Mysensors Ethernet GW w5100 problem

mrc-core

arduino with mysensorv version 1.5.4 was the last one i had used and all was working OK.
now i'm truing to use the mysensors 2.0.0 but hav this strange problem.
I don't want to go back to version 1.5.4 and stay on the new version 2.0.0 but i want to still have the ethernet gateway because my gateway is located outside my house for better received all my sensors outside.

Is there any fix for this problem? is this a bug?

? Offline

There seems to be a problem with mysensors 2.0 and the arduino IDE version 1.6.9 and1.6.10.

On the arduino website you can download old versions of the IDE. Try version 1.6.8.

mrc-core

Ok. problem with the arduino IDE fix, i can upload the code without errors thanks Jason37.
But i still have the problem with the ethernet gateway no connecting to domoticz, same error, reconnecting.....

tlpeter

Can you show the sketch?
I succesfully connected a ENC28J60 gateway and connected fine.

mrc-core

@tlpeter
I'm using the sketch that can be found on the test folder from the library 2.0.0

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with 
// radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
  #define MY_SOFTSPI
  #define MY_SOFT_SPI_SCK_PIN 14
  #define MY_SOFT_SPI_MISO_PIN 16
  #define MY_SOFT_SPI_MOSI_PIN 15
#endif  

// When W5100 is connected we have to move CE/CSN pins for NRF radio
#ifndef MY_RF24_CE_PIN 
  #define MY_RF24_CE_PIN 5
#endif
#ifndef MY_RF24_CS_PIN 
  #define MY_RF24_CS_PIN 6
#endif

// Enable to UDP          
//#define MY_USE_UDP

#define MY_IP_ADDRESS 10,8,1,201   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003      

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>

#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensors.h>


void setup()
{
}

void loop() {
}

2016-08-18 11:45:08.681 MySensors: Can not connect to: 10.8.1.201:5003
2016-08-18 11:45:08.681 TCP: Connection problem (Unable to connect to specified IP/Port)
2016-08-18 11:45:08.681 TCP: Reconnecting in 30 seconds...
2016-08-18 11:45:38.687 TCP: Reconnecting...

tlpeter

Can you ping it?

mrc-core

Yes i can, but i can see some lag on the ping today, on the last 2 days this was not happening....
Pinging 10.8.1.201 with 32 bytes of data:
Request timed out.
Reply from 10.8.1.201: bytes=32 time<1ms TTL=128
Request timed out.
Reply from 10.8.1.201: bytes=32 time=1ms TTL=128
Reply from 10.8.1.201: bytes=32 time<1ms TTL=128
Request timed out.
Request timed out.
Request timed out.

mrc-core

Funny now the ping does not have any lag since i hade done a reeboot to the gateway

tlpeter

Can you still ping when it is disconnected? (IP conflict)
Maybe power related?

Anticimex

@mrc-core The sketches under the test folder in the mysensors git (the library) is intended for CI evaluations. They are not examples to be used on target.

mrc-core

@tlpeter Have tryed no ip conflit thats ok

arduino ide debug i get this
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;Starting gateway (RNNGA-, 2.0.0)
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:RADIO:OK
0;255;3;0;9;TSM:GW MODE
0;255;3;0;9;TSM:READY
IP: 10.8.1.201
0;255;3;0;9;No registration required
0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55
0;255;3;0;9;TSP:MSG:READ 5-5-0 s=9,c=1,t=14,pt=2,l=2,sg=0:55

mrc-core

@Anticimex so i have to get my old code and remake it with the code from sensors 2.0.0

Anticimex

@mrc-core Examples have moved to a different repo: https://github.com/mysensors/MySensorsArduinoExamples

mrc-core

@Anticimex Thanks going to see yhe examples and tried to fix this problem.

mrc-core

I'm getting this error on IDE

:\Users\marco\Documents\Arduino\libraries\MySensors/MySensors.h:233:5: error: #error UDP mode is not available for ENC28J60

#error UDP mode is not available for ENC28J60

Yveaux

@mrc-core I think the error is quite clear : you enabled UDP which is not supported in combination with ENC

mfalkvidd

@mrc-core I found this comment in an old version of the code:

 #undef MY_USE_UDP // Will not fit (or compile) on ENC28J60

So it seems the problem is what the message says, UDP doesn't work on ENC28J60.
@hek might know more

hek

Yeah, had to reduce the ENC lib to a minimum to make it compile with MySensors. But it was a couple of years ago. Haven't got the bandwidth to test it now.

mrc-core

How did tlpeter got it to work ?
What can i do? Go back to the w5100? At this moment i dont have nothing working at home.

mrc-core

@tlpeter can you upload your working sketch

Mysensors Ethernet GW w5100 problem

10

11.7k

11.2k

113.1k