MYSBootloader 1.3.0-beta.3

[Werwolfx]

@tekka If i ENABLE #define MY_OTA_FIRMWARE_FEATURE
i see ST_FIRMWARE_CONFIG_REQUEST in MYSCONTROLLER logs!!!
if i DISABLE //#define MY_OTA_FIRMWARE_FEATURE msg not in log

i not have external flash/

402	14.01.2017 21:29:28	TX	4 - Water Meter	N/A	C_INTERNAL	NO	I_REBOOT	0
403	14.01.2017 21:29:28	RX	4	1	C_REQ	NO	V_VAR1	
408	14.01.2017 21:29:34	RX	4	INTERNAL	C_STREAM	NO	ST_FIRMWARE_CONFIG_REQUEST	FFFFFFFF48044E100300
409	14.01.2017 21:29:34	TX	4	N/A	C_STREAM	NO	ST_FIRMWARE_CONFIG_RESPONSE	0A0001005000D446
410	14.01.2017 21:29:34	RX	4	INTERNAL	C_PRESENTATION	NO	S_ARDUINO_NODE	2.1.0
411	14.01.2017 21:29:34	RX	4	INTERNAL	C_INTERNAL	NO	I_CONFIG	0
412	14.01.2017 21:29:34	TX	4	INTERNAL	C_INTERNAL	NO	I_CONFIG	M
414	14.01.2017 21:29:34	RX	4 - Water Meter	INTERNAL	C_INTERNAL	NO	I_SKETCH_NAME	Water Meter
417	14.01.2017 21:29:34	RX	4 - Water Meter	INTERNAL	C_INTERNAL	NO	I_SKETCH_VERSION	1.1
419	14.01.2017 21:29:34	RX	4 - Water Meter	1 - S_WATER	C_PRESENTATION	NO	S_WATER	

i load this HEX
load from Arduino IDE 1.8.0
0_1484418874223_MYSBootloader.hex

board.txt

proMYSBL.bootloader.tool=avrdude
proMYSBL.bootloader.low_fuses=0xFF
proMYSBL.bootloader.high_fuses=0xDA
proMYSBL.bootloader.extended_fuses=0xFE
proMYSBL.bootloader.unlock_bits=0x3F
proMYSBL.bootloader.lock_bits=0x0F
proMYSBL.bootloader.file=MySensors/MYSBootloader.hex

[tekka]

@Werwolfx Ok, seems like you also upload the sketch via USBasp thereby erasing/overwriting the bootloader. Try uploading the sketch via serial or OTA after flashing the bootloader.

[Mark Swift]

@tekka am I correct in thinking the HEX found on Github can be used with all Arduino's? I noticed my old folder has one hex for 16, 8 and 1Mhz?

I'm using this board.txt

menu.cpu=Processor

##############################################################

MYSBL13.name=MYS Bootloader - atmega328p

MYSBL13.upload.tool=arduino:avrdude
MYSBL13.upload.protocol=arduino
MYSBL13.upload.maximum_size=30720
MYSBL13.upload.maximum_data_size=2048

MYSBL13.bootloader.tool=arduino:avrdude
MYSBL13.bootloader.unlock_bits=0x3F
MYSBL13.bootloader.lock_bits=0x0F

MYSBL13.build.mcu=atmega328p
MYSBL13.build.board=AVR_PRO
MYSBL13.build.core=arduino:arduino
MYSBL13.build.variant=arduino:standard

## -------------------------------------------------

MYSBL13.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8)
MYSBL13.menu.cpu.16MHzatmega328.upload.speed=115200
MYSBL13.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
MYSBL13.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

MYSBL13.menu.cpu.8MHzatmega328=ATmega328 8MHz (RC, BOD1V8)
MYSBL13.menu.cpu.8MHzatmega328.upload.speed=38400
MYSBL13.menu.cpu.8MHzatmega328.bootloader.low_fuses=0xE2
MYSBL13.menu.cpu.8MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.8MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.8MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.8MHzatmega328.build.f_cpu=8000000L

