💬 Button size radionode
-
for batt/powering choice, I don't see a consensus lol! I think it really depends on goals and requirements. sometimes sensors can require some voltage, or you want less maintenance+cheaper batt etc.
- lithium AA/AAA (or alkaline but less good), cheap in packs, easy to find and great seldischarge rate. It's 2500-3000mah. Put them in // and you can double your lifetime... if no problem with footprint, you can find cheap LR14, 8000mah, not tried, but wow ;)
- Coincell, lower mah, and very variable lifteime if noname...
And booster is interesting if you control the power consumption of your system, and use an ultra efficient during very light loads.
Then, not sure if cr123 win so easily. CR123 have good selfdicharge rate in primary batt form, and it's something like 1200mah.About the overall size of the device vs batt size etc..because booster takes more component..but when you make a device you don't use only an atmel+radio only.., you need more things, so at the end it's bigger. near the size of an AA/AAA. or use shield board style, but then it's not thin, less nice when using coincell. But I like the format of coincell, that's just not the same league...
Why I say this..because I made some experiments, and have some boards with boosters (not released yet..) and I like the TPS61098x..crazy thing, but very tiny :)
I don't want to debate..just my thought.for rfm69, +1 for interrupts :) and if you want to optimize the power consumption in future with listenmode ;)
-
Can anyone confirm microchip 24LC64 as eeprom (pinout is standard for sot23 eprom, so it is possible to change chip in future)? Is standard library compartible with it? Thanks!
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
I'm revising my earlier comment. Based on new experience, I wouldn't recommend using the smaller atmega328p.
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
@bjornhallberg said:
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
You can find these modules as "rfm69hc" on Ali. Do not forget about haggling :)
I've received new version of these little boards :smiley:
Will show new soldered boards asap. -
Next revision :smirk:
-
Looks perfect with new usb-ttl. :smiley: I plan to use this configuration as RFM69-USB gateway.
-
All my rfm69 boards family are under tests now :smiley:
-
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
@Cliff-Karlsson said:
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
I will try to estimate rough prices for all boards today.
-
So I am ready to present estimated prices to all my new boards.
The estimate is too rough because I am not sure about size of the production batch. But it's better than nothing. Prices include pcb's, components and assembly. Configurations are not fully accepted yet.---WALL SOCKET INSERTABLE NODE
BASIC (ac/dc, atmega, rfm69, 10a relay) - 9.5$
ADVANCED (ac/dc, atmega, rfm69, 10a relay, current sensor, rgb led) - 10.8$
MAX (ac/dc, atmega, rfm69, 10a relay, currrent sensor, atsha204, watchdog, rgb led) - 12.2$---WALL SWITCH INSERTABLE NODE
BASIC (atmega, rfm69, buttons controller, JST wires) - 6.5$
MAX (atmega, rfm69, buttons controller, JST wires, atsha204) - 7.5$--BUTTON SIZE RADIO NODE
BASIC (atmega, rfm69) - 6$
MAX (atmega, rfm69, atsha204) - 7$--SECRET TTL-USB
BASIC - 1.4$ -
Ahh Great, I will be ordering a lot of boards when they are available. Just one question, do you have any sensor-boards planned? like PIR/temp/hum/Lux -multisensor ?
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
