ESP8266 WiFi gateway port for MySensors

[D_dude]

@mfalkvidd
Thank you, i will try this and post results.

[D_dude]

@mfalkvidd
tried erasing the flash using the method suggested but doesn't seem to be working for me. same result.
Thanks for the tip though.

[mfalkvidd]

Too bad. Thanks for posting your results.

[luisgcu]

here is my ESP8266 wifi gateway installed in wifi repeater box, taking the advantage that its has a 5 volts power supply.

[Yveaux]

@luisgcu Nice housing!
Thanks for the pics!

[soward]

I'd been using the ESP gateway for several weeks, but recently was having trouble adding a new sensor I am developing.

Since the copy of dev I built it with was now out of date, I went ahead and updated... still wasn't working right so while I had the serial link to it I checked and noticed it was crashing and cycling. It would work for hours, until I fired up my new node, then crash about immediately. A few dozen debug(PSTR())'s later, I found a cause.

In core/MySensorsCore.cpp the result of _msg.getConfig() is dereferenced in a comparison, and it's possible it could return NULL ( like when it's a new node ). I put a check around that and it's not crashing anymore. Which is more than what I can say for my new sensor node....

I have not tested this change with an AVR.

I submitted PR 264.

[mfalkvidd]

Great work @soward !

[D_dude]

on some basic debugging, seems like my sketch is crashing in setupGateway.

infact even adding a print statement, it only prints first 3 chars.

My question is setupGateway takes output as an arg, which in turn is a function, should there be some parameters for this function?
also "Serial.print(serialBuffer);" does not print anything i added prints above and before and they don't show up either.

  va_end (args);
  Serial.print("A1");
  Serial.print(serialBuffer);
  Serial.print("A2");

any suggestions?

[Yveaux]

@D_dude flush the serial output after each print.
The ESP will output the serial data in the background while your programm continues and then it crashes.

[Yht]

Hi,
I'm getting all the time this:

ESP8266 MySensors Gateway
Connecting to layla
......Connected!
IP: 192.168.0.102
0;0;3;0;9;gateway started, id=0, parent=0, distance=0

Then it got stuck so I do reset and getting this in loop:

ESP8266 MySensors Gateway
Connecting to layla
..Connected!
IP: 192.168.0.102
0;0;3;0;9;radio init fail

Soft WDT reset

ctx: cont
sp: 3ffefe70 end: 3fff00a0 offset: 01b0

stack>>>
3fff0020: 00000000 00000000 3ffeed74 40203665
3fff0030: 0000007f 3ffef074 40205ba0 3ffef080
3fff0040: 40202114 00000001 00000000 40205c10
3fff0050: 6600a8c0 00ffffff 0100a8c0 3ffef074
3fff0060: 3ffe84ac 3ffeee8c 3ffeefb0 4020256b
3fff0070: 3ffe86b8 6600a8c0 00000000 00000000
3fff0080: 3fffdc20 00000000 3ffef06d 40205bde
3fff0090: 00000000 00000000 3ffef080 40100114
<<<stack<<<

ets Jan 8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 1264, room 16
tail 0
chksum 0x42
csum 0x42
~ld

[Yveaux]

@Yht 0;0;3;0;9;radio init fail
Means there's something wrong with your nRF communication. The WDT reset following this is normal.

[ciprian]

i have been using wifi gateway with Domoticz controller without any problems until recentely. After the last update to beta version of the controller, the gateway crashes when the controller request gateway version:
Gateway startup complete.
Client 0: 0;0;3;0;2;

Exception (28):
epc1=0x4000bf80 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000000 depc=0x00000000

ctx: cont
sp: 3ffebf60 end: 3ffec1f0 offset: 01a0

I have tested with telnet client with the same request and it was ok. Then I saw that the request from controller was terminated with only <LF> and not with <CR><LF> and this is why it crashed. I have added the following to the sketch:

•    if (inChar == '\n')
    {  
      if (inputString[i].string[inputString[i].idx-1] != '\r') { // if the last char is not CR then add it
      inputString[i].string[inputString[i].idx++]='\r';
     }
      // a command was issued by the client
      // we will now try to send it to the actuator
  

and now it seems to work.
Is this the right way to go?
Thanks

[hek]

@ciprian

Are you talking abut this line of code?
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/core/MyGatewayTransportEthernet.cpp#L194

[ciprian]

@hek My code is from GatewayESP8266.ino example in Mysensors 1.5, line 234.

[hek]

Ok! Mis-read this line---

After the last update to beta version....

Thought you were talking about the development branch. Sorry.

[Yht]

Hi all,
First, I have to say this is awsome what @Yveaux did, thank you!

Sorry if this question takes you back in time. I don't know what channel and id to use for the nodes,I tried channel 97 and id from 1-5 but it is not working..
are you using mesh lib?

[Yveaux]

@Yht said:

I don't know what channel and id to use for the nodes

Just leave the default channel untouched for both sensors and gateway. It should be fine.
The gateway will automatically be assigned ID 0, the nodes can have any fixed ID.
Dynamic ID assignment requires some extra software, as the gateway does not support it.

[georgep56]

I'm also seeing my ESP8266 gateway crash when the controller requests its version.

I had not seen this thread so I started a new topic here: http://forum.mysensors.org/topic/2493/esp8266-wifi-gateway-crashes-and-reboots-when-controller-connects

[scalz]

hi,

maybe you have already seen it...but you can get cheap and smaller nodemcu. crazy price! I have ordered some, and waiting for them...
http://fr.aliexpress.com/item/D1-mini-Mini-NodeMcu-4M-bytes-Lua-WIFI-Internet-of-Things-development-board-based-ESP8266/32529101036.html?spm=2114.06010108.3.1.04LsjX&ws_ab_test=searchweb201556_2_79_78_77_80,searchweb201644_0,searchweb201560_9

[Yveaux]

@scalz Nice! Thanks for the link!