Homini Complete Room Sensor Module?
-
@samuel235 cool. yep mainboard is like an arduino (here an atsam=arduino zero) so it can work without daughter board. it depends what you need. mysxconnector is not my idea ;)
if you are curious (or perhaps @tbowmo lol) here a small pic of what I have received this week, not assembled yet..
http://www.hostingpics.net/viewer.php?id=43362320160320134635.jpg
On left my esp8266 adapter for nextion hmi screen (easy to solder 1206, optional lipo charger, onewire, si7021 and bh1750 emplacement...for a mqtt thermostat for instance, i am making sort of GUI). And on right a gorgeous panel with one stencil!! (multisensors with pir, my atsam lora/nrf mainboard, daughters boards (weather, gesture..), and adafruit m0 boards (why not!). Lot of tinker in perspective! It was cheaper to make everything on one board and cut myself than buying a multiple sub pcb + multiple stencil (for proto only). -
@samuel235 cool. yep mainboard is like an arduino (here an atsam=arduino zero) so it can work without daughter board. it depends what you need. mysxconnector is not my idea ;)
if you are curious (or perhaps @tbowmo lol) here a small pic of what I have received this week, not assembled yet..
http://www.hostingpics.net/viewer.php?id=43362320160320134635.jpg
On left my esp8266 adapter for nextion hmi screen (easy to solder 1206, optional lipo charger, onewire, si7021 and bh1750 emplacement...for a mqtt thermostat for instance, i am making sort of GUI). And on right a gorgeous panel with one stencil!! (multisensors with pir, my atsam lora/nrf mainboard, daughters boards (weather, gesture..), and adafruit m0 boards (why not!). Lot of tinker in perspective! It was cheaper to make everything on one board and cut myself than buying a multiple sub pcb + multiple stencil (for proto only).@scalz, looks awesome! I too have a feeling that i will be ordering this module all on one board and maybe separating them up myself. Again, like you, it would work out a lot cheaper that way when there is a few different boards to make up one completed module.
-
Currently looking at air quality sensors, while the MQ2 is the most favored around here, it uses up to 800mW of power at 5v, which to me is pretty high when you have IC's like that of ccs801 which uses much much lower. I'm looking to have these directly on the PCB itself, so in this respect they do not need to be available on a pcb of their own like the MQ2 is.
-
Specifically looking at CCMOS and their range of air quality sensors. Due to them using waffer layer technology they have brought down the power consumption to <10mW compared to the standard Metal Oxide method of other sensors using >800mW.
Some data on their sensor that looks very appealing right now:
CCS801
Product Brief: http://www.ccmoss.com/sites/default/files/documents/CC-000083-DS-6-Product brief for CCS801.pdf
Data Sheet: https://www.terraelectronica.ru/show_pdf.php?pdf=/pdf/CCMOSS/MOX CCS801.pdfThey also do this chip with a built in ADC, however that is still not available yet, its still in sampling phases and not available for normal purchases. So i'll divert my attention to the analog version. I don't see any issues regarding it being analog, if anyone does please point them out to me.
Just some food for thought for tonight ;)
-
@Samuel235 nice sensors, I like sensors too..that make me thinking to try to make a small childboard lol I have no time.
I think @epierre is the air quality guru here :) curious to know what do you think..But this little "nugget" certainly need some care like:
- it is fragile (during assembly, esd, heat..), and it is dfn. so it's better to not fail during soldering because it is 7$!! and not sure it likes multiple solder/desolder.
- its low power ability is possible only if you use pwm to heat it (or it will be a lot more). So it would require that mcu generate pwm during sleep! not possible in deep sleep ;) everything is powered off. The best bet (what I would do in this case if would do low power) would be to use timer2 in asynchronous mode to generate pwm and keep low power. or, if no pwm + deepsleep so no heater, I don't know how long time it really need to take a reliable value from mcu wakeup (need to be tested)
- imho adc is not always as easy as it seems. curve (could need opamp maybe not here I don't know its curve), is it sensible to parasite, does it need filtering, etc..but that is electronic debug. That's cool when the chip has everything packaged with i2c and you just need to have a clean supply.
