Curtain Control Node.

[franzelare]

I'm currently working on a similar project, only I got started with 24V DC motors that I got from my work (left overs from a test project) These motors are very strong (way way over rated) and have a big gearbox what unfortunately makes the movement a bit slow.
I started off with 1 motor to move 2 curtains at the same time, but will change this to 2 motors for either side since the better half of me likes to control the curtains separately in case she only wants to close 1.
Next to the automation there will also be a manual control switch be hidden behind the curtains in case the node is down and I'm not at home to fix the issue...
all running on an ESP8266 (ESP-12e) unit to have it over WiFi and have enough io

Currently the test setup is working fine and I'm ordering parts to start implementing this a bit bigger in the first room. the test setup I made with some old wood 1 meter of rail and a few old rugs as curtains...

I use a GT2 timing belt that is commently used for 3D printers and pully's are widely available as well as the belts in different lengths (I order them on rolls of 10 meters) and attached the timing belt to a carriage that is normally to pull the curtains with a rod.

the motor is mounted on a bracket with currently 2 end stop switches for open and close (but will be 1 switch for open and 1 for close in the final solution)

resulting in driving the curtain from 1 side

electronics are working fine now and need to be ported to a test print and later to a real PCB design

[romeok01]

Hello.

To my project i use stepper motor JK42HS34-0404 and driver L298N.

This is a wiring diagram.

This is a program code that I use

#include <MySensor.h>  
#include <SPI.h>
#include <AccelStepper.h>
#define HALFSTEP 4  // Stepper uses "Halfstep" mode
#define CURTAIN_CLOSED 1000 // value when closed
#define CURTAIN_OPEN 0 // value when open
#define CHILD_ID 1   // Id of the sensor child
// MySensors definitions
MySensor gw;
// Initialize message
MyMessage msg(CHILD_ID, V_TRIPPED);


// Motor pin definitions
#define motorPin1  3     // IN1 on the ULN2003 driver 1
#define motorPin2  4     // IN2 on the ULN2003 driver 1
#define motorPin3  5     // IN3 on the ULN2003 driver 1
#define motorPin4  6     // IN4 on the ULN2003 driver 1

// Initialize with pin sequence IN1-IN3-IN2-IN4 for using the AccelStepper with 28BYJ-48
AccelStepper stepper1(HALFSTEP, motorPin1, motorPin2, motorPin3, motorPin4);

unsigned long current_position ; // remembers current position, need to be saved in EEPROM?

void setup() {
  // MySensors
  gw.begin(); // fixed node 13
  gw.sendSketchInfo("Curtain control 13", "1.0"); // Send the sketch version information to the gateway and Controller

  //pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
  
  stepper1.setMaxSpeed(500.0);
  stepper1.setAcceleration(700.0);
  stepper1.moveTo(CURTAIN_OPEN);
  
  current_position = CURTAIN_OPEN ;
  stepper1.moveTo(CURTAIN_OPEN);
}//--(end setup )---

void loop() {
  // if message = V_UP start moving until closed
  // if message = V_DOWN start moving back until open
  // if message = V_STOP stop moving
  // Test: Change direction when the stepper reaches the target position
  gw.process(); // check if message from controller
  if (stepper1.distanceToGo() == 0){
    if (stepper1.currentPosition() == CURTAIN_OPEN){
      stepper1.moveTo(CURTAIN_CLOSED);
      Serial.println("Curtain Open, now closing");
      gw.request(CHILD_ID, V_UP, 0); // request new values from controller  
    }
    else{
      stepper1.moveTo(CURTAIN_OPEN);
      Serial.println("Curtain Closed, now opening");
      gw.request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
  }
  
  stepper1.run();
}

// This is called when a message is received 
void incomingMessage(const MyMessage &message) {
  // We only expect few types of messages from controller, check which
  stepper1.moveTo(message.getInt() * CURTAIN_CLOSED/100);
  Serial.print("Message - valid: ");
  Serial.print(message.sensor);
  Serial.print(" , value: % ");
  Serial.println(message.getInt());
  switch (message.getInt()) {
  case 100:
    // Curtain should be opened
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message UP ");
     stepper1.moveTo(CURTAIN_OPEN);
     break;
  case 0:
    // Curtain should be closed
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message DOWN ");
     stepper1.moveTo(CURTAIN_CLOSED);
    break;
  case 50:
    // Curtain action should be stopped
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message STOP ");
    break;
  default: 
    // not recognizable message
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Unrecognized ");

  }
 
}

When the program I have uploaded to my mysensors, the engine still turns, one left and one to the right and did not work the button blinds in Domoticz.

