What did you build today (Pictures) ?

[kalina]

I have finished an enclosure for the my MDMSPanel "Nextion" today.

[alowhum]

Wow, very cool! Can you share a bit more about the project? Is it MySensors based? Is there code available? What does the hardware inside look like? What processor is it base on?

Ah, scrolling up answered some of my questions :-)

[kalina]

@alowhum Yes of course. I am going to publish this project this week.

[dbemowsk]

@kalina Kudos on the case. Is that a case you designed, or is it a prefab case that you bought somewhere? I am assuming that from the markings inside the case that it is a prefab.I do like the design though and love it's underlying project. Is that just a thermostat, or is it a multi option controller?

[kalina]

@dbemowsk Yes, it is a factory case, and before the changing it looked like this :

At the moment this is termostat, but I will not limit myself to this)) The purpose of the panel will be determined by the software project loaded into it. I will describe this in more detail when I publish the project.

[bjacobse]

@kalina
Yes it's very impressing what you have achieved

[dbemowsk]

@kalina I like that case design so much that I may design one like it in OpenSCAD and post it on thingiverse.

[kalina]

@bjacobse said in What did you build today (Pictures) ?:

Yes it's very impressing what you have achieved

Thanks, the project is published already.

https://www.openhardware.io/view/676/MDMSPanel-Nextion

[FotoFieber]

Building a (xenon) flash to notify alarms. Flashes every 5 seconds if activated.

[sundberg84]

[sundberg84]

Today I made a iscp pogo pin adapter... Great for uploading bootloaders.

[berkseo]

Almost finished one of my projects. The test sketch showed that HW works as it should. Now i need to make good software.

https://youtu.be/dfhDseDaGiA

[Omemanti]

@sundberg84 that board looks nice and crisp 👍

[berkseo]

Birth of water leakage sensor:) on mysensors..
https://youtu.be/xsoeffaGAG0

[Omemanti]

After months of slow painstaking work (day job is somewhat busy, o and the kids ;) ) I finally completed my Domoticz server(case) with Dashticz as frontend.

The Endgame; when my new house is finished every room is monitored for motion, RH and Temperature using my MySensors PCB's. (Jung AS500 Node)

Everything is monitored using a raspberry with a MySensors serial gateway (NRF52) and an RFLink controller for my KAKU switches.

To make everything nice and shiny I use Dasticz to interface the data in a proper way using a tablet that somehow will be mounted on a wall or something.

So far the introduction;
To put everything away nice and tidy I used a box to install everything using 2 pieces of din-rail.
It has a 230V inlet that is converted to 5V using an off the shelf (safety sake) MeanWell RS-15-5 converter. This powers everything using a couple of din-Rail terminals.

• Terminal => USB-micro => Raspberry
• Terminal => just a couple of wires => old nrf52 prototype => FTDI => Raspberry
• Raspberry => RF-link (ard. Mega +433mhz)

Since the Raspberry has Wifi no other cable then power is needed to operate

Second part: the 2 screenshots of dasthicsz.

The best part, it took some work, but the WAF incread big time, because everything looks clean :)

[dbemowsk]

@omemanti Nice DIN rail enclosure.

[Omemanti]

@dbemowsk

If someone would be interested:
Enclosure
Ard. Mega enclosure
Raspberry enclosure

Had to do some modifications for the mega, but the cost of this enclosure was more than worth it.

Hmz.. normaly don't buy stuff at conrad but apparently they have good prices on cases... 😏

[monte]

@omemanti well...enclosure at a price of 3 raspberry pi zero. Good price indeed :)

[sundberg84]

[Honk]

Nothing fancy. Got my new ts100 today and I pre-soldered some V10 easyPCBs with 3.3v Arduino pro minis.
The iron is pretty good. It is Louis Rossmann approved. Now I need a good 24V power source to drive this thing.