MYSBL13.menu.cpu.1MHzatmega328=ATmega328 1MHz (RC/8, BOD1V8)
MYSBL13.menu.cpu.1MHzatmega328.upload.speed=9600
MYSBL13.menu.cpu.1MHzatmega328.bootloader.low_fuses=0x62
MYSBL13.menu.cpu.1MHzatmega328.bootloader.high_fuses=0xDA
MYSBL13.menu.cpu.1MHzatmega328.bootloader.extended_fuses=0x06
MYSBL13.menu.cpu.1MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader.hex
MYSBL13.menu.cpu.1MHzatmega328.build.f_cpu=1000000L```

[Mark Swift]

I guess not... The old hex for 8Mhz works, but the one from this thread does not... :(

I'm trying to upload this to my Pro Mini, does anyone have an 8Mhz that works?

[Mark Swift]

@tekka I've noticed some odd things with my nodes when running the bootloader.

To test I uploaded a simple count time sketch. When running the MYS bootloader the timer resets every 10 seconds, see:

Time: 999
Time: 2000
Time: 3000
Time: 4001
Time: 5001
Time: 6002
Time: 7004
Time: 8003
Time: 9005
Time: 0
Time: 999
Time: 2000
Time: 3000
Time: 4001
Time: 5001
Time: 6002
Time: 7004
Time: 8003
Time: 9005
Time: 0

Using the stock Pro Mim 8Mhz 3.3v bootloader it works fine, any ideas?
Perhaps this is because I'm testing using a non-MySensors sketch?

[tekka]

@Mark-Swift yeah, this is intended behavior: the watchdog kicks in after ~8s, so either you reset it in loop() or disable it in setup().

[rmtucker]

Is there a version or branch of this for the rfm69?

[tekka]

@rmtucker No, but everybody is welcome to contribute and enhance the functionality.

[Mark Swift]

@tekka, I'm trying to compile the HEX using OSX. I have installed avr-gcc with homebrew but I get

rm *.o
rm: *.o: No such file or directory
make: [clean] Error 1 (ignored)
rm *.elf
rm: *.elf: No such file or directory
make: [clean] Error 1 (ignored)
rm *.hex
rm: *.hex: No such file or directory
make: [clean] Error 1 (ignored)
"avr-gcc" -funsigned-char -funsigned-bitfields -DF_CPU=16000000L -Os -ffunction-sections -fdata-sections -fpack-struct -fshort-enums -mrelax -Wall -Wextra -Wundef -pedantic -mmcu=atmega328p -c -std=gnu99 -MD -MP -MF "MYSBootloader.d" -MT"MYSBootloader.d" -MT"MYSBootloader.o" -I MYSBootloader.c -o MYSBootloader.o
avr-gcc: fatal error: no input files
compilation terminated.
make: *** [MYSBootloader.o] Error 1

When issueing the Make command, can you help, any suggestions?

[tekka]

@Mark-Swift I haven't tested that with OSX - maybe somebody can help here?

[Mark Swift]

@tekka, started a windows VM, run via MinGW and got this when running makefile, does it look okay?

