💬 Sensebender Micro mk2
-
-
Hello, tbowmo
I'm new to mysensors and home automation and this board is exactly what I was looking for, great job !
Have you received prototypes? Do you plan to sell it ?
And what about using SAML instead of SAMD for ULP nodes? Would it be supported by Mysensors?
Thank you for sharing! -
"Temperature / Humidity sensor Si7021" is listed as an enhancement but the mk1 had the same sensor correct?
-
"Temperature / Humidity sensor Si7021" is listed as an enhancement but the mk1 had the same sensor correct?
-
Right, my mistake.. :) both flash and si7021 is borrowed from mk1..
@Ptibu
I haven't ordered any prototype pcb yet. I'm trying to keep prices down, and SAML is still pretty expensive, compared to SAMD.@tbowmo
Another big advantage of the SAML over the SAMD is the embedded AES core. It would allow strong crypto for both comm & data encryption (at MCU level, not radio) and authentication (ex: AES based CMAC). In this case, the ATSHA is not needed anymore for auth but it will break compatibility with existing ATSHA based boards (unless implementing SHA256 in SW).
For what I can see, cost for SAML is about the same than SAMD + ATSHA (+/- 0.5€).For new (secured) mysensors networks, SAML would have nice advantages with comparable price (+dev efforts of course).
-
@Ptibu
I'm also using some custom atsamd boards on my side. I looked a while ago at SAML. They have some some common points, but if i remember SAML datasheet, it's not completely the same, especially for low power modes, additional features etc.. Is SAML Arduino compatible now? i'm just curious, i don't really need it as there are already so much other great mcu or complete module :) -
@Ptibu
I'm also using some custom atsamd boards on my side. I looked a while ago at SAML. They have some some common points, but if i remember SAML datasheet, it's not completely the same, especially for low power modes, additional features etc.. Is SAML Arduino compatible now? i'm just curious, i don't really need it as there are already so much other great mcu or complete module :)@scalz said:
Is SAML Arduino compatible now?
Not yet. but it is WIP
https://github.com/arduino/arduino-builder/issues/176#issuecomment-269110984@Cliff-Karlsson said:
Is there any site where you can upload the pcb+bom and have all the components (maybe not radio and pinheaders) soldered before they send the pcb?
It is called PCBA service. dirtypcbs and itead have such services.
Got price estimation from itead few weeks ago for this board: about 550$ / 10 boards, including PCD ~100$, stencil ~60$, components ~219$ and assembly ~150$) -
Is there any site where you can upload the pcb+bom and have all the components (maybe not radio and pinheaders) soldered before they send the pcb?
-
Just checked mouser prices, for 100 units:
ATSAML21E18B-AUT : 519,0$
ATSAMD20E18A-AUT : 298,0$
ATSHA204A-STUCZ-T : 83,7$
total : 381,7$price difference: 137,3$ for 100 boards, or 1.37$ per board. So we can still save a couple of bucks by using atsamd + atsha204
-
Just checked mouser prices, for 100 units:
ATSAML21E18B-AUT : 519,0$
ATSAMD20E18A-AUT : 298,0$
ATSHA204A-STUCZ-T : 83,7$
total : 381,7$price difference: 137,3$ for 100 boards, or 1.37$ per board. So we can still save a couple of bucks by using atsamd + atsha204
-
I'm always looking at larger quantities when designing boards :).. Specially when designing the sensebender boards, if we can lower the price just a little it means cheaper boards for the community, or a bit more contribution to the site maintenance etc.
-
Any progress on the mk2?
-
I've got the first prototype pcbs for it.. So just need to get components and assemble the first sample. However, the wife thinks that a new chicken coop (which will be filled with sensors :D) , and various other projects, have higher priority :).
-
Is this board using the RFM69HCW footprint so that one could also use an RFM95??
If not, please consider this change and you might want to consider as an option for DIO-1 connected to an I/O pin on the CPU.. (this would also make it compatible with LoRaWan network)Thanks
-
Is this board using the RFM69HCW footprint so that one could also use an RFM95??
If not, please consider this change and you might want to consider as an option for DIO-1 connected to an I/O pin on the CPU.. (this would also make it compatible with LoRaWan network)Thanks
-
Both the RFM69HC and RFM69HCW are available in the smaller package.... again, this would allow RFM95 to be used.
Thanks...
[0_1496601875842_RFM69HC_DataSheet_v1.1.pdf](/assets/uploads/files/1496601877634-rfm69hc_datasheet_v1.1.pdf) -
Yes, The H = High Power version, C = Compact version 16x16mm pkg, vis 16x19mm pkg
My error, RFM69CW and RFM69HCW are available, also note that if you do not use the power over +13dbm, power consumption is about the same between the radios.
https://lowpowerlab.com/forum/rf-range-antennas-rfm69-library/rfm69w-and-rfm69hw-current-consumption/ [0_1496604219131_RFM69CW-V1.1.pdf](/assets/uploads/files/1496604221362-rfm69cw-v1.1.pdf)