I cant turn off my stepper motor in Domoticz.

https://www.youtube.com/embed/1Wc1p_9YDQQ

Please help me.

[romeok01]

I write a program on library Stepper not AccelStepper.
Now is working.

Program code:

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <Stepper.h>

#define CURTAIN_CLOSED 1000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN -1000         // wartosc gdy kurtyna otwarta 
#define CHILD_ID 1

// definicje MySensors 

MyMessage message(CHILD_ID, S_COVER);

int in1Pin = 3;
int in2Pin = 4;
int in3Pin = 5;
int in4Pin = 6;
int lastState;
 
// liczba kroków na jeden obrót
#define stepsPerRevolution 200

//ustawienie szybkości silnika 
int motorSpeed = 40;

Stepper myStepper(stepsPerRevolution, in1Pin, in2Pin, in3Pin, in4Pin);

void setup() {
  
// ustawienie pinów jako wyjście
  pinMode(in1Pin, OUTPUT);
  pinMode(in2Pin, OUTPUT);
  pinMode(in3Pin, OUTPUT);
  pinMode(in4Pin, OUTPUT);
// ustawienie szybkosci silnika
  myStepper.setSpeed(motorSpeed);
}

void presentation()  
{ 
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Program kurtyna", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void receive(const MyMessage &message) {
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     myStepper.step(CURTAIN_OPEN);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
        }
     
 if (message.type==V_DOWN) {
     myStepper.step(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_DOWN, 0); // request new values from controller
        } 
}

I use MySensors Library 2.0

Youtube film

https://www.youtube.com/embed/gm0r2kDXrt4

[franzelare]

your wiring diagram is not accessable:
Error (403)
It seems you don't belong here! You should probably sign in. Check out our Help Center and forums for help, or head back to home.

i use a DC motor so can't help with stepper motors, but can you share an image of how you setup your rails?

[romeok01]

Now the wiring diagram should be visible.

[romeok01]

I write program with AccelStepper library

/ Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <AccelStepper.h>      //import biblioteki AccelStepper 

#define HALFSTEP 8
#define CURTAIN_CLOSED 2000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN 0       // wartosc gdy kurtyna otwarta
#define CHILD_ID 1

// definicje MySensors

MyMessage message(CHILD_ID, S_COVER);

// Definicja pinow silnika
#define IN1  3     // IN1 - zielony
#define IN2  4     // IN2 - czarny
#define IN3  5     // IN3 - niebieski
#define IN4  6     // IN4 - czerwony
 
AccelStepper stepper1(HALFSTEP, IN1, IN2, IN3, IN4);

void setup()
{
  stepper1.setMaxSpeed(200.0);
  stepper1.setAcceleration(1000.0);
  stepper1.setSpeed(200);
  stepper1.moveTo(CURTAIN_OPEN);
}

void presentation() 
{
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Program kurtyna", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void loop()
{
  stepper1.run();  //Start
}

void receive(const MyMessage &message)
{
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     if (stepper1.distanceToGo() == 0){
         if (stepper1.currentPosition() == CURTAIN_OPEN){
             stepper1.moveTo(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
         }
      }
   }
   if (message.type==V_DOWN) {
       stepper1.moveTo(CURTAIN_OPEN);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
    if (message.type==V_STOP) {
        stepper1.setCurrentPosition(0);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        request(CHILD_ID, V_STOP, 0); // request new values from controller
    }
}

I use MySensors library 2.0

Now i working.

