Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

present() not sending or being received?

Stuart Middleton last edited by

I've been running a small test setup for some time with just 1 node and 1 gateway. For some reason, in the past week or so, I've noticed that the "present" doesn't either send or get to the gateway. I'm using MYSController to look at the messages but if I delete the node and let it re-register itself, it only gets its name and sometimes 1 of the 4 sensors presented. It once got 2 of them. I don't think it's a transmission problem as the node can happily send hundreds of quick fire messages without dropout.

Has anyone encountered this? Can anyone think of a reason this would happen before I start debugging the code?

Thanks,
Reply Quote 0
1 Reply Last reply

1
Posts

447
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3304
Views

No one has replied
Serial Gateway woes
Development • • OldSurferDude

1

0
Votes

1
Posts

9
Views

No one has replied
MYSController with MQTT Gateway (via Node Red)
Development • • slt1

1

1
Votes

1
Posts

10
Views

No one has replied
MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

198

13
Votes

198
Posts

84990
Views

@tekka Is there any changelog to it also or it was just made officially available again? although last online status was 22 AUG 2020, so anyone else can confirm anything about it? I'd just be cautious without confirmation.
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

5

0
Votes

5
Posts

19
Views

@eiten said in Saving last known good state, but not in EEPROM: utility meter in home assistant This is exactly what I am seeking! Thank you! PS I truly enjoy reverse translating! It teaches me how to better understand my first language and it gives me alternate words to use in searches. So a second thank you! "Regelmässiges Zurücksetzen" would be best translated to English in this context as "Periodic Reset". In the English version of Home Assistant it is called "Meter reset cycle" (I remember seeing "keep dry" translated as "do not take in shower with you"
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

27
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD

present() not sending or being received?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Serial Gateway woes
Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

51
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

present() not sending or being received?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Serial Gateway woes Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red) Development • • slt1

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta Development • ota myscontroller mysbootloader • • tekka

Saving last known good state, but not in EEPROM Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

51Online

11.4kUsers

11.1kTopics

112.6kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Serial Gateway woes
Development • • OldSurferDude

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

MYSBootloader 1.3 pre-release & MYSController 1.0.0beta
Development • ota myscontroller mysbootloader • • tekka

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

51
Online

11.4k
Users

11.1k
Topics

112.6k
Posts