nRF5 action!

[mtiutiu]

@toyman

You can find it in my kicad repo: symbol and footprint

I didn't used it in any design so please double check.

[nagelc]

Any suggestions how can I get serial debug messages out of the NRF52832 (Fanstel BT832)? I can upload the program over the SWD interface. I'm using a black magic probe with the Arduino NRF5 package on Windows 10. I know it works because the node shows up in my controller.

[NeverDie]

@nagelc said in nRF5 Bluetooth action!:

Any suggestions how can I get serial debug messages out of the NRF52832 (Fanstel BT832)?

Define one of the pins as serial TXO. Then connect it to RXI on an FTDI TTL-USB converter and read it that way. That's what I do, and it works.

[nagelc]

@neverdie
Do you define the pins in MyBoardNRF5? In MyBoadNRF5.cpp, I replaced the 0 in the first line with10, thinking this will map Arduino TX0 to P010. This did not seem to work. How do you map the TX0 pin?

[NeverDie]

@nagelc No, you want to change the values in the MyBoardNRF5.h file instead. For an example, see the source code in: https://www.openhardware.io/view/499/10-years-wireless-PIR-Sensor-on-just-one-set-of-3-AAs#tabs-source

So, in your case, you'd want:

#define PIN_SERIAL_TX       (10)

and, to avoid conflicts, make sure that pin P0.10 isn't defined anywhere in the same .h file as something else already. If it is, you may need to change that as well.

[nagelc]

Thanks. I'll give that a try.

[Toyman]

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

• 1200mah capacity
• 1.8-3.0v range
• low cost (ca. $3)
• 41,0 x 24,5 x 5,2 dimensions and, importantly
• up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

[Nca78]

@toyman said in nRF5 Bluetooth action!:

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

• 1200mah capacity
• 1.8-3.0v range
• low cost (ca. $3)
• 41,0 x 24,5 x 5,2 dimensions and, importantly
• up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

Mhmhmh, a disposable battery that you have to solder I can't see it as a good idea for a node...

[Toyman]

@nca78 said in nRF5 Bluetooth action!:

@toyman said in nRF5 Bluetooth action!:

Yesterday, I 've got a mailing from my components' supplier featuring new type of cells, Li-MnO2. The cell has all the features needed for nRF5:

• 1200mah capacity
• 1.8-3.0v range
• low cost (ca. $3)
• 41,0 x 24,5 x 5,2 dimensions and, importantly
• up to 120mah peak discharge current.

The link to manufacturer:
http://www.fanso-battery.com/Ultra-thin-Li-MnO2-battery-CP502440-3V1200mAh-pd1905.html

Mhmhmh, a disposable battery that you have to solder I can't see it as a good idea for a node...

well, 1200mah will last AT LEAST for a year (two in real life). I have no issues resoldering 2 joints once a year, given it gives AAA capacity in a much smaller package

[NeverDie]

Speaking of batteries, I found only one proper holder for holding two CR2032's in series:

It turns out you pretty much need the plastic carrier to guarantee that the edge of the button cell doesn't short out against the side of the metal holding bracket.

[d00616]

@neverdie said in nRF5 Bluetooth action!:

Speaking of batteries, I found only one proper holder for holding two CR2032's in series:

There are CR2477 (560mAh) or CR2450 (950mAh) 3V cells. Maybe its's better to handle.

[NeverDie]

@toyman said in nRF5 Bluetooth action!:

41,0 x 24,5 x 5,2 dimensions and, importantly

Footprint seems kinda large, at least for nodes intended to be small. It trades off length in order to get thin. In contrast, a CR123 is shorter (34.5mm), but thicker (17mm), but can deliver 1.5a continuous (which makes it very tempting for powering a PA):
https://www.batteryjunction.com/energizer-cr123a.html
On the other hand, when you add the CR123 holder, the length may be comparable.

If you decide to try out the fanso, please do let us know how you like it.

[NeverDie]

@d00616 said in nRF5 Bluetooth action!:

There are CR2477 (560mAh) or CR2450 (950mAh) 3V cells. Maybe its's better to handle.

Good point. I think maybe the only actual justified use of two CR2032's in series is to power the AM612, which requires a voltage of at least 2.7v.

[Omemanti]

Did someone get an NRF52 working with an ESP8266(ESP32) and successfully connected it to a controller?

Since my controller is something stuffed away in a closet, Id like to have a gateway that's positioned more centralized. An ESP+NRF52832 would be a lovely cost-efficient solution.

[NeverDie]

@omemanti said in nRF5 Bluetooth action!:

Did someone get an NRF52 working with an ESP8266(ESP32) and successfully connected it to a controller?

Yes: https://www.openhardware.io/view/491/PA-LNA-nRF52832-ESP-LINK-Shield-for-Wemos-D1-Mini-ESP8266

Works great! :)

[Omemanti]

@neverdie ah thnx. I'll try it out with my nodemcu+ebyte

[nagelc]

@neverdie
It worked! I used pin 26 as in your example and now can get the debug messages. Also thanks for the many other NRF5 routines you had in the example.

[Omemanti]

How can I connect to DEC5 as an I/O when using MyBoardNRF5?

The Ebyte Module Datasheet says: 14 DEC5 Input/Output MCU GPIO to it should be possible?

[NeverDie]

@omemanti Suggest you check the Nordic datasheet on that rather than rely on the Ebyte documentation. IIRC, the DECT pins are not GPIO, but it's worth your double checking the nRF52 datasheet if it's important to you.

[Omemanti]

@neverdie, Indeed, I checked and it was false. well goes to show that late-night prototyping has some disadvantages, my bad, :)

Deleted Following up question..
DK =>Ebyte module
GND(detect) => GND
SWDIO => SWDIO
SWDCLK => SWCLK
VTG => 3,3V
3,3V => 3,3V
GND =>GND