[jacikaas]

Hello,

I trying to adopt the code for 28BYJ-48 stepper motor with ULN2003 driver board for roller blinds control. Code is working, but when the stepper motor is always on - it gets hot. Because of it also its consumes more energy. So thats why I want to turn on ULN2003 board only when new action is started, and after that it should be shuted down again. I could do it, because ULN2003 has On/Off jumper:

Question #1: I trying to use relay for that On/Off. Could I do it without relay and control On/Off jumper directly from arduino? Does relay is the best solution?

Question #2: I suck at programming, but I trying to add theese lines to my code to control the relay SIL05-1A72-71D, which controls the ULN2003 driver board:
int powerPin = 7; //before SETUP
pinMode(powerPin, OUTPUT); // In SETUP
digitalWrite(powerPin, LOW); // In SETUP
digitalWrite(powerPin, HIGH); // In void receive function
delay(CURTAIN_CLOSED); // In void receive function
digitalWrite(powerPin, LOW); // In void receive function

digitalWrite(powerPin, HIGH); - I think is in right position, but I don't know how to turn off relay when action is done. Please advise for coding, because I not good in it. Thank You! Below is the code:

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_NODE_ID 10
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
//#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <AccelStepper.h>      //import biblioteki AccelStepper 

#define HALFSTEP 8
#define CURTAIN_CLOSED 10000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN 0       // wartosc gdy kurtyna otwarta
#define CHILD_ID 1

int powerPin = 7;

// definicje MySensors

MyMessage message(CHILD_ID, S_COVER);

// Definicja pinow silnika
#define IN1  3     // IN1 - zielony
#define IN2  4     // IN2 - czarny
#define IN3  5     // IN3 - niebieski
#define IN4  6     // IN4 - czerwony
 
AccelStepper stepper1(HALFSTEP, IN1, IN3, IN2, IN4);

void setup()
{
  stepper1.setMaxSpeed(1000.0);
  stepper1.setAcceleration(100.0);
  stepper1.setSpeed(200);
  stepper1.moveTo(CURTAIN_OPEN);
  
  pinMode(powerPin, OUTPUT);
  digitalWrite(powerPin, LOW);
}

void presentation() 
{
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Roller blinds", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void loop()
{
  stepper1.run();  //Start
}

void receive(const MyMessage &message)
{
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     digitalWrite(powerPin, HIGH);
     if (stepper1.distanceToGo() == 0){
         if (stepper1.currentPosition() == CURTAIN_OPEN){
             stepper1.moveTo(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
         }
      }
   }
   if (message.type==V_DOWN) {
       digitalWrite(powerPin, HIGH);
       stepper1.moveTo(CURTAIN_OPEN);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
    if (message.type==V_STOP) {
        digitalWrite(powerPin, HIGH);
        stepper1.setCurrentPosition(0);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        request(CHILD_ID, V_STOP, 0); // request new values from controller
    }
 //   delay(CURTAIN_CLOSED);
 //   digitalWrite(powerPin, LOW);
}

[Suresh Mali]

@jacikaas said in Curtain Control Node.:

void receive(const MyMessage &message)
{
// if message = V_UP start moving until closed
if (message.type==V_UP) {
digitalWrite(powerPin, HIGH);
if (stepper1.distanceToGo() == 0){
if (stepper1.currentPosition() == CURTAIN_OPEN){
stepper1.moveTo(CURTAIN_CLOSED);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_UP, 0); // request new values from controller
}
}
}
if (message.type==V_DOWN) {
digitalWrite(powerPin, HIGH);
stepper1.moveTo(CURTAIN_OPEN);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_DOWN, 0); // request new values from controller
}
if (message.type==V_STOP) {
digitalWrite(powerPin, HIGH);
stepper1.setCurrentPosition(0);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_STOP, 0); // request new values from controller
}
// delay(CURTAIN_CLOSED);
// digitalWrite(powerPin, LOW);
}

You can enable and disable outputs and try. In the following function:

void receive(const MyMessage &message)

//add the following at the begining of the function
stepper1.enableOutputs ()
//and add the following at the end in the same function.
stepper1.disableOutputs ()

I hope this helps haven't tried it myself.

