Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

AC 230V energy meter

jocke4u last edited by

Hi,

I have mounted a 3-phase energy meter on my water heater which has a S0 signal that I use in a modified version of http://www.mysensors.org/build/pulse_power
It works just fine except for one small detail, it get stuck to the last watt value when it shuts off (0 watt) because no S0 signal and therefore no interrupt.
The fix I have applied right now is to invalidate watt variable (set to 0) if it's more than 7 sec ago since last blink.

I wonder if there are a better solution to this, do you have an idea?

/ Jocke
Reply Quote 0
1 Reply Last reply

1
Posts

982
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3304
Views

No one has replied
Serial Gateway woes
Development • • OldSurferDude

1

0
Votes

1
Posts

9
Views

No one has replied
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

27
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD
MYSController with MQTT Gateway (via Node Red)
Development • • slt1

1

1
Votes

1
Posts

10
Views

No one has replied
[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

3

0
Votes

3
Posts

15
Views

Thanks, I'll keep this in mind if I decide to debug it. I realized that I am also tired of patching the gateway through to the doctor container inside an LXC so now I am looking at creating an esp gateway. Just need to check if I can find a pcb on here. Thanks again!
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

5

0
Votes

5
Posts

19
Views

@eiten said in Saving last known good state, but not in EEPROM: utility meter in home assistant This is exactly what I am seeking! Thank you! PS I truly enjoy reverse translating! It teaches me how to better understand my first language and it gives me alternate words to use in searches. So a second thank you! "Regelmässiges Zurücksetzen" would be best translated to English in this context as "Periodic Reset". In the English version of Home Assistant it is called "Meter reset cycle" (I remember seeing "keep dry" translated as "do not take in shower with you"

AC 230V energy meter

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Serial Gateway woes
Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

43
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

AC 230V energy meter

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Serial Gateway woes Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red) Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000' Development • • kiesel

Saving last known good state, but not in EEPROM Development • • OldSurferDude

43Online

11.4kUsers

11.1kTopics

112.6kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Serial Gateway woes
Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

43
Online

11.4k
Users

11.1k
Topics

112.6k
Posts