C:\MySensorsBootloaderRF24-development>mingw32-make.exe
rm *.o
process_begin: CreateProcess(NULL, rm *.o, ...) failed.
make (e=2): The system cannot find the file specified.
Makefile:40: recipe for target 'clean' failed
mingw32-make.exe: [clean] Error 2 (ignored)
rm *.elf
process_begin: CreateProcess(NULL, rm *.elf, ...) failed.
make (e=2): The system cannot find the file specified.
Makefile:40: recipe for target 'clean' failed
mingw32-make.exe: [clean] Error 2 (ignored)
rm *.hex
process_begin: CreateProcess(NULL, rm *.hex, ...) failed.
make (e=2): The system cannot find the file specified.
Makefile:40: recipe for target 'clean' failed
mingw32-make.exe: [clean] Error 2 (ignored)
"C:/Arduino/hardware/tools/avr/bin/avr-gcc" -funsigned-char -funsigned-bitfields
 -DF_CPU=16000000L -Os -ffunction-sections -fdata-sections -fpack-struct -fshort
-enums -mrelax -Wall -Wextra -Wundef -pedantic -mmcu=atmega328p -c -std=gnu99 -M
D -MP -MF "MYSBootloader.d" -MT"MYSBootloader.d" -MT"MYSBootloader.o"  -IC:/Ardu
ino/hardware/tools/avr/avr/include/avr MYSBootloader.c -o MYSBootloader.o
In file included from Core.h:40:0,
                 from MYSBootloader.c:69:
HW.h:51:2: warning: #warning is a GCC extension
 #warning BAUD_RATE error greater than 2%
  ^
HW.h:51:2: warning: #warning BAUD_RATE error greater than 2% [-Wcpp]
In file included from Core.h:42:0,
                 from MYSBootloader.c:69:
MyMessage.h:292:3: warning: ISO C99 doesn't support unnamed structs/unions [-Wpe
dantic]
  };
   ^
"C:/Arduino/hardware/tools/avr/bin/avr-gcc" -nostartfiles -Wl,-s -Wl,-static -Wl
,-Map=".map" -Wl,--start-group -Wl,--end-group -Wl,--gc-sections -mrelax -Wl,-se
ction-start=.text=0x7800 -mmcu=atmega328p   -o MYSBootloader.elf MYSBootloader.o
 -lm
"C:/Arduino/hardware/tools/avr/bin/avr-objcopy" -O ihex -R .eeprom MYSBootloader
.elf MYSBootloader.hex
"C:/Arduino/hardware/tools/avr/bin/avr-size" MYSBootloader.elf
   text    data     bss     dec     hex filename
   2036       6      72    2114     842 MYSBootloader.elf

[Mark Swift]

@tekka Just wanted to check if the above log looks okay, currently rolling the bootloader out to 14 nodes (painful process!) and wanted to check if it looks okay before I do.

I'm also using this board.txt, I made a separate entry for my Uno's, do they all look okay? I basically used the fuses from the standard Arduino boards.txt with the change of 0x05 to 0x06 for the BOD? I noticed in the makefile that you can specify the fuses, do I need to compile a bootloader for each device with the exact fuses, or will one bootloader for 16 / 8 / 1Mhz suffice?

Thank you very much in advance, the bootloader is amazing work.

menu.cpu=Processor

##############################################################

pro.name=MySensors Bootloader for Pro Mini

pro.upload.tool=arduino:avrdude
pro.upload.protocol=arduino
pro.upload.maximum_size=30720
pro.upload.maximum_data_size=2048

pro.bootloader.tool=arduino:avrdude
pro.bootloader.unlock_bits=0x3F
pro.bootloader.lock_bits=0x0F

pro.build.mcu=atmega328p
pro.build.board=AVR_PRO
pro.build.core=arduino:arduino
pro.build.variant=arduino:standard

## Arduino with MYSBootloader Beta 2
## -------------------------------------------------

## pro.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8) 1.3 Beta 2
## pro.menu.cpu.16MHzatmega328.upload.speed=115200
## pro.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
## pro.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
## pro.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
## pro.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B2_16Mhz.hex
## pro.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

## pro.menu.cpu.8MHzatmega328=ATmega328 8MHz (RC, BOD1V8) 1.3 Beta 2
## pro.menu.cpu.8MHzatmega328.upload.speed=38400
## pro.menu.cpu.8MHzatmega328.bootloader.low_fuses=0xE2
## pro.menu.cpu.8MHzatmega328.bootloader.high_fuses=0xDA
## pro.menu.cpu.8MHzatmega328.bootloader.extended_fuses=0x06
## pro.menu.cpu.8MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B2_8Mhz.hex
## pro.menu.cpu.8MHzatmega328.build.f_cpu=8000000L