[jacikaas]

@suresh-mali Thank You Suresh for Your answer!
I disconnect relay and delete it lines from the code.

I add lines to code like You said:

void receive(const MyMessage &message)
{
stepper1.enableOutputs ();
 // rest of code
stepper1.disableOutputs ();
}

It looks like it have to work because it is simple solution, but it doesn't... On driver board ULN2003, when motor is not rotating, A Led is always on. I think if command with disableOutputs would be activated, then the LED should not be on?

[Suresh Mali]

@jacikaas Ok.

//Remove this line from loop function
stepper1.run(); 

//Change this line
stepper1.moveTo(CURTAIN_CLOSED);
//to
stepper1.runToPosition(CURTAIN_CLOSED);

I hope this works. Also make similar changes in block which closes curtains.
Refernce article: https://www.pjrc.com/teensy/td_libs_AccelStepper.html

[jacikaas]

@suresh-mali
I now reading about that funktions in http://www.airspayce.com/mikem/arduino/AccelStepper/classAccelStepper.html#a344f58fef8cc34ac5aa75ba4b665d21c

Did what You said, but getting error: no matching function for call to 'AccelStepper::runToPosition(int)'
I paste here all code, but I think I did everything without mistakes:

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_NODE_ID 10
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
//#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <AccelStepper.h>

#define HALFSTEP 8
#define CURTAIN_CLOSED 10000
#define CURTAIN_OPEN 0
#define CHILD_ID 1

// int powerPin = 7;

// definicje MySensors

MyMessage message(CHILD_ID, S_COVER);

// Definicja pinow silnika
#define IN1  3     // IN1
#define IN2  4     // IN2
#define IN3  5     // IN3
#define IN4  6     // IN4
 
AccelStepper stepper1(HALFSTEP, IN1, IN3, IN2, IN4);

void setup()
{
  stepper1.setMaxSpeed(1000.0);
  stepper1.setAcceleration(100.0);
  stepper1.setSpeed(200);
  stepper1.runToPosition(CURTAIN_CLOSED);
}

void presentation() 
{
  sendSketchInfo("Roller blinds", "1.0");
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void loop()
{
  //stepper1.run();  //Start
}

void receive(const MyMessage &message)
{
stepper1.enableOutputs ();
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     if (stepper1.distanceToGo() == 0){
         if (stepper1.currentPosition() == CURTAIN_OPEN){
             stepper1.runToPosition(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
         }
      }
   }
   if (message.type==V_DOWN) {
       stepper1.moveTo(CURTAIN_OPEN);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
    if (message.type==V_STOP) {
        stepper1.setCurrentPosition(0);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        request(CHILD_ID, V_STOP, 0); // request new values from controller
    }
stepper1.disableOutputs ();
}

[skywatch]

@jacikaas Sorry to revive an old thread, but did you get this resolved and if so how?

I just 3D printed my first motorised roller blind mounts and have tested with arduino stepper only.

Next is to go mysensors with it, but which way is best? Standard arduino stepper or accelstepper?

[xydix]

Okey. This is an old thread but I hope it's ok I keep it alive.
I just printed som parts for my blinds.
I use a stepper motor (28BYJ-48 with ULN2003 Driver board) and this sketch found in this thread.
The sketch is awesome.
To my quiestion.
I want to run 2 blinds at the same time from ONE node. Synchronized or maybe individual.
Is this possible?
There isn't any digital pins over for this when using button(s).
I think i saw someone using analog pin connected to the ULN2003 someware.
Is it possible to run 2 motors on one board?
Really hope somone can answer som of my question.
What modifications is needed in the sketch if this is possible.
This is the sketch I use.

