3. How can I include MyMessage object in my own class?

How can I include MyMessage object in my own class?

  • gryzli133

    Dear all, I have been trying to change my Arduino Mega project controlling 16 relays for Light on/off. The board is working standalone as gateway for Domoticz. The reason is, I want to have bullet proof Smart Home with only one point of failture - in this case arduino Mega. Untill now I was separately creating every button/relay, so a lot of code. I though it would be nice, to create a class switch, and then create a array of 16 objects of class switch. This will make the code looking much better. The problem is, I need to create object MyMessage in my own class switch, how can I do it? The code is compiling until I declare MyMessage msg(child_id, V_LIGHT) inside the class switch. I will leave code for single switch and my code trying convert it to class object.

    Original working code:

    

// Enable debug prints to serial monitor
#define MY_DEBUG 


// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level. 
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
// #define MY_WITH_LEDS_BLINKING_INVERSE

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <SPI.h>
#include <MySensors.h>  
#include <Bounce2.h>

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE


#define RELAY_1  4  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

#define BUTTON_PIN A1


void before() { 
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
    // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}
Bounce debouncer = Bounce();

void setup() { 
  // Setup locally attached sensors
  delay(10000);
   // Setup the button.
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  // After setting up the button, setup debouncer.
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  //presentation();
}
void presentation()  
{   
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay", "1.0");

  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_LIGHT);
  }
}

MyMessage msg(1, V_LIGHT);

void loop() { 
  // Send locally attached sensor data here 
  if (debouncer.update()) {
    // Get the update value.
    int value = debouncer.read();
    // Send in the new value.
    if(value == LOW){
         saveState(1, !loadState(1));
         digitalWrite(RELAY_1, loadState(1)?RELAY_ON:RELAY_OFF);
         send(msg.set(loadState(1)));
    }
  }
}


void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

    Here the new object oriented version:

    

// Enable debug prints to serial monitor
#define MY_DEBUG 


// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level. 
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 38400
#endif

// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
// #define MY_WITH_LEDS_BLINKING_INVERSE

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>  
#include <Bounce2.h>



class Switch
{ 
  public:
  uint8_t child_id;
  int buttonPin;
  int relayPin;
  bool relayON;
  bool relayOFF;
  Bounce debouncer = Bounce();

  
  
  Switch(int childId, int button, int relay, int debaunce, bool invertedRelay)
  {
    child_id = childId;
    buttonPin = button;
    relayPin = relay;
    relayON = !invertedRelay;
    relayOFF = invertedRelay;
    pinMode(buttonPin, INPUT_PULLUP);
    debouncer.attach(buttonPin);
    debouncer.interval(debaunce);
    pinMode(relayPin, OUTPUT);
    digitalWrite(relayPin, loadState(child_id)?relayON:relayOFF); 
  }
  
  MyMessage msg(child_id, V_LIGHT);
  
  void Update()
  {
    if (debouncer.update()) 
    {
      // Get the update value.
      int value = debouncer.read();
      // Send in the new value.
      if(value == LOW)
      {
         saveState(child_id, !loadState(child_id));
         digitalWrite(relayPin, loadState(child_id)?relayON:relayOFF);
         send(msg.set(loadState(child_id)));
      }
    }    
  }

  void Present()
  {
    present(child_id, S_LIGHT);
  }

  void Update(const MyMessage &message)
  {
    // We only expect one type of message from controller. But we better check anyway.
    if (message.type==V_LIGHT && message.sensor==child_id) 
    {
       // Change relay state
       digitalWrite(relayPin, message.getBool()?relayON:relayOFF);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       // Write some debug info
       Serial.print("Incoming change for sensor:");
       Serial.print(message.sensor);
       Serial.print(", New status: ");
       Serial.println(message.getBool());
     } 
  }
};



void setup() 
{ 
  // Setup locally attached sensors
  delay(10000);
}
void presentation()  
{   
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay", "1.0");
}

void loop() 
{ 

}


void receive(const MyMessage &message) {

}

    PS: if you move the line with: MyMessage msg(child_id, V_LIGHT); at the before class declaration and change the child_id to f.e. 1, everything is compiling....

    0
  • gryzli133

    nobody can help? ;-(

    0
  • pjr

    @gryzli133 said in How can I include MyMessage object in my own class?:

    MyMessage msg(child_id, V_LIGHT);

    IMO you are trying to initialize MyMessage object before your class has any value for child_id. Can be resolved using object reference.
    https://www.embedded.com/electronics-blogs/programming-pointers/4024641/An-Introduction-to-References

    So you wont initialize msg variable until when constructing instance of your class..
    Declare MyMessage &msg; in your class
    and set value for it in your class constructor: msg = MyMessage(child_id, V_LIGHT);

    ps. I'm natively writing C# and C++ isnt my strongest language so this might not be right 😉

    edit: did read bit more.. you need to init msg before entering inside constructor logic:

    class Switch
{
public:
  Switch(........ int &child_id ......... ) : msg(child_id, V_LIGHT) { 
     ..................
  }
  MyMessage &msg;
};

    I hope this works 🙂

    1
  • rozpruwacz

    @pjr version is almost correct, it would be correct without references, so skip '&' symbol and it should work

    2
  • gryzli133

    You are great guys! It compile already, later I will also check the functionality 😉

    1
Log in to reply
 

Suggested Topics

  • hek


    Announcements •  

    1
  • OldSurferDude


    Development •  

    2
  • OldSurferDude


    Development •  

    1
  • pikim


    Development •  

    10
  • kiesel


    Development •  

    3
  • Marcin


    Development •  

    3

2
Online

11.4k
Users

11.1k
Topics

112.7k
Posts



Copyright 2019 Sensnology   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service