## pro.menu.cpu.1MHzatmega328=ATmega328 1MHz (RC/8, BOD1V8) 1.3 Beta 2
## pro.menu.cpu.1MHzatmega328.upload.speed=9600
## pro.menu.cpu.1MHzatmega328.bootloader.low_fuses=0x62
## pro.menu.cpu.1MHzatmega328.bootloader.high_fuses=0xDA
## pro.menu.cpu.1MHzatmega328.bootloader.extended_fuses=0x06
## pro.menu.cpu.1MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B2_1Mhz.hex
## pro.menu.cpu.1MHzatmega328.build.f_cpu=1000000L

## Arduino with MYSBootloader Beta 3
## -------------------------------------------------

pro.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8) 1.3 Beta 3
pro.menu.cpu.16MHzatmega328.upload.speed=115200
pro.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
pro.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
pro.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
pro.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B3_16Mhz.hex
pro.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

pro.menu.cpu.8MHzatmega328=ATmega328 8MHz (RC, BOD1V8) 1.3 Beta 3
pro.menu.cpu.8MHzatmega328.upload.speed=38400
pro.menu.cpu.8MHzatmega328.bootloader.low_fuses=0xFF
pro.menu.cpu.8MHzatmega328.bootloader.high_fuses=0xDA
pro.menu.cpu.8MHzatmega328.bootloader.extended_fuses=0x06
pro.menu.cpu.8MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B3_8Mhz.hex
pro.menu.cpu.8MHzatmega328.build.f_cpu=8000000L

pro.menu.cpu.1MHzatmega328=ATmega328 1MHz (RC/8, BOD1V8) 1.3 Beta 3
pro.menu.cpu.1MHzatmega328.upload.speed=9600
pro.menu.cpu.1MHzatmega328.bootloader.low_fuses=0x62
pro.menu.cpu.1MHzatmega328.bootloader.high_fuses=0xDA
pro.menu.cpu.1MHzatmega328.bootloader.extended_fuses=0x06
pro.menu.cpu.1MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B3_1Mhz.hex
pro.menu.cpu.1MHzatmega328.build.f_cpu=1000000L

##############################################################
##############################################################
##############################################################
##############################################################
##############################################################

menu.cpu=Processor

##############################################################

uno.name=MySensors Bootloader for Uno

uno.upload.tool=arduino:avrdude
uno.upload.protocol=arduino
uno.upload.maximum_size=32256
uno.upload.maximum_data_size=2048

uno.bootloader.tool=arduino:avrdude
uno.bootloader.unlock_bits=0x3F
uno.bootloader.lock_bits=0x0F

uno.build.mcu=atmega328p
uno.build.board=AVR_UNO
uno.build.core=arduino:arduino
uno.build.variant=arduino:standard

## Arduino with MYSBootloader Beta 2
## -------------------------------------------------

## uno.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8) 1.3 Beta 2
## uno.menu.cpu.16MHzatmega328.upload.speed=115200
## uno.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
## uno.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
## uno.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
## uno.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B2_16Mhz.hex
## uno.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

## Arduino with MYSBootloader Beta 3
## -------------------------------------------------

uno.menu.cpu.16MHzatmega328=ATmega328 16MHz (XTAL, BOD1V8) 1.3 Beta 3
uno.menu.cpu.16MHzatmega328.upload.speed=115200
uno.menu.cpu.16MHzatmega328.bootloader.low_fuses=0xFF
uno.menu.cpu.16MHzatmega328.bootloader.high_fuses=0xDA
uno.menu.cpu.16MHzatmega328.bootloader.extended_fuses=0x06
uno.menu.cpu.16MHzatmega328.bootloader.file=MYSBootloader/MYSBootloader_B3_16Mhz.hex
uno.menu.cpu.16MHzatmega328.build.f_cpu=16000000L

[tekka]

@Mark-Swift What changes did you make to the bootloader - the code size seems increased

[Mark Swift]

@tekka None that I'm aware of? :(

I just changed the fuses in the makefile to match the ones in my boards.txt, not sure if that's required, can you take a look at my questions above, I really want to be sure I'm doing all of this right before deploying.

To recap with regards the bootloader.