- so follow only the ref schematic in datasheet may be not enough. but enough to play with, at debug you will see if you need to stabilize/improve adc or not
it's only imho, maybe I'm wrong or forgot details, but if it can help. btw cool idea :)
-
@Samuel235 nice sensors, I like sensors too..that make me thinking to try to make a small childboard lol I have no time.
I think @epierre is the air quality guru here :) curious to know what do you think..But this little "nugget" certainly need some care like:
- it is fragile (during assembly, esd, heat..), and it is dfn. so it's better to not fail during soldering because it is 7$!! and not sure it likes multiple solder/desolder.
- its low power ability is possible only if you use pwm to heat it (or it will be a lot more). So it would require that mcu generate pwm during sleep! not possible in deep sleep ;) everything is powered off. The best bet (what I would do in this case if would do low power) would be to use timer2 in asynchronous mode to generate pwm and keep low power. or, if no pwm + deepsleep so no heater, I don't know how long time it really need to take a reliable value from mcu wakeup (need to be tested)
- imho adc is not always as easy as it seems. curve (could need opamp maybe not here I don't know its curve), is it sensible to parasite, does it need filtering, etc..but that is electronic debug. That's cool when the chip has everything packaged with i2c and you just need to have a clean supply.
- so follow only the ref schematic in datasheet may be not enough. but enough to play with, at debug you will see if you need to stabilize/improve adc or not
it's only imho, maybe I'm wrong or forgot details, but if it can help. btw cool idea :)
I do plan on sourcing a hot air reflow station for DFN packages now, simply because of that pad on the bottom, otherwise i'de use a soldering iron for it. I'm pretty confident with soldering so this is the least of my issues if i'm honest.
Even though i'm looking to power this node via mains 240v, i'de love to get this whole node as low power as i possibly can. Initially i wasn't planning on sleep the MCU tbh, but i haven't evaluated the pins needed for the sensors yet, it might be a case that they will all be connected through interupt enabled pins, the new ATmega328pb may have more interupts, research needed. So if i could get them all on interupt enabled pins that would be fantastic news for power consumption to allow the MCU to sleep while monitoring is being performed still. It would be interesting to see if i could use some other IC to generate the pwm signal for this chip to be powered easily while MCU is sleeping, if i choose deepsleep that is. Normal sleep may be the only opinion anyway for me though.
I've ran into a few little issues in the past with ADC, namely the battery voltage monitor. So i think the fact it is analog is perfect for my application. However, i do think that it is all contained internally and just need clean power on that ADC version. But that isn't available anyway.
I'll now wait patiently for the master of air quality sensors to chime into this conversation ;) Then we have a few other little conversational discussions to have on here for the other sensors and the 240v powering situation.
Thanks for your input on that last post, i always enjoy our conversations and idea suggestions!
-
@Samuel235 : thx. good choice for hot air gun.
oki, I didn't know you want this node ac powered.
just a last thing..it's a big shortcut to think that analog signals is as easy as a simple resistor divider and read it with adc ;) imho analog is an art like rf. good filtering, opamp theory, mixed signals routing science etc.. I just say this because I'm actually learning and working on this at my job. I need to route a reliable board with lot of adc, digital, there will be can bus.., in harsh environment like car/trucks engine (hopefully for me I work with an analog guy, my dad, old school lol).
Don't worry, I think your board may not need all this care (I hope). it's just some points and so you can learn more. good luck :) -
@Samuel235 : thx. good choice for hot air gun.
oki, I didn't know you want this node ac powered.
just a last thing..it's a big shortcut to think that analog signals is as easy as a simple resistor divider and read it with adc ;) imho analog is an art like rf. good filtering, opamp theory, mixed signals routing science etc.. I just say this because I'm actually learning and working on this at my job. I need to route a reliable board with lot of adc, digital, there will be can bus.., in harsh environment like car/trucks engine (hopefully for me I work with an analog guy, my dad, old school lol).
Don't worry, I think your board may not need all this care (I hope). it's just some points and so you can learn more. good luck :)@scalz, it is a good thing i didn't think it was that simple and why i don't like using that method for the adc of voltage monitoring. From the other topic on here with the voltage monitoring you can see i was having a lot of issues with understanding the theory behind it. I don't like to do something because that is how it needs to be done, i'm the person that actually wants to underatand the reason and method of doing it and why.
