Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

ce pin for nrf24l01 necessary ?

rozpruwacz last edited by

Hi all,

I just run out of io pins available in my project that uses arduino pro mini and I need to connect one more device (ds18b20 sensor). I wonder if the CE pin of the nrf24l01 module is necesary when using it in a repeater node mode ? I believe that the nrf stays always on in that mode so is it possible to use that pin for other purpose ?
Reply Quote 0
1 Reply Last reply

1
Posts

982
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3307
Views

No one has replied
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

28
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD
MYSController with MQTT Gateway (via Node Red)
Development • • slt1

1

1
Votes

1
Posts

12
Views

No one has replied
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

25
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

32
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!

ce pin for nrf24l01 necessary ?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

Gateway without a radio
Development • • OldSurferDude

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

73
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

ce pin for nrf24l01 necessary ?

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red) Development • • slt1

Gateway without a radio Development • • OldSurferDude

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

73Online

11.5kUsers

11.1kTopics

112.7kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

Gateway without a radio
Development • • OldSurferDude

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

73
Online

11.5k
Users

11.1k
Topics

112.7k
Posts