Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors and Arduino IDE 1.6.7

Tom71 last edited by Tom71

Hello, i have Problems to compile MySensors Serial Gateway with the latest Adruino IDE 1.6.7 and the development Version from MySensors. There is no USBDevice.init() anymore. I disabled the call in MyMainDefault.cpp and it compiles an works fine. Is this an workaround?
Thomas
Reply Quote 0
1 Reply Last reply

1
Posts

822
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
LAN8720A - will mysensors work with this module
Development • • Marcin

3

0
Votes

3
Posts

22
Views

Thanks for the answer. I meant that Mysensors has ESP32 support but only in terms of WIFI. It supports e.g. stm32 with ENC or W5500 modules - and the question is whether and how to add ESP32 support with LAN8720 module. I am not considering using ESPHOME or MQTT - I want to have native communication with the controller that implements my control schemes on its side. I try to program KC868-A16 but it does not matter - the question is whether such support can be added in a simple way.
Home Assistant/MySensors quirks
Development • • OldSurferDude

1

0
Votes

1
Posts

8
Views

No one has replied
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

37
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

28
Views

@OldSurferDude yes, just run the configure command with --my-transport=none

MySensors and Arduino IDE 1.6.7

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

LAN8720A - will mysensors work with this module
Development • • Marcin

Home Assistant/MySensors quirks
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Gateway without a radio
Development • • OldSurferDude

52
Online

11.6k
Users

11.2k
Topics

112.9k
Posts

MySensors and Arduino IDE 1.6.7

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

LAN8720A - will mysensors work with this module Development • • Marcin

Home Assistant/MySensors quirks Development • • OldSurferDude

Radio waking up for no reason. Development • • Sasquatch

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Gateway without a radio Development • • OldSurferDude

52Online

11.6kUsers

11.2kTopics

112.9kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

LAN8720A - will mysensors work with this module
Development • • Marcin

Home Assistant/MySensors quirks
Development • • OldSurferDude

Radio waking up for no reason.
Development • • Sasquatch

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Gateway without a radio
Development • • OldSurferDude

52
Online

11.6k
Users

11.2k
Topics

112.9k
Posts