1. Installed Windows 7
2. Installed mingw (core and c++ compiler)
3. Installed Arduino IDE and MySensors library (Installed at the same location as you, at c drive root)
4. Downloaded bootloader from github
5. Edited the fuses and clock speed at the top of the makefile to match my boards.txt
6. Ran makefile from cmd

[tekka]

@Mark-Swift ok, most probably a false alarm. I assume you tested it after compilation?

[Mark Swift]

@tekka It seems to work? I guess if there was an issue it wouldn't work at all?

Please can you conform my fuses look okay in the boards.txt I posted above? Also, do I need to change the fuses in the makefile and make a file for each device, or just 1 x 16Mhz and 1 x 8Mhz for example?

[tekka]

@Mark-Swift I'm not at my workstation right now - you have to adjust the fuse settings according to your HW configurations and preferences. The fuse settings in the makefile are obsolete if you use the Arduino IDE / boards.txt for flashing. Please use the AVR fuse calculator to calculate to correct fuse settings:

http://www.engbedded.com/fusecalc/

[Mark Swift]

I @tekka, I thought as much, so basically I just need a bootloader with the right Mhz and then set fuses in the Arduino IDE boards.txt.

I used the fuse settings from the original boards.txt included with the Arduino IDE, but adjusted the extended one to 0x06 (Adjust BOD).

I noticed you used slightly different fuses to the Arduino IDE, you're using fuses that indicate a floating crystal or something?

[andreground]

@tekka

First of all, thanks for working so hard on the new version of the BL.

My setup:

• MYSBootloader 1.3.0-beta3 (md5 49ef3dc263110613c9c25ac21a8c3d83)
• MYSController 1.0.0.beta (updated to latest version)
• GW on Arduino Nano
• Node on Arduino Pro Mini @ 5V 16 Mhz with MockMySensors sketch running

What I did:

• Flashed latest bootloader version from github on the Pro Mini ATMEGA328P (using AVRDUDESS 2.4 & USBasp, fuses L: 0xFF, H: 0xDA, E: 0x05)
• Flashed latest mysensors lib on both node & gw (tested with both 2.0.0 & 2.1) on the Nano

What I got:

• FW upgrade through MYSController: Working
• Reboot through MYSController: Working
• Serial flashing with Arduino IDE: Working
• Request presentation through MYSController: Working
  Request heartbeat through MYSController: Working

But...

Reassign ID through MYSController: NOT WORKING (the node reboots but still preserves the old ID)
(MY_NODE_ID IS NOT DEFINED / THUS SET AS AUTO AS PER MYSENSORS DEFAULTS)
Clear EEPROM through MYSController: NOT WORKING (the node reboots but still holds the value saved in EEPROM using saveState)

Node bootlog after Clear EEPROM from MYSBootloader (you can see my debug LOADSTATE which still loads the value 123 from EEPROM):

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=4)
TSM:FPAR
TSP:MSG:SEND 4-4-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSP:MSG:READ 150-150-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
TSP:MSG:BC
TSP:MSG:READ 0-0-4 s=255,c=3,t=8,pt=1,l=1,sg=0:0
TSP:MSG:FPAR RES (ID=0, dist=0)
TSP:MSG:PAR OK (ID=0, dist=1)
TSM:FPAR:OK
TSM:ID
TSM:CHKID:OK (ID=4)
TSM:UPL
TSP:PING:SEND (dest=0)
TSP:MSG:SEND 4-4-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
TSP:MSG:READ 0-0-4 s=255,c=3,t=25,pt=1,l=1,sg=0:1
TSP:MSG:PONG RECV (hops=1)
TSP:CHKUPL:OK
TSM:UPL:OK
TSM:READY
GW Started
LOADSTATE
123

And...is it expected that the "Info" tab on my node shows bootloader version 1.2?

Is there anything I'm missing to have these features working?

Thanks in advance

[tekka]

@andreground Yes, re-assigning can be done nowadays with the MySensors framework, i.e. send a C_INTERNAL/I_ID_RESPONSE/<NEW ID> message to the (active) node.