! this is what i was looking for ... Could anyone please share with us some Openhab settings for this wonderful Arduino sketch?
How can we assign in OH buttons to correspond to the physical buttons on the breadboard ?

Looking for any answer.

Thanks all!

Cliff Karlsson

How would I update this to work with 1.6?

niccodemi

@Cliff-Karlsson I recently started using 1.6 version, below is converted sketch. It works with momentary (pushbuttons) switches only.

Does anyone have sketch for toggle switches?

#define MY_RADIO_NRF24

#define MY_REPEATER_FEATURE

#include <MySensor.h>

#include <SPI.h>
#include <Bounce2.h>
#define RELAY_ON 0                      // switch around for relay HIGH/LOW state
#define RELAY_OFF 1
//

#define noRelays 2                     //2-4
const int relayPin[] = {14,15};          //  switch around pins to your desire
const int buttonPin[] = {3,4};      //  switch around pins to your desire

class Relay             // relay class, store all relevant data (equivalent to struct)
{
public:                                      
  int buttonPin;                   // physical pin number of button
  int relayPin;             // physical pin number of relay
  byte oldValue;                    // last Values for key (debounce)
  boolean relayState;               // relay status (also stored in EEPROM)
};

Relay Relays[noRelays]; 
Bounce debouncer[noRelays];
MyMessage msg[noRelays];

void setup(){
    sendHeartbeat();
    wait(250);
    // Initialize Relays with corresponding buttons
    for (int i = 0; i < noRelays; i++){
    Relays[i].buttonPin = buttonPin[i];              // assign physical pins
    Relays[i].relayPin = relayPin[i];
    msg[i].sensor = i;                                   // initialize messages
    msg[i].type = V_LIGHT;
    debouncer[i] = Bounce();                        // initialize debouncer
    debouncer[i].attach(buttonPin[i]);
    debouncer[i].interval(5);
    pinMode(Relays[i].buttonPin, INPUT_PULLUP);
    //digitalWrite(Relays[i].relayPin, RELAY_OFF);
    wait(250);
    pinMode(Relays[i].relayPin, OUTPUT);
    Relays[i].relayState = loadState(i);                               // retrieve last values from EEPROM
    digitalWrite(Relays[i].relayPin, Relays[i].relayState? RELAY_ON:RELAY_OFF);   // and set relays accordingly
    send(msg[i].set(Relays[i].relayState? true : false));                  // make controller aware of last status  
    wait(250);
    }
}
void presentation()  {
      sendSketchInfo("MultiRelayButton", "0.9f");
      wait(250);
      for (int i = 0; i < noRelays; i++)
      present(i, S_LIGHT);                               // present sensor to gateway
}
void loop()
    {
    for (byte i = 0; i < noRelays; i++){
    debouncer[i].update();
    byte value = debouncer[i].read();
    if (value != Relays[i].oldValue && value==0){
    Relays[i].relayState = !Relays[i].relayState;
    digitalWrite(Relays[i].relayPin, Relays[i].relayState?RELAY_ON:RELAY_OFF);
    send(msg[i].set(Relays[i].relayState? true : false));
    saveState( i, Relays[i].relayState );}                 // save sensor state in EEPROM (location == sensor number)
    
        Relays[i].oldValue = value;      
    }
}
// process incoming message 
void receive(const MyMessage &message){        
   if (message.type == V_LIGHT){ 
   if (message.sensor <noRelays){            // check if message is valid for relays..... previous line  [[[ if (message.sensor <=noRelays){ ]]]
   Relays[message.sensor].relayState = message.getBool(); 
   digitalWrite(Relays[message.sensor].relayPin, Relays[message.sensor].relayState? RELAY_ON:RELAY_OFF); // and set relays accordingly
   saveState( message.sensor, Relays[message.sensor].relayState ); // save sensor state in EEPROM (location == sensor number)
   }
  }
}

jeylites

The following sketch has got what you're looking for. Hope that helps.

