💬 Relay

[Efflon]

@Boots33 Ok, you explanation is what was my only explanation to the "missing" code. When experimenting with this using the mqtt gateway sketch and home-assistant as controller, the ACK is just an ACK and not a "real" message with payload thus just toggling the state bool and getting things out of sync..

[Woeka]

I did not get the example working properly with my 8 channel SSR. So here is my updated version of the example.

I have changed the way the pins are assigned by using a array. The current example tries to connect relays 7 and 8 to pins 9 and 10 when you select an 8 channel relays. This won't work because those pins are used by the radio module.

I think you can connect a relays to any pin which is not used. If so this will make it possible to connect up to 14 relays to the mini pro when also the pins A5-A7 are available.

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>

const int PINS[] = {3, 4, 5, 6, 7, 8, 14, 15}; // I/O pins 3, 4, 5, 6, 7, 8, A0, A1 for the relays 
#define NUMBER_OF_RELAYS 8 // Total number of attached relays
#define RELAY_ON 0  // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay


void before()
{
    for (int sensor=1; sensor<=NUMBER_OF_RELAYS; sensor++) {
        // Then set relay pins in output mode
        pinMode(PINS[sensor-1], OUTPUT);
        // Set relay to last known state (using eeprom storage)
        digitalWrite(PINS[sensor-1], loadState(sensor)?RELAY_ON:RELAY_OFF);
        
    }
}

void setup()
{

}

void presentation()
{
    // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Relay", "1.0");

    for (int sensor=1; sensor<=NUMBER_OF_RELAYS; sensor++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_BINARY);
    }
}


void loop()
{

}

void receive(const MyMessage &message)
{
    // We only expect one type of message from controller. But we better check anyway.
    if (message.type==V_STATUS) {
        // Change relay state
        digitalWrite(PINS[message.sensor-1], message.getBool()?RELAY_ON:RELAY_OFF);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        // Write some debug info
        Serial.print("Incoming change for sensor:");
        Serial.print(message.sensor);
        Serial.print(", New status: ");
        Serial.println(message.getBool());
    }
}

[Samuel235]

I'm attempting to get my double relay board containing two switch inputs. I see that the two sketches suggested on the relay page are there but one seems to be updated to the new version which allows you to use multiple relays on the board but the other isn't, as far as i can see. How do I go about making the sketch with buttons accept more relays?

[ijobain]

Hi @Woeka
I've been testing your code, but works inverse mode
if switch in domoticz is on the relay is off and vice versa

[Boots33]

@ijobain Try changing

#define RELAY_ON 0  // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay

To

#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

and see if that works as you expected

[Boots33]

@Samuel235 Have a look at this thread for some ideas.

[ijobain]

@Boots33
Thank you so much
I am newbie

[Samuel235]

@Boots33 - Thanks dude, I have had a quick skim read just but will bookmark it when i get my gateway working. These issues right now are driving me insane, and spending the day to try and find the problem. Thank you for linking me to that post!

[Rene046]

I just tried this sketch, works on latest version, but i cant seen any relais in Domoticz, only see the node relais, did i miss something

[HenryWhite]

@Rene046 you could try my sketch: https://forum.mysensors.org/topic/6638/multiple-relays-motion-sketch-fully-customizable-optional-timer-manual-override

[Rene046]

@HenryWhite

thx

[sineverba]

Hi to all!
I would edit the secure relay sketch so in loop the node sends to the gateway, let's say every hours, his state (on or off).

1. I avoid delay otherwise Arduino cannot receive the comands from gateway, so I will use the millis sketch, modified from the official Arduino website.

My doubt is... How can I get the current state of the relay?

Relevant part of sketch is in loop and before setup()

/* TIME variables */
unsigned long previousMillis = 0;        // will store last time state is sent
// constants won't change:
const long interval = 10000;           // interval at which to send state (milliseconds === seconds x 1000). For test we try every 10 seconds

And the main loop

void loop()
{

  // check to see if it's time to send state; that is, if the difference
  // between the current time and last time you sent state is bigger than
  // the interval at which you want to send the state.
  unsigned long currentMillis = millis();

  if (currentMillis - previousMillis >= interval) {
    // save the last time you blinked the LED
    previousMillis = currentMillis;

    // send the state here!
    // test
    Serial.println("This is the moment where I need to send state");

    //send(?????????); // Send current state. Probabily will update also the log?
  }

The base sketch is >>> https://github.com/mysensors/MySensors/blob/master/examples/SecureActuator/SecureActuator.ino

And the millis example is >>> https://www.arduino.cc/en/Tutorial/BlinkWithoutDelay

Thank you to all!