/*
 PROJECT: MY Sensors curtain controller
 PROGRAMMER: AWI
 DATE: march 11, 2016
 FILE: AWI stepper1.ino
 LICENSE: Public domain

 Hardware: ATMega328p board w/ NRF24l01
	and MySensors 2.0 (Development)
		
Special:
	uses AccelStepper library
	
Summary:
	Curtain control with stepper motor. 
	Manual operation with 1 push button 
	Calibration with manual button

Remarks:
	Fixed node-id
	
Change log:
20160312 - Cleanup
*/

// Enable debug prints to serial monitor
#define MY_DEBUG 

#define MY_NODE_ID 13											// fixed node number
// Enable and select radio type attached
#define MY_RADIO_RF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensors.h> 

// stepper library
#include <AccelStepper.h>										// http://www.airspayce.com/mikem/arduino/AccelStepper/
#define HALFSTEP 8  											// Stepper uses "Halfstep" mode

// button library
// used for:
// - manual open close - single click: close/ stop/ open/ stop
// - calibration  - after long press: open calibarion- until single press - closed calibration - until single press (stop)
#include <Button.h>												// https://github.com/JChristensen/Button

#define CHILD_ID 1   											// Id of the sensor child

#define SN "Curtain control 13"
#define SV "1.0"

#define buttonPin1 7  											// Arduino pin connected to buttonPin1
#define buttonPin2 A0  											// Arduino pin connected to buttonPin2 (fixed to ground)

// Motor pin definitions
#define motorPin1  3     										// IN1 on the ULN2003 driver 1
#define motorPin2  4     										// IN2 on the ULN2003 driver 1
#define motorPin3  5     										// IN3 on the ULN2003 driver 1
#define motorPin4  6     										// IN4 on the ULN2003 driver 1

const unsigned long heartbeatInterval = 1 * 3600UL * 1000UL ;	// heartbeatinterval
unsigned long heartbeatCounter = 0 ;

//
// helper routines to store and retrieve long in mysensors EEPROM
union {															// used to convert long to bytes for EEPROM storage
	long longInt;
	uint8_t LongByte[4];
	} convLongInt ;

void saveStateL(int EEposition, long StateL){
	convLongInt.longInt = StateL ;
	for (int y = 0; y < 4 ; y++){								// convert to bytes
		saveState(EEposition + y , convLongInt.LongByte[y]) ;
		}
	Serial.print("State saved: "); Serial.println(StateL);
	}
		
long loadStateL(int EEposition){
	for (int y = 0; y < 4 ; y++){								// convert from bytes
		convLongInt.LongByte[y] = loadState(EEposition + y) ;
		}
	Serial.print("State read: "); Serial.println(convLongInt.longInt);
	return convLongInt.longInt ;
	}
	

// Initialize with pin sequence IN1-IN3-IN2-IN4 for using the AccelStepper with 28BYJ-48
AccelStepper stepper1(HALFSTEP, motorPin1, motorPin3, motorPin2, motorPin4);
// Initialize button active low, debounce and internal pull-up
Button myBtn(buttonPin1, true, true, 40);						// Initiate the button (pin, pull_up, invert, debounce_ms)

MyMessage percentageMsg(CHILD_ID, V_PERCENTAGE);				// used to send updates to controller

const long maxRun = 4000000L ;									// maximum runway
long setPosition = 0 ; 											// remembers set position, need to be saved in EEPROM
const int setPositionEE = 4 ;									// eeprom location
long openPosition = 0 ; 										// Position at open, need to be saved in EEPROM?
const int openPositionEE = setPositionEE + 4 ;					// eeprom location
long closedPosition = 120000UL ; 								// Position at full close, need to be saved in EEPROM
const int closedPositionEE = openPositionEE + 4 ;				// eeprom location

unsigned long idleTimer = millis() ;							// return to idle timer
unsigned long idleTime = 100000UL ;								// return to idle after 100 secs

unsigned long printTimer = millis() ;							// print timer
unsigned long printTime = 1000UL ;								// print after 1 secs

enum position_t {Open, Close, Idle, Running} ;
position_t lastDirection = Open ; 								// lastDirection only for buttonpress
position_t runStatus = Idle ;									// indicates current status for running motor. used for status reporting to controller

enum State_t {sIdle, sCalibrateOpen, sCalibrateClose} ;
State_t State = sIdle ;


void setup() {
	// setup buttons
	pinMode(buttonPin1, OUTPUT);
	stepper1.setMaxSpeed(2000.0);
	stepper1.setAcceleration(1000.0);
	//saveStateL(closedPositionEE, closedPosition) ; 			// INIT: save closed position in EEPROM
	closedPosition = loadStateL(closedPositionEE) ;				// need to get last values from EEPROM and assume the current position is correct
	setPosition = loadStateL(setPositionEE) ;
	stepper1.setCurrentPosition(setPosition );
}//--(end setup )---

void presentation() {
  present(CHILD_ID, S_COVER, "Curtain");						// Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP

