NRF24L01+ range of only few meters

[mfalkvidd]

@Igor-Katkov did you get better results with higher output power? I am no radio expert, but most stuff I have read says that higher output often results in worse signal to noise ratio.

[Igor Katkov]

@mfalkvidd Yes, a few more meters with PA_MAX.
Here is my best performing code

  radio.setPALevel(RF24_PA_MAX);
  radio.setDataRate(RF24_250KBPS);
  radio.setPayloadSize(4);
  radio.setChannel(2);
  radio.setRetries(15, 15);

Full code https://gist.github.com/ikatkov/6df540838bd4d3ea8b57

[mfalkvidd]

@Igor-Katkov interesting. Thanks for sharing!

[Igor Katkov]

It appears that I was quite foolish expecting FTDI adapter board to power my nrf24 :-(
datasheet says it can provide at most 50mA.

I'll try 2AA batteries and a step up regulator

[nunver]

@petewill Yes, I did increase PA level to Max. I don't understand how I could change the payload size, though. Mysensors have a certain format.

[AWI]

@Igor-Katkov powering the radio from a switching regulator is no guarantee for radio performance. Most of these (small) regulators have a high voltage ripple around their switching frequency.
You have no need for it either... The radio should work perfectly when powered by two cells.

[nunver]

@AWI It does not sound right to me having to use battery power where there is AC. There should be a way to get clean enough power for these little devices?

[AWI]

@nunver sure, use a standard regulated power supply (phone charger) of 5v for the Arduino and make sure the radio gets a stable supply from a regulator. What always works is using one of those nrf24 adapter plates (look in the shop) for a stable radio.

[Igor Katkov]

I was/am trying to make a battery powered wireless sensor so there would be no AC if I can avoid it.

I intended to use the step up regulator to 3v3 to extend sensor life on a pair of AA batteries. I think voltage would drop fairly quickly below nrf24 lower limit.

[Yveaux]

@Igor-Katkov said:

datasheet says it can provide at most 50mA

Don't count on that ftdi chip being genuine for only a few $$. I doubt if that data sheet applies to your unit...

[AWI]

@Igor-Katkov Your AA batteries will be as good as dead before these drop below the nrf24 minimum voltage (1.9V). See below the graph for one cell. If the arduino survives depends on hardware/ fuse-settings.

[Igor Katkov]

OK, so I tried with AA cells, no regulators.
Plain and simple. TMRh20 lib.
Not any better.
I then tried with a chunk of bare copper wire 83mm long, soldered to the end of that curly PCB antenna - not any better either.
Not sure what might I've done wrong. Layout is pretty simple

Voltage with load is 3.1V, current never goes above 19.2mA

I tried with direct line of sight, range has doubled to say 20m, but again - nothing to write home about.

[Igor Katkov]

[Update for future generation]
I think I found my issue. It was the large transceiver see image below, with power amplifier and external antenna.
Once I replaced both receiver and transmitter with identical units, range got significantly better.
60m clear sight and almost whole house through multiple walls.

For whatever reason small unit can't hear ACK from the PA unit. I tried to reduce power on the PA end to

 radio.setPALevel(RF24_PA_MIN); 

but it did not seem to have any effect. My best guess now is that oscillator on the PA unit is slightly off. PCB antenna unit is battery powered.
Power source to arduino UNO that drives PA unit is good, 5V less that 2mV ripple. The transceiver is powered via 3V3 output (onboard regulator) of UNO though, could it be the problem?

[Oitzu]

@Igor-Katkov said:
The transceiver is powered via 3V3 output (onboard regulator) of UNO though, could it be the problem?

Yes. But depends on which onboard regulator is used on your UNO.
Also have an look here: http://forum.mysensors.org/topic/3168/long-range-transmission/27

[petewill]

@Igor-Katkov said:

I think I found my issue. It was the large transceiver see image below, with power amplifier and external antenna.

I have had issues with my NRF radio like the one you mention here. I'm not sure about range issues but it totally stopped my Z-Wave network from communicating. It was easier for me to just use one of the smaller radios instead of doing further troubleshooting. I know there are some other threads (that I can't think of off the top of my head) where users have found that shielding it has helped. Also, as @Oitzu said, try powering it from a separate 3.3v source instead of from the Uno.

[Oitzu]

@petewill about shielding: you should have looked on the link http://blog.blackoise.de/2016/02/fixing-your-cheap-nrf24l01-palna-module/ . I explained it that often that i decided to write a blog article about it. :P

[petewill]

@Oitzu Awesome! I have one of these sitting in a drawer because of all the issues it caused me. :) I may need to pull it out and try your method one of these days. For now I have been getting by with the external hack but I'm sure I'll want further range at some point...

[Oitzu]

@petewill great to hear. Let me know if you are successful. :)

[pkjjneal]

This is great info. I actually had great luck with the chip antenna version with a mini pro and an UNO, and the range I wanted was just not there. I moved to the one with the PA+ ext antenna, and having a strange issue. If I swap out the chip antenna version for the PA+ ext antenna version on the mini pro, it only sends packets if I am physically touching the nRF board itself with my finger. The one connected to the UNO does not have this issue. It seems to be grounded sufficiently (only the GND pin on the nRF connector), and I changed the power source from the FTDI module to a separate 3.4V source with no difference in this behavior. Any ideas?

[Oitzu]

@pkjjneal said:
it only sends packets if I am physically touching the nRF board itself with my finger.

Also read: http://blog.blackoise.de/2016/02/fixing-your-cheap-nrf24l01-palna-module/
Its a typical behaviour i observed on badly shielded modules.