[sineverba]

@sineverba
Edit:
I did edit the pre-setup configuration

int val = 0;  // the value of digital pin
#define CHILD_ID 1   // Id of the sensor child
MyMessage msg(CHILD_ID,V_LIGHT);

And I did edit the loop:

if (currentMillis - previousMillis >= interval) {
    // save the last time you blinked the LED
    previousMillis = currentMillis;

    // send the state here!
    // test
    Serial.println("This is the moment where I need to send state");

    val = digitalRead(LOCK_1);

    
    Serial.print("Il valore del relay è ");
    Serial.println(val);

    send(msg.set(val),true); // Send new state and request ack back. 
  }

I got the update in Domoticz in Hardware > Configuration > Children of nodes

And I did test also every 3 seconds, all ok.

But I don't have the refresh in "main page":

I did test removing current to Arduino when Relay was ON. With Arduino off, I did change the state in domoticz to OFF.

Because Arduino save previous state in EEPROM, after full start the relay did go ON, in Domoticz got "1" in children (all right, because digitalRead was 1) but main panel shows OFF.

I did expect a graphical change...

Thank you (and hope that all is clear) :)

[sineverba]

Hi to all!
To achieve my goal (node that sends relay state after power failure to sync with domoticz), I'm editing the button script.

I have added this line

state = digitalRead(RELAY_PIN);
send(msg.set(state?false:true), true); // Send new state and request ack back

in setup, so I thought it send only one time at startup the current state after power failure.

But..... the relay shutdown/shuton (or viceversa) twice, in fast sequence....

Thank you very much!

[sineverba]

@sineverba

Bingo!

If I did understand well, the actuator sketch DOESN'T directly acts the relay, but sends to the gateway and expect from the gw itself the "new state" (in effect, you short GND & PIN 4, arduino sends new state to the gateway and gateway resend the new state).

So, 'cause I would to update the state on controller, I did this simple edit on setup:

// Set relay to last known state (using eeprom storage) 
 state = loadState(CHILD_ID);
 digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);

 Serial.print("Lo stato ultimo era ");
 Serial.println(state);

 if ( state == 1) {
   state = 0;
 } else {
   state = 1;
 }
 
 send(msg.set(state?false:true), true); // Send new state and request ack back

Basically, If relay was OFF on a power failure, and someone on Domoticz try to start the relay, the state in Domoticz will be "on".

When power returns, the arduino read the state (in my example OFF == 0), convert in 1 and send to the gateway the 1. The gateway // Domoticz will be answer with 0.

So, relay doesn't nothing and Domoticz state is update.

But.... why I need to invert the logic? :D

[Boots33]

@sineverba said in 💬 Relay:

To achieve my goal (node that sends relay state after power failure to sync with domoticz)

Have a look at the sketch I used for my Synchronising Light switch you may be able to use some of that code perhaps.

[sineverba]

@Boots33

Never seen the request function.
You are hero-member for a reason...
Thank you very much! :) :)

[Boots33]

@sineverba said in 💬 Relay:

Never seen the request function.

You can find request and other useful info on the API page.
Hope you are enjoying your MySensors journey :)

[fhenryco]

Hello,

since the relay has leds and is therefore power consuming, i was wondering if someone has written a sketch for a low power usage of the relay (as for the sensors) allowing the arduino (and the relay) to sleep all the time and wake up every 5 minutes for instance just to check if the controller has changed the desired state of the switch.

Of course then the relay could be as late as 5minute, but this is not an issue for my application ...

thanks for any suggestion

[mfalkvidd]

@fhenryco can't the relay node use power from whatever it is controlling?

For sleeping nodes, the smartsleep feature can be useful. Search for that keyword in the forum and look at https://www.mysensors.org/download/sensor_api_20#sleeping