Hard to grab time and value sent from controller

[hek]

Have you looked at the TimeAwareSensor example?

[sundberg84]

Yea I did, and I dont see any difference from mine.
The thing is that I sleep my Sensor so i need a loop inside the void loop() to check if I recieved the time.

Maybe its hardware or the position of the sensor... ill try to relocate and load the sketch to another build

[TheoL]

@sundberg84 I haven't looked at your code, but do you put the Arduino to sleep after you've received the time or after you made the timeRequest to the controller? I'm not sure, but if you do the latter that might be your problem. I'm guessing that the Node is not able to receive messages from the gateway, when it's in sleep mode.

[sundberg84]

Hi.

No i recieve the time, check if its a new day and then sleep the node.
This is done every sleep cycle (20min),. (Im aware about the failure margin here).

I do not sleep the sensor until i got the new time so that should not be a problem.

[sundberg84]

Looking at MysController i get this when i get into the bad loop:

2015-10-16 16:27:20	INFO	Reply time request
2015-10-16 16:27:20	TX	7;255;3;0;1;1445012841
2015-10-16 16:27:20	RX	7;255;3;0;1;
2015-10-16 16:27:24	INFO	Reply time request
2015-10-16 16:27:24	TX	7;255;3;0;1;1445012844
2015-10-16 16:27:24	RX	7;255;3;0;1;
2015-10-16 16:27:28	INFO	Reply time request
2015-10-16 16:27:28	TX	7;255;3;0;1;1445012848
2015-10-16 16:27:28	RX	7;255;3;0;1;
2015-10-16 16:27:28	RX	5;0;1;0;4;1020
2015-10-16 16:27:31	INFO	Reply time request
2015-10-16 16:27:31	TX	7;255;3;0;1;1445012852
2015-10-16 16:27:31	RX	7;255;3;0;1;
2015-10-16 16:27:35	INFO	Reply time request
2015-10-16 16:27:35	TX	7;255;3;0;1;1445012855
2015-10-16 16:27:35	RX	7;255;3;0;1;
2015-10-16 16:27:38	INFO	Reply time request
2015-10-16 16:27:38	TX	7;255;3;0;1;1445012859
2015-10-16 16:27:38	RX	7;255;3;0;1;

@hek
Its like its working one way (Sensor -> Repteter -> Controller) but not the other way around. Is it not using the repeater and thats why the request with time is not getting back?

[sundberg84]

Or its a bad NRF batch i got... AGAIN :(
Notised its a new batch im on... have to try some other nrf in that patch. Works one way though...

[hek]

Also make sure you're running the latest in master branch on gw/repeater. There was a bug there earlier affecting outgoing messages through repeaters.

[sundberg84]

I run 1.4 gw and updated repeaters after bug was reporter (bad routing causing à loop). Its à bit job to update gw to 1.5. Do you think it can make any difference @hek ?

[hek]

I doubt it would change anything. It's the intermittent failure behaviour that is weird.

[sundberg84]

I have ordered new nrf radios. Let's hope the makey the difference.

[sundberg84]

New radio, pro mini and still the same problems :(
I cant get it.

Looking at the gw leds the recieve led blinks when the node sends out the request. 1 second later the controller and gw responds accoring to MYSController and i see the transmit and error led blink.

i have the node right beside the gw now and no repeaters.
Any clues, anyone???

[hek]

And how does the node log look like?

Did you upgrade to 1.5?

[sundberg84]

No i did not upgrade the gw since i had so much problems with the connections...

Nod serial as before:
(From startup)

send: 7-7-0-0 s=255,c=0,t=17,pt=0,l=3,sg=0,st=ok:1.5
send: 7-7-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
sensor started, id=7, parent=0, distance=1
send: 7-7-0-0 s=255,c=3,t=11,pt=0,l=10,sg=0,st=ok:Rain Gauge
send: 7-7-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.7
send: 7-7-0-0 s=1,c=0,t=10,pt=0,l=0,sg=0,st=ok:
Startup completed
send: 7-7-0-0 s=1,c=2,t=24,pt=0,l=0,sg=0,st=ok:
Request pulsecount
send: 7-7-0-0 s=1,c=2,t=24,pt=0,l=0,sg=0,st=ok:
Request pulsecount
send: 7-7-0-0 s=1,c=2,t=24,pt=0,l=0,sg=0,st=ok:
Request pulsecount
read: 0-0-7 s=1,c=2,t=24,pt=0,l=2,sg=0:52
Received last pulse count from gw: 52
send: 7-7-0-0 s=255,c=3,t=1,pt=0,l=0,sg=0,st=ok:
Getting Time
send: 7-7-0-0 s=255,c=3,t=1,pt=0,l=0,sg=0,st=ok:
Getting Time
read: 0-0-7 s=255,c=3,t=1,pt=0,l=10,sg=0:1446829805
Time received: 17

[hek]

DI you have a similar serial log for the gateway? Think you should try to upgrade to be aligned with 1.5. Don't remember what problems you had earlier...