nRF5 action!

scalz

@neverdie said in nRF5 Bluetooth action!:

@scalz To get smaller size, I expect we'll see modules with reduced pin counts for the 52840, just as we already do for the 52832. Have you heard anything about when final silicon for the 840 will be shipping?

yes sure. reduced IO pin counts.. and maybe even more reduced if they try to fit new features instead of IO (like usb etc). The above holyiot module example:

replace two IOs by USB pins.
keep same pinouts, but no USB, pity for a new interesting feature, but i can imagine not all people interested in it
need to enlarge the module for same pinout + usb pins
same module size and pinout, +usb, -> add bottom pads

I still don't get the point of a holyiot module, and chip antenna modules, when it's not for wearables though!

Complete waste of specs :) a 840 like that would be "funny", not much pins, with a chip ant..what would be the point then to buy a 840?? short ble5 range, no usb or just a few ios etc, yuk!
If you're after range, then take a look at the range comparison fanstel made. it's explicit how their different module design impact range. But if you don't need all the new bells&whistles of 840, then it may be smarter to use 832 or nrf24pa, and a good module, too bad to buy a module with degraded RF..

I asked Nordic two months ago, I don't think their eta changed. should be soon I imagine.

NeverDie

@scalz said in nRF5 Bluetooth action!:

I still don't get the point of a holyiot module, and chip antenna modules, when it's not for wearables though!

Not really disagreeing with you, but it's nonetheless interesting that if you do a search on Aliexpress for nrf52832 and sort the results by number of orders, the HolyIOT has gotten by far the biggest number of orders: https://www.aliexpress.com/premium/nrf52832.html?spm=2114.search0204.0.0.631303423oXjxi&site=glo&groupsort=1&SortType=total_tranpro_desc&g=y&SearchText=nrf52832&tc=ppc&initiative_id=SB_20180117073832&needQuery=n&filterCat=100000201,200010206,200084026

[Edit: I'm wrong. The Ebyte module got the most orders.]

NeverDie

I measured the Fanstel BTC832X at maximum Tx, and it draws more current than I had thought: around 330ma. As you would expect, though, the range and coverage is excellent, even at 2mbps, and even for diminutive receivers like the HolyIOT. :)

For that reason, I think it generally beats the RFM69's performance, which IIRC consumes around 100ma at max Tx power, but has a max transmit speed of 300kbps. i.e. Total mah to transmit a payload should be less with the Fanstel BT832X.

NeverDie

Since the Fanstel's don't come with the low frequency crystal oscillators already installed, when it is worthwhile to install them? I'm blithely running off the built-in RC oscillator, and I'm not noticing problems.

NeverDie

Even with two CR2032's in series, I can't get 330ma out of them for very long, if at all, before internal resistance becomes severe and it plummets to 110ma or less. Nonetheless, at least some of the preliminary testing suggests that the initial burst may be good enough to extend the Tx range for long enough (100ms) to reliably wake a sleeping receiver node that sits outside the range of a non-amplified transmitter.

Jokgi

@neverdie The internal RC Osc will allow you to keep your BOM costs lower. However when using the Bluetooth Softdevice the Crystal will lower the power consumption as the BT window will be narrower.

NeverDie

@jokgi said in nRF5 Bluetooth action!:

@neverdie The internal RC Osc will allow you to keep your BOM costs lower. However when using the Bluetooth Softdevice the Crystal will lower the power consumption as the BT window will be narrower.

Is the choice of RC osc or crystal of any consequence at all for Nordic's proprietary radio modes? For instance, I wasn't sure whether or not the cyrstal's greater accuracy might achieve a lower bit error rate at 2mbps.

Nca78

@neverdie I suppose the radio is using the high frequency clock, so it doesn't have any influence ?

d00616

@nca78 said in nRF5 Bluetooth action!:

@neverdie I suppose the radio is using the high frequency clock, so it doesn't have any influence ?

The LFCLK is required for BLE timing. Without the MCU required more energy to generate (synthetic) or calibrate (RC) the 32kHz signal.

NeverDie

@d00616 said in nRF5 Bluetooth action!:

@nca78 said in nRF5 Bluetooth action!:

@neverdie I suppose the radio is using the high frequency clock, so it doesn't have any influence ?

The LFCLK is required for BLE timing. Without the MCU required more energy to generate (synthetic) or calibrate (RC) the 32kHz signal.

Since Mysensors isn't using BLE, then it doesn't matter?

Toyman

Where can i get a Kicad component for Ebyte nrf52832?

mtiutiu

@toyman

You can find it in my kicad repo: symbol and footprint

I didn't used it in any design so please double check.

nagelc

Any suggestions how can I get serial debug messages out of the NRF52832 (Fanstel BT832)? I can upload the program over the SWD interface. I'm using a black magic probe with the Arduino NRF5 package on Windows 10. I know it works because the node shows up in my controller.

NeverDie

@nagelc said in nRF5 Bluetooth action!:

Any suggestions how can I get serial debug messages out of the NRF52832 (Fanstel BT832)?

Define one of the pins as serial TXO. Then connect it to RXI on an FTDI TTL-USB converter and read it that way. That's what I do, and it works.

nagelc

@neverdie
Do you define the pins in MyBoardNRF5? In MyBoadNRF5.cpp, I replaced the 0 in the first line with10, thinking this will map Arduino TX0 to P010. This did not seem to work. How do you map the TX0 pin?

NeverDie

@nagelc No, you want to change the values in the MyBoardNRF5.h file instead. For an example, see the source code in: https://www.openhardware.io/view/499/10-years-wireless-PIR-Sensor-on-just-one-set-of-3-AAs#tabs-source

So, in your case, you'd want:

#define PIN_SERIAL_TX       (10)

and, to avoid conflicts, make sure that pin P0.10 isn't defined anywhere in the same .h file as something else already. If it is, you may need to change that as well.

nagelc

Thanks. I'll give that a try.

Toyman

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

1200mah capacity
1.8-3.0v range
low cost (ca. $3)
41,0 x 24,5 x 5,2 dimensions and, importantly
up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

Nca78

@toyman said in nRF5 Bluetooth action!:

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

1200mah capacity

1.8-3.0v range

low cost (ca. $3)

41,0 x 24,5 x 5,2 dimensions and, importantly

up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

Mhmhmh, a disposable battery that you have to solder I can't see it as a good idea for a node...

Toyman

@nca78 said in nRF5 Bluetooth action!:

@toyman said in nRF5 Bluetooth action!:

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

1200mah capacity

1.8-3.0v range

low cost (ca. $3)

41,0 x 24,5 x 5,2 dimensions and, importantly

up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

Mhmhmh, a disposable battery that you have to solder I can't see it as a good idea for a node...

well, 1200mah will last AT LEAST for a year (two in real life). I have no issues resoldering 2 joints once a year, given it gives AAA capacity in a much smaller package

nRF5 action!

25

11.7k

11.2k

113.1k