Relay With Actuator Switch Toggle

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>
#define RELAY_ON 0                      // switch around for realy HIGH/LOW state
#define RELAY_OFF 1

MySensor gw;

#define RADIO_ID 11                    // Radio ID, whatever channel you assigned to
#define noRelays 6
const int relayPin[] = {A0, A1, A2, A3, A4, A5};
const int buttonPin[] = {3, 4, 5, 6, 7, 8};

class Relay				// relay class, store all relevant data (equivalent to struct)
{
public:                             		 
  int buttonPin;			// physical pin number of button
  int relayPin;				// physical pin number of relay
  byte oldValue;               		// last Values for key (debounce)
  boolean relayState;             	// relay status (also stored in EEPROM)
};

Relay Relays[noRelays];	
Bounce debouncer[noRelays];
MyMessage msg[noRelays];

void setup(){
	gw.begin(incomingMessage, RADIO_ID, true);
	delay(250);
	gw.sendSketchInfo("MultiRelayButton", "0.9b");
	delay(250);

	// Initialize Relays with corresponding buttons
	for (int i = 0; i < noRelays; i++){
	Relays[i].buttonPin = buttonPin[i];				             // assign physical pins
	Relays[i].relayPin = relayPin[i];
	msg[i].sensor = i;						             // initialize messages
	msg[i].type = V_LIGHT;
	debouncer[i] = Bounce();						     // initialize debouncer
	debouncer[i].attach(buttonPin[i]);
	debouncer[i].interval(5);
	pinMode(Relays[i].buttonPin, INPUT_PULLUP);
	pinMode(Relays[i].relayPin, OUTPUT);
	Relays[i].relayState = gw.loadState(i);			                      // retrieve last values from EEPROM
	digitalWrite(Relays[i].relayPin, Relays[i].relayState? RELAY_ON:RELAY_OFF);   // and set relays accordingly
	gw.send(msg[i].set(Relays[i].relayState? true : false));	              // make controller aware of last status
	gw.present(i, S_LIGHT);							      // present sensor to gateway
	delay(250);

	}
}

void loop()
	{
	gw.process();
	for (byte i = 0; i < noRelays; i++){
	debouncer[i].update();
	byte value = debouncer[i].read();
//	if (value != Relays[i].oldValue && value == 0){
        if (value != Relays[i].oldValue){
	Relays[i].relayState = !Relays[i].relayState;
	digitalWrite(Relays[i].relayPin, Relays[i].relayState?RELAY_ON:RELAY_OFF);
	gw.send(msg[i].set(Relays[i].relayState? true : false));
	gw.saveState( i, Relays[i].relayState );}                 // save sensor state in EEPROM (location == sensor number)
	
        Relays[i].oldValue = value;
        
	}
}

// process incoming message 
void incomingMessage(const MyMessage &message){
         
        if (message.type == V_LIGHT){ 
        if (message.sensor <noRelays){ 	 // check if message is valid for relays..... previous line if [[[ (message.sensor <=noRelays){ ]]]
        Relays[message.sensor].relayState = message.getBool(); 
        digitalWrite(Relays[message.sensor].relayPin, Relays[message.sensor].relayState? RELAY_ON:RELAY_OFF); // and set relays accordingly
        gw.saveState( message.sensor, Relays[message.sensor].relayState ); // save sensor state in EEPROM (location == sensor number)
		}
	}
}

niccodemi

@jeylites Thanks, toggle switch works but there is issue when node boots / restarts. On 1st restart relays stay OFF, on 2nd come ON, on 3rd again OFF and so on. It seems that whatever happens during Setup is reversed in Loop. Hopefully someone can point out what should be changed in modified sketch.

#define MY_RADIO_NRF24

#define MY_REPEATER_FEATURE

#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>
#define RELAY_ON 0                      // switch around for realy HIGH/LOW state
#define RELAY_OFF 1
//

#define noRelays 2                     //2-4
const int relayPin[] = {14,15};          //  switch around pins to your desire
const int buttonPin[] = {3,4};      //  switch around pins to your desire

class Relay             // relay class, store all relevant data (equivalent to struct)
{
public:                                      
  int buttonPin;                   // physical pin number of button
  int relayPin;             // physical pin number of relay
  byte oldValue;                    // last Values for key (debounce)
  boolean relayState;               // relay status (also stored in EEPROM)
};

