Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Switch from serial to ethernet gateway

Dan S. Hero Member 2 Oct 2014, 16:01 last edited by

Am contemplating switching from serial gateway to ethernet. How do I delete the serial gateway stuff from Vera?
Reply Quote 0
1 Reply Last reply
Loading More Posts
3
Posts

1.1k
Views
Reply

Reply as topic
Log in to reply
hek Admin 2 Oct 2014, 16:25 last edited by

You don't delete anything. Just add ip number:port in ip-field (advanced).
Reply Quote 0
1 Reply Last reply 3 Oct 2014, 01:45
Dan S. Hero Member 3 Oct 2014, 01:45 last edited by @hek

@hek Thanks. Should have known better since the instructions are in the Ethernet sketch!
Reply Quote 0
1 Reply Last reply

3
Posts

1.1k
Views

Log in to reply

3 out of 3

Suggested Topics

Vera Edge pi v1 ethernet gateway
Vera • 7 Dec 2019, 13:56 • urbanus 18 Dec 2019, 07:04

10

0
Votes

10
Posts

195
Views

18 Dec 2019, 07:04

@urbanus in your wiring, did you flip around the leds? (i.e. did you connect the longer pin to the gpio pins instead of to vcc? With your wiring, are the leds on when there is no traffic? My guess is that you have reversed the connections. Which is fine, but by default the leds will be on.
Vera/Ezlo
Vera • 9 Jan 2021, 14:13 • r-nox 9 Jan 2021, 14:13

1

0
Votes

1
Posts

21
Views

No one has replied
Issues Reading Sensors in Vera Plus
Vera • 26 Jan 2023, 17:12 • Newzwaver 26 Jan 2023, 17:12

1

0
Votes

1
Posts

7
Views

No one has replied
Vera Plus plugin issues (and choosing the right controller in general)
Vera • 6 Jun 2021, 10:16 • Max Kurilov 6 Jun 2021, 16:55

3

0
Votes

3
Posts

22
Views

6 Jun 2021, 16:55

@nagelc thank you for directing me to the log parser. It helped me to understand that my issue caused by lack of INCLUSION_MODE messages that is easily solved by uncommenting MY_INCLUSION_MODE_FEATURE in my gateway sketch. The second part of the question stays valid. I realize that choosing the "right" controller is much more than choosing the controller that works good with MySensors. Anyway, I appreciate any personal experience on that.
Vera and Moteino USB as Gateway
Vera • 23 Mar 2017, 17:06 • kincaidj001 30 Nov 2021, 16:00

5

0
Votes

5
Posts

2.0k
Views

30 Nov 2021, 16:00

Hello, I realize this is an old thread, but I'm hoping someone can help with the 'tweaks' mentioned above. I followed @blacey 's advise and contacted Vera support. So far they have basically told me to pound sand, stating they don't support third party plug-ins. They did ask for more info about the Motieno VID/PID combo that needs to be recognized though. I responded saying I am only asking for help getting my Vera Edge to recognize a USB device plugged into it and referred them to this thread. They have not responded for several days. Hopefully they will get back to me, but it isn't an encouraging start. They've been very good to me on other issues in the past. Any info on what needs to be changed to get Vera to recognize the Motieno device would be very helpful. As background, I've been running an Arduino Nano-based gateway for several years but my Vera periodically loses the serial port configurations. I've read that is likely due to the nano being a clone so I decided to upgrade to sensebender to tidy things up and hopefully improve reliability. I know I could add an ethernet board and be done with it, but I'd prefer to connect the gateway via serial port if I can get it to work. TIA

1
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1