Windows GUI/Controller for MySensors

[mfalkvidd]

@swiss which capacitor(s) do you use? The nrf radio is extremely sensitive to power fluctuations.

[swiss]

@mfalkvidd
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
12 TSM:INIT:TSP OK
14 TSM:FPAR
16 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2025 !TSM:FPAR:NO REPLY
2027 TSM:FPAR
2029 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4038 !TSM:FPAR:NO REPLY
4040 TSM:FPAR
4042 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6051 !TSM:FPAR:NO REPLY
6053 TSM:FPAR
6055 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8065 !TSM:FPAR:FAIL
8067 TSM:FAIL:CNT=1
8069 TSM:FAIL:PDT
18073 TSM:FAIL:RE-INIT
18075 TSM:INIT
18081 TSM:INIT:TSP OK
18085 TSM:FPAR
18087 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20097 !TSM:FPAR:NO REPLY
20099 TSM:FPAR
20101 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
22110 !TSM:FPAR:NO REPLY
22112 TSM:FPAR
22114 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24123 !TSM:FPAR:NO REPLY
24125 TSM:FPAR
24127 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
26136 !TSM:FPAR:FAIL
26138 TSM:FAIL:CNT=2
26140 TSM:FAIL:PDT
36143 TSM:FAIL:RE-INIT
36145 TSM:INIT
36151 TSM:INIT:TSP OK
36155 TSM:FPAR
36157 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
38166 !TSM:FPAR:NO REPLY
38168 TSM:FPAR
38170 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
40179 !TSM:FPAR:NO REPLY
40181 TSM:FPAR
40183 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
42194 !TSM:FPAR:NO REPLY
42196 TSM:FPAR
42199 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
44208 !TSM:FPAR:FAIL
44210 TSM:FAIL:CNT=3
44212 TSM:FAIL:PDT
54216 TSM:FAIL:RE-INIT
54218 TSM:INIT
54224 TSM:INIT:TSP OK
54228 TSM:FPAR
54231 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
56240 !TSM:FPAR:NO REPLY
56242 TSM:FPAR
56244 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
58253 !TSM:FPAR:NO REPLY
58255 TSM:FPAR
58257 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
60266 !TSM:FPAR:NO REPLY
60268 TSM:FPAR
60270 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
62279 !TSM:FPAR:FAIL
62281 TSM:FAIL:CNT=4
62283 TSM:FAIL:PDT
72286 TSM:FAIL:RE-INIT
72288 TSM:INIT
72294 TSM:INIT:TSP OK
72298 TSM:FPAR
72300 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
74309 !TSM:FPAR:NO REPLY
74311 TSM:FPAR
74313 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
76322 !TSM:FPAR:NO REPLY
76324 TSM:FPAR
76326 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
78336 !TSM:FPAR:NO REPLY
78338 TSM:FPAR
78340 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
80349 !TSM:FPAR:FAIL
80351 TSM:FAIL:CNT=5
80353 TSM:FAIL:PDT

at the moment i have no capacitors in place since i thought the communication was ok...

[mfalkvidd]

@swiss ok. No use to troubleshoot further without capacitors.

[swiss]

@mfalkvidd
ok sorry will ad them right now - sorry for using your time

[swiss]

thank you so much for kicking me into the right direction...
now the log of the node looks different:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
4 TSM:INIT
4 TSF:WUR:MS=0
12 TSM:INIT:TSP OK
14 TSM:FPAR
16 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2025 !TSM:FPAR:NO REPLY
2027 TSM:FPAR
2029 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2037 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
2043 TSF:MSG:FPAR OK,ID=0,D=1
3500 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
4038 TSM:FPAR:OK
4038 