Normally, old school is the best way to learn. The new methods are mostly better, but for the method the old school way is better. So thank your father!
I don't think these boards of mine will need the type of intricacies like you're having to do, but i'm always learning the methods and theories on why they need to be done like that.
-
cool, I think you will get this sensor working...even if now you don't need all these advice, maybe in future you will remember about it when needed ;)
humm, maybe at lunch I will try to make a basic and small childboard for this one..so I will be able to add it to my pir multisensors..very tempting, and so I would be able to help you.. -
cool, I think you will get this sensor working...even if now you don't need all these advice, maybe in future you will remember about it when needed ;)
humm, maybe at lunch I will try to make a basic and small childboard for this one..so I will be able to add it to my pir multisensors..very tempting, and so I would be able to help you..@scalz Oh, no doubt about it i need this advice and i thank you for it. I definitely need it as i wouldn't be asking here ;)
From my findings i need a fair bit of help on the sensors them selves and their calibrations too.
A daughter board for which board? I'm intrigued to see what you come up with. I'm planning on having this split in two boards stacked on top of each other inside of the enclosure. One for power distribution and one for data and sensor connections.
-
:+1: Gas/Smoke/Temp/Hum/Light/Motion in one would be great!
For me its tempting when you are aiming at a celing mounter 3d case like a smoke detector.I hope it can all be fitted inside a normal size case - you see, there are other aspects of it like esthetics according to my wife.
-
:+1: Gas/Smoke/Temp/Hum/Light/Motion in one would be great!
For me its tempting when you are aiming at a celing mounter 3d case like a smoke detector.I hope it can all be fitted inside a normal size case - you see, there are other aspects of it like esthetics according to my wife.
@sundberg84, i'm with your wife here. It must look appealing to the eye, hense why i wanted in a custom enclosure fashioned like that smoke detector/sprinkler image i included. Since its something being mounted on the ceiling, its got to be subtle and not in your face ugly.
I'm glad you're very interested in following this production, thank you 👍
-
@sundberg84 nice catch :)
@Samuel235 : this one (I showed you in post above) http://forum.mysensors.org/topic/2951/my-mysx-multisensors-board
On daughter board, the sensor would be on the left side of the pic because others sensors are on right (little dirty hack but like this I could have everything I need per room..depending of the sketch size too). I would add mosfet to cut power on daughterboard etc...a thing to try, I just need to make a tiny daughter board, oshpark and voila! -
@sundberg84 nice catch :)
@Samuel235 : this one (I showed you in post above) http://forum.mysensors.org/topic/2951/my-mysx-multisensors-board
On daughter board, the sensor would be on the left side of the pic because others sensors are on right (little dirty hack but like this I could have everything I need per room..depending of the sketch size too). I would add mosfet to cut power on daughterboard etc...a thing to try, I just need to make a tiny daughter board, oshpark and voila! -
@Samuel235 : here what could look my small childboard...first pass, I will change few things before order it. 3.35$ for 3 boards at oshpark :) It could be smaller, it is because now I like/try to have everything ontop (but there are two smd jumpers on bottom), that made me hungry! time to eat :)
@tbowmo: here an idea for a childboard ;)
-
@Samuel235 : here what could look my small childboard...first pass, I will change few things before order it. 3.35$ for 3 boards at oshpark :) It could be smaller, it is because now I like/try to have everything ontop (but there are two smd jumpers on bottom), that made me hungry! time to eat :)
@tbowmo: here an idea for a childboard ;)
-
@Samuel235 thx. actually, I still use eagle 6.5, I know there are things in 7.x but not tried yet. so for the moment, sometimes I make my own model, or find some where I can..for 3d preview, google sketchup eagleup. So for pcb preview I use sketchup, for custom enclosure solidworks (I prefer it than sketchup) then I export box to sketchup (as I can't do the opposite). Have fun :)
-
@Samuel235 thx. actually, I still use eagle 6.5, I know there are things in 7.x but not tried yet. so for the moment, sometimes I make my own model, or find some where I can..for 3d preview, google sketchup eagleup. So for pcb preview I use sketchup, for custom enclosure solidworks (I prefer it than sketchup) then I export box to sketchup (as I can't do the opposite). Have fun :)
-
Nice :) I'm preparing a board with various sensor types on, that one could populate as one wishes..