  // Register the LED Dimmable Light with the gateway
  sendSketchInfo(SN, SV);
}


void loop() {
unsigned int now = millis() ;								// current time for loop
// simple state machine for button press
	myBtn.read();  
	switch (State) {
        // Idle state, waiting for some action
		// - button press
		// - idleTimer
        case sIdle:                
            if (myBtn.wasReleased()){						// idle
				Serial.println("Button release") ;
				// if running stop
				if (stepper1.isRunning()){
					setPosition = stepper1.currentPosition();
					stepper1.moveTo(setPosition) ;			// move to current position (was already there..)
				} else if (lastDirection == Open) {
					stepper1.moveTo(closedPosition) ;
					lastDirection = Close ;
				} else {									// lastDirection == Close
					stepper1.moveTo(openPosition) ;
					lastDirection = Open ;
				}	
			} else if (myBtn.pressedFor(3000)){				// move to calibratete state with long press
				Serial.println("Button press long") ;
				idleTimer = now ;							// return to idle after ...
				State = sCalibrateOpen ;
				stepper1.move(-maxRun) ;					// let the stepper open with maximum
				}
			break ;
		// if not running and last action was open close ;  else open
		// if longpress Calibrate open
        case sCalibrateOpen:           						// calibration going on     
			if (myBtn.wasPressed()){
				stepper1.setCurrentPosition(0 );		// set new 0 position ??
				openPosition = setPosition = 0 ;
				State = sCalibrateClose ;					// next is close calibarion
				stepper1.move(maxRun) ;						// let the stepper close with maximum
			} else if (now > idleTimer + idleTime) {		// timer expired -> abort calibration
				State = sIdle ;
			}
			break ;
        case sCalibrateClose:								// calibrate closed position, end with keypress
			if (myBtn.wasPressed())	{
				closedPosition = setPosition = stepper1.currentPosition() ;
				saveStateL(closedPositionEE, closedPosition) ; // save closed position in EEPROM
				State = sIdle ;
				stepper1.moveTo(openPosition) ;				// return to open after calibration
			} else if (now > idleTimer + idleTime) {		// timer expired -> abort calibration
				State = sIdle ;
			}
			break ;
		default :
			break ;
		}
	// power off stepper if not running (no need to reenable))
	if (!stepper1.isRunning()){
		if (runStatus != Idle){								// there was a change in runningstatus, so report to controller
			setPosition = stepper1.currentPosition() ;		// store in EEPROM and report ready to controller
			saveStateL(setPositionEE, setPosition) ;
			send( percentageMsg.set((100 * setPosition)/(closedPosition - openPosition))) ;
			runStatus = Idle ;
		}
		stepper1.disableOutputs();
	} else {
		runStatus = Running ;
	}
	stepper1.run();
	/*
	if (printTimer++ > now + printTime){
		printTimer = now ;
		Serial.println(stepper1.currentPosition());
		}
	*/
}

// This is called when a message is received 
void receive(const MyMessage &message) {
// We only expect few types of messages from controller, check which
  switch (message.type) {
	case V_PERCENTAGE:
	// Curtain should be opened
	stepper1.moveTo(message.getInt() * (closedPosition - openPosition)/100);
	Serial.print("Message: "); Serial.print(message.sensor); Serial.print(" , value: % "); Serial.println( message.getInt());
	Serial.print("Moving to: "); Serial.println(message.getInt() * (closedPosition - openPosition)/100);
	break ;
	case V_STATUS:
	// Curtain should be opened or closed full
	stepper1.moveTo((message.getInt() == HIGH)?openPosition:closedPosition);
	Serial.print("Message - valid: ");
	Serial.print(message.sensor);
	Serial.print(" , value: % ");
	break ;
	default : 
	// not recognizable message
	Serial.print("Message - valid: ");
	Serial.print(message.sensor);
	Serial.print(", Unrecognized ");
	break ;
	}
  }