Relay Relays[noRelays]; 
Bounce debouncer[noRelays];
MyMessage msg[noRelays];

void setup(){
    sendHeartbeat();
    wait(250);
    // Initialize Relays with corresponding buttons
    for (int i = 0; i < noRelays; i++){
    Relays[i].buttonPin = buttonPin[i];              // assign physical pins
    Relays[i].relayPin = relayPin[i];
    msg[i].sensor = i;                                   // initialize messages
    msg[i].type = V_LIGHT;
    debouncer[i] = Bounce();                        // initialize debouncer
    debouncer[i].attach(buttonPin[i]);
    debouncer[i].interval(5);
    pinMode(Relays[i].buttonPin, INPUT_PULLUP);
    //digitalWrite(Relays[i].relayPin, RELAY_OFF);
    wait(250);
    pinMode(Relays[i].relayPin, OUTPUT);
    Relays[i].relayState = loadState(i);                               // retrieve last values from EEPROM
    digitalWrite(Relays[i].relayPin, Relays[i].relayState? RELAY_ON:RELAY_OFF);   // and set relays accordingly
    send(msg[i].set(Relays[i].relayState? true : false));                  // make controller aware of last status  
    wait(250);
    }
}
void presentation()  {
      sendSketchInfo("MultiRelayButton", "0.9g");
      wait(250);
      for (int i = 0; i < noRelays; i++)
      present(i, S_LIGHT);                               // present sensor to gateway
}
void loop()
    {
    for (byte i = 0; i < noRelays; i++){
    debouncer[i].update();
    byte value = debouncer[i].read();
    if (value != Relays[i].oldValue){
    Relays[i].relayState = !Relays[i].relayState;
    digitalWrite(Relays[i].relayPin, Relays[i].relayState?RELAY_ON:RELAY_OFF);
    send(msg[i].set(Relays[i].relayState? true : false));
    saveState( i, Relays[i].relayState );}                 // save sensor state in EEPROM (location == sensor number)
    
        Relays[i].oldValue = value;      
    }
}
// process incoming message 
void receive(const MyMessage &message){        
   if (message.type == V_LIGHT){ 
   if (message.sensor <noRelays){            // check if message is valid for relays..... previous line  [[[ if (message.sensor <=noRelays){ ]]]
   Relays[message.sensor].relayState = message.getBool(); 
   digitalWrite(Relays[message.sensor].relayPin, Relays[message.sensor].relayState? RELAY_ON:RELAY_OFF); // and set relays accordingly
   saveState( message.sensor, Relays[message.sensor].relayState ); // save sensor state in EEPROM (location == sensor number)
   }
  }
}

these are screenshots from restarts

reboot1

reboot2

martinhjelmare

@niccodemi

Hi!

I think the problem is you're not initializing oldValue to anything. It will then always be different than value in the loop, and state will change.

You should set oldValue to the same "state" as the loaded relayState in setup. Even better, only use relayState, and make it an int. You can do the same boolean evaluations anyway. 1 is true and 0 is false.

Edit:
Sorry, I forgot that this is a pushbutton, right? Then you should just make sure that oldValue and value are the same after setup is complete, ie HIGH.

niccodemi

@martinhjelmare

thanks, I understand what you mean but I don't know how to write it in sketch.

I tried inserting

Relays[i].oldValue = Relays[i].relayState;

at the end of Void Setup section but then sketch wouldn't compile. I get "name lookup of 'i' changed 'for' ISO for scoping [-fpermissive]" error. I get same error if I substitute Relays[i].relayState with loadstate.

martinhjelmare

@niccodemi

Put this on a line after pinMode() in setup function.

Relays[i].oldValue = digitalRead(Relays[i].buttonPin);

niccodemi

@martinhjelmare

Ok, there is an improvement. Relays now turn to same state as they were before reboot most of the time but not always. Sometimes they inverse - the one which was OFF turns ON and vice-versa. Sometimes (1 in 3) they switch ON and OFF (only for split second) in the loop function. See below screenshots:

reboot3

reboot4

This sketch is used with toggle button, same as on this photo.

Array Relay Button Actuator

16

11.7k

11.2k

113.1k