💬 Building a Raspberry Pi Gateway

engy

Hello Masters,

Could you please help me with setting up virtual serial port?

I can't see the interface created under /dev.
I'm using the instructions and finish with the setup with the following command:

pi@raspberrypi:/tmp/MySensors $ ./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2836, Type=Rpi2, CPU=armv7l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

pi@raspberrypi:/ $ sudo /usr/local/bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

Everything seems to be OK. However, when I check /dev directory, the interface is not created.

What could be an issue?
Thank you in advacne!

gohan

Why don't you compile it as ethernet gateway?

engy

@gohan Etherner Gareway is not supported by OpenHab MySensors binding.

gohan

Mqtt? 😀

engy

@gohan I'm sorry, MQTT is not supported by OpenHab MySensors binding. Ethernet Gateway is not supported on Raspberry PI.

marceloaqno

@engy OpenHab2 supports mysensors serial and ethernet gateways:
https://github.com/tobof/openhab2-addons/wiki

Maybe the build guide may have given you that impression, but ethernet Gateway is supported on Raspberry PI:

./configure --my-gateway=ethernet

keldandorin

@gohan Solved the problem with radio...Thx

engy

Thank you guys for prompt reaction. Indeed, Ethernet GW works flawlessly!

TommiP

Hi
Is anyone else having this same problem on Rpi3?: Gateway works ok after "sudo make install" with openHAB. With "sudo ./bin/mysgw -d" I can get debug log visible and log works ok.
But if I run "sudo systemctl enable mysgw.service" after "sudo make install", debug log start showing endlessly "mysgw: accept: Bad file descriptor". So debug log function gets destroyed and it can't be used anymore. I have made several clean installations and every time this same happens.
Br
Tommi

marceloaqno

@TommiP What I think is happening is that you are running two instances of the gateway.
If you need to get the debug logs, first stop the mysgw service:

sudo systemctl stop mysgw.service

TommiP

@marceloaqno
Ok, now I understand what happened, thanks.

romeo01

Re: 💬 Building a Raspberry Pi Gateway

Silly questions, I'm a little bit confuse.
I have a serial Gateway running with arduino nano + nrf24 and a raspberry pi with domoticz on board. The link between domoticz & Gateway is done via USB <=> serial port (/dev/ttyUSB0). This setup runs like a charm.

Now, I would like to access to my Gateway via the network because I would like to use "Over The Air " functionnality with MYSController.

Can I install MySensors Gateway on the raspberry and keep the arduino + nrf24 connected via usb ?? For the moment, I can not use GPIO port.

If for some reason you can't use the GPIO pins of the Raspberry Pi, you could connect the radio to a arduino with the GatewaySerial sketch and feed the pi through a serial port:

./configure --my-gateway=serial --my-serial-port=/dev/ttyUSB0 --my-serial-baudrate=115200

[SECTION] Detecting target machine.
[OK] machine detected: SoC=BCM2836, Type=RPi3, CPU=armv7l.
[SECTION] Detecting SPI driver.
[OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
[OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

make

./bin/mysgw -d

mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=2
mysgw: TSM:FAIL:PDT

Where is my mistake ??
Again, Can I install MySensors Gateway on the raspberry and keep the arduino + nrf24 connected via usb or I must connected the nrf24 directly with GPIO on the Rasp ??

Thanks in advance for your reply.
Romeo

gohan

@romeo01 I think that connecting nrf24 directly to arduino and compile mysgw as ethernet gateway is the cleanest solution (I have it as MQTT and it is working fine, but ethernet is the same). Keep in mind that you'd better use one of those adapters 5v-3.3v for nrf24 chips + capacitor because the 3v output of raspberry isn't very suited for the task.

romeo01

Thanks gohan for fast answer.

Arduino nano + nrf24 are already connected together. Hardware is already built.

How access to the gatway installed on the raspberry via the network and use my arduino + nrf24 connected via usb/serial to the raspberry ??

Sorry but I do not understand what you mean
...compile mysgw as ethernet gateway is the cleanest solution...

If I configure on this way
./configure --my-gateway=ethernet --my-port=5003

I could access to my Gateway via network an the Gateway will use the arduino + nrf24l via usb/serial ??

That's why I say I'm confuse.

--my-gateway=serial

What is this option ? The link between gateway and nrf24 or the way to access to the Gateway ??

romeo01

In summary,

Is the Gateway (software) installed on the raspberry, is able to manage the nrf24 connected on arduino via USB/Serial port ??

gohan

no, I don't think so. If you want to manage nodes over network you need to make an ethernet gateway (could be a UNO with w5100 shield, an esp8266 or mysgw compiled on raspberry)

romeo01

nrf24 connected to a arduino nano and plugged to the raspberry over the usb/serial cable is not considered as a serial device ?

What is this option ?

--my-gateway=serial

If for some reason you can't use the GPIO pins of the Raspberry Pi, you could connect the radio to a arduino with the GatewaySerial sketch and feed the pi through a serial port:

That's exactly what I need, but how to do ??

./configure --my-gateway=serial --my-serial-port=/dev/ttyUSB0 --my-serial-baudrate=115200

Serial port /dev/ttyUSB0 is ok, because I use this with domoticz and it'running good.

My initial question is how to use my old gatway (arduino + nrf24) with the gateway compiled on the raspberry over the usb/serial cable ?
I can not use GPIO port.

gohan

The serial gateway on the raspberry does what your nano is doing and you can't have gateways talking to each other. Maybe you could look at mycontroller and see if can manage nodes the way you want.

dirkc

When talking about this Raspberry Pi Gateway, I suppose, that its just connecting the NFR24L01+ to the Raspberry Pi GPIO and run

./bin/mysgw -d

right? On my Pi it does not work this way, maybe the NFR24L01+ is not ok. Instead I am running an external esp-wifi-gateway, but a direct gateway seems the better solution to me.
So did I get it right, that I can use a NFR24L01+ connected to the Raspberry PI GPIO without any external gateway? If so, what are the parameters for building the mysgw daemon? I tried this one:

./configure --spi-driver=SPIDEV --spi-spidev-device=/dev/spidev0.0

update: as in https://www.mysensors.org/view/180#wiring
22 – CE
24 – CSN/CS
23 – SCK
19 – MOSI
21 – MISO

SPI is activated:

$ls /dev/spidev*
/dev/spidev0.0  /dev/spidev0.1

And this is the result, when building it with the settings mentioned above. (Raspberry Pi 3, jessie 4.9.13-v7+)

$ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=2
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=3
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=4
mysgw: TSM:FAIL:PDT

And can someone show how to bind this gateway into FHEM? As said, today I am running an esp-wifi-gateay.

Thanks in advance for any support...

romeo01

@gohan
With the serial Gateway on the raspberry; how is connected the nfr24 ??
If usb/serial port is no possible, which serial port to use ?

💬 Building a Raspberry Pi Gateway

14

11.7k

11.2k

113.0k