💬 Button size radionode
-
Can anyone confirm microchip 24LC64 as eeprom (pinout is standard for sot23 eprom, so it is possible to change chip in future)? Is standard library compartible with it? Thanks!
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
I'm revising my earlier comment. Based on new experience, I wouldn't recommend using the smaller atmega328p.
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
-
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
@bjornhallberg said:
@Koresh Where do you get the rfm69(h)w rev 3.0 from? Or is it the hc model? I can only seem to find rev 2 (?) on Ali?
You can find these modules as "rfm69hc" on Ali. Do not forget about haggling :)
I've received new version of these little boards :smiley:
Will show new soldered boards asap. -
Next revision :smirk:
-
Looks perfect with new usb-ttl. :smiley: I plan to use this configuration as RFM69-USB gateway.
-
All my rfm69 boards family are under tests now :smiley:
-
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
-
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
@Cliff-Karlsson said:
@Koresh Could you give us a rough estimate of the assembled price for the different nodes?
I will try to estimate rough prices for all boards today.
-
So I am ready to present estimated prices to all my new boards.
The estimate is too rough because I am not sure about size of the production batch. But it's better than nothing. Prices include pcb's, components and assembly. Configurations are not fully accepted yet.---WALL SOCKET INSERTABLE NODE
BASIC (ac/dc, atmega, rfm69, 10a relay) - 9.5$
ADVANCED (ac/dc, atmega, rfm69, 10a relay, current sensor, rgb led) - 10.8$
MAX (ac/dc, atmega, rfm69, 10a relay, currrent sensor, atsha204, watchdog, rgb led) - 12.2$---WALL SWITCH INSERTABLE NODE
BASIC (atmega, rfm69, buttons controller, JST wires) - 6.5$
MAX (atmega, rfm69, buttons controller, JST wires, atsha204) - 7.5$--BUTTON SIZE RADIO NODE
BASIC (atmega, rfm69) - 6$
MAX (atmega, rfm69, atsha204) - 7$--SECRET TTL-USB
BASIC - 1.4$ -
Ahh Great, I will be ordering a lot of boards when they are available. Just one question, do you have any sensor-boards planned? like PIR/temp/hum/Lux -multisensor ?
-
@Koresh I think this eeprom has libs for arduino. but if this is for using ota with dualoptiboot and mysensors, as far as I know, it's not compatible. only jedec spi eeprom for the moment..If it's only for datastorage, I don't see problems.
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
-
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
@Cliff-Karlsson said:
Have you planned to release some kind of general sensor too? Like temp/hum /light/pir?
Unfortunately I have no time. Now i'm focusing on preparing three boards for mass production. Do not forget, I have job and I design those boarsd in my free time. May be I will design sensors boards after :smiley:
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login