💬 Temperature Sensor

[bentrik]

It seems the DallasTempereture library is not a part of the default Library setup from Mysensors as of version 2.0? I tried to compile the above code, but I had to manually download DallasTemperature from GitHub first. Then OneWire was also missing. Adding these two libraries brought me a bit further, but I get a long list of errors connected to OneWire. What libraries should be used?

[mfalkvidd]

@bentrik the library is part of the MySensorsArduinoExamples, which can be downloaded at https://github.com/mysensors/MySensorsArduinoExamples/archive/master.zip

[Sealander]

Hi All, i'm also new here and into this. Like others i also ran into problems compiling this sketch, i tried al libraries mentioned in the posts in this thread, but no go. keep getting this error message:

In file included from C:\Users\Gebruiker\Desktop\My Sensors\MySensors-master\MySensorsArduinoExamples-master\examples\DallasTemperatureSensor\DallasTemperatureSensor.ino:37:0:

C:\Users\Gebruiker\Documents\Arduino\libraries\DallasTemperature/DallasTemperature.h: In function 'void loop()':

C:\Users\Gebruiker\Documents\Arduino\libraries\DallasTemperature/DallasTemperature.h:252:13: error: 'int16_t DallasTemperature::millisToWaitForConversion(uint8_t)' is private

 int16_t millisToWaitForConversion(uint8_t);
         ^

DallasTemperatureSensor:85: error: within this context

int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());

      exit status 1

within this context

Can someone help me with this problem? i have no clue at all and woud really like to build me a working sensor so i can hook it up to my Domoticz setup. thanks

hin this context

[stingone]

@Sealander

see solution above. Delete your dallas library and replace with the one above in the master zip file. That was the solution for me.

[bentrik]

@mfalkvidd Thanks for the feedback, It got me a bit further.
I have a fresh Windows Arduino 1.6.12 install, and I have download the MySensors Library 2.0 through the Library manager, and I've found MySensors.h and MyConfig.h under \Documents\Arduino\libraries\MySensors

I'm able to compile and upload the RelayActuator but quite a few of the library files seem to be missing in 2.0. DallasTemperature seem to be one of them.-But I struggled with DallasTemperature and some others.

I copied all the whole MySensors-1.5.4.zip library files to to C:\Program Files (x86)\Arduino\libraries, and I managed to compile, but I got an error message saying Invalid version found: 1.04
Then I tried to only copy the DallasTemperature and OneWire folder, and I had no errors.

-So I assume all library files the entire MySensors Examples catalouge are not ready in Libraries 2.0.

Anyways: The solution to get this sensor to work with Arduino 1.6.12, following the Download and API guide, adding MySensors 2.0 through the Library Manager, is to manually add:
\Arduino\libraries\DallasTemperature
\Arduino\libraries\OneWire\

-from https://github.com/mysensors/MySensorsArduinoExamples/archive/master.zip
-And not adding the whole structure.

Now I just have to find out how to make it speak to my serial gateway :satisfied:

[wendan]

I get the feeling it is possible to use more then one sensor parallel on port 3. I wonder if each sensor is being monitored? Am I right and do I need to alter or change something?

[wendan]

my feeling was right.... i just connected 5 temp censors it is working great

[Joseph Absher]

I am getting the error:

DallasTemperatureSensor.ino: In function 'void loop()':
DallasTemperatureSensor:93: error: 'getConfig' was not declared in this scope
     float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

Does anyone have any suggestions?

[mfalkvidd]

@Joseph-Absher https://forum.mysensors.org/topic/5841/getconfig-was-not-declared-in-this-scope-v2-1-1-fixed

[Joseph Absher]

@mfalkvidd That worked. Thanks.

[Vincent Lgrd]

Hello,
I'm a beginner in home automation and I'm trying MySensor for the first time. My acctual configaration is a Domoticz on a Raspberry Pi 2B and a RFLink GW with a NRF24L01 module to try to measure with a MySensor probe.
I've building a temperature sensor with a DS18B20 sensor on a Official Arduino nano board and I can not run the sensor correctly.
The arduino serial monitor show these:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
12 TSM:FPAR
15 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2022 !TSM:FPAR:NO REPLY
2024 TSM:FPAR
2026 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4034 !TSM:FPAR:NO REPLY
4036 TSM:FPAR
4038 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6046 !TSM:FPAR:NO REPLY
6048 TSM:FPAR
6050 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8058 !TSM:FPAR:FAIL
8059 TSM:FAIL:CNT=1
8061 TSM:FAIL:PDT

Someone could help me?

[gohan]

Did you set node ID?

[Vincent Lgrd]

Where should I put it? In arduino sensor code?

[gohan]

Yes, it's like #define MY_NODE_ID 2 and put it at beginning of the code

[Vincent Lgrd]

Ok , with Node ID, I have this:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 MCO:BGN:BFR
63 TSM:INIT
64 TSF:WUR:MS=0
71 TSM:INIT:TSP OK
73 TSM:INIT:STATID=2
75 TSF:SID:OK,ID=2
76 TSM:FPAR
113 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2120 !TSM:FPAR:NO REPLY
2122 TSM:FPAR
2158 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4166 !TSM:FPAR:NO REPLY
4168 TSM:FPAR
4204 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6212 !TSM:FPAR:NO REPLY
6214 TSM:FPAR
6250 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8258 !TSM:FPAR:FAIL
8259 TSM:FAIL:CNT=1

[gohan]

ok, but we are going off topic since now your problem seems to be the radios can't talk to each other, so if you take a look in troubleshooting section you will see others having this error that usually if bad wiring, missing capacitor on vcc of the nrf24, range/interference problem. How far are the 2 radio modules? Try putting them 2-3 meters apart.

[Vincent Lgrd]

Thanks, my radio modules are very close, they are on the same table for test. On of them may be damaged, I must receive others. I'm going in the troubleshooting section to avoid polluting this article.
Thanks for your help

[gohan]

Put them at least 2 meters apart, just to play safe.

[Vincent Lgrd]

It's the same, I've even reversed the radio modules

[dantefff]

@gohan , I'm in the same situation as @Vincent-Lgrd. I'm powering my arduino UNO from usb (to test). Is that a possible problem?