[TheoL]

You can use an I/O expander like an MCP23017 which is a 16 port expander or a 8 port expander. They're cheap. Keep in mind they consume 1 mAmp. I'm currently working on a product to overcome that power issue for a battery powered Node. Will try to post about it in a while

[TON RIJNAARD]

@xydix
Hello @xydix do you have the curtain working with the sketch above?
I don't get the button working on pin 7.
Witch button library do you use?
I have the library witch is in the sketch, i only must change Bbutton.h in LC_Button.h.
Is that maby my problem.
I hope u can help me.
Greatz Ton

[SENIORA]

@barduino said in Curtain Control Node.:

@Suresh-Mali

DC Motor, very interesting!

Do you have end stops? The sketch doesn't open for some reason...

Cheers

I have been working on a similar project last week. The mechanics and ´looks´ are the most difficult part for me.

[xydix]

@ton-rijnaard
Hi. This was a problem for me to. The reason is the library changed name and updates was made.
I use the library version 0.9.
I have like zero skills in arduino. If you use the old library the button will work with the sketch i posted a moth ago.
Looke here: https://github.com/JChristensen/JC_Button/releases
Maybe some of the other older releases will work. Don't remember why o choose V0.9
Look at 2.0.0, "This is a major release that is not backwards-compatible with previous releases."

[xydix]

@xydix
To answer my own question the stepper runs fine from the analog pins.
Next step is to find some intersted in the same thing and see if we could get the sketch adjusted to run two steppers.
I will try when i get some time but I guess I will have problem to clone the calibration and store-to-eerprom-part.

[adds666]

@AWI Sorry for butting in to an old thread, but automating my blinds is top priority!

I've copied your sketch and have everything setup - however, I have eratic behaviour and a few questions:

void setup() {
  // setup buttons
  pinMode(buttonPin1, OUTPUT);
  stepper1.setMaxSpeed(2000.0);
  stepper1.setAcceleration(1000.0);
  //saveStateL(closedPositionEE, closedPosition) ;      // INIT: save closed position in EEPROM
  closedPosition = loadStateL(closedPositionEE) ;       // need to get last values from EEPROM and assume the current position is correct
  setPosition = loadStateL(setPositionEE) ;
  stepper1.setCurrentPosition(setPosition );
}//--(end setup )---

• Should the pinMode on buttonPin1 actually be an INPUT?

• Can you please describe how to go about calibrating the system?

• Does the //saveStateL(closedPositionEE, closedPosition);
  need uncommenting for one boot of the arduino and the blind closed - then the sketch re-uploading with it commented again?

Your help is greatly appreciated as I have a twitching motor and feel I'm almost there!

[xydix]

@adds666 What i can tell it was a long time since @AWI was active here.
I use this sketch with my first bild since a couple of days.
For me it works like a charm. But in my case I control the motor from analog pins just to test and it seems OK.
No problem with the button.
The only thing I don't like, is the calibration.
I my case, using this on a blind, when calibrating, first it goes down, then i press the button, the blind stops at once and change it's direction and goes up. But when i reach the top level and want to stop it and save the state, it stops slow and pass the point i pressed the button and then reverse to the right spot. Problem is, the blind can't go further because it is in the top position.
If it would be the other way around it wouldn't be a problem.
Maybe i have the motor one the "wrong" side of the blind but when it is down the "downkey" in my HA is greyed out.
When it i up the "upkey" it greyed out so that seems right.

What is not working in your case?
What motor do you use? I use 28BYJ-48 with ULN2003 and had to set stepper1.setMaxSpeed(2000.0); to stepper1.setMaxSpeed(1000.0); because the motor "slipped" at a speed of 2000.
Like i wrote earlier in the thread I tried to figure out how to "dublicate" the sketch and ute it for two motors.
I really don't know where to start to get this done. It would be awesome to use one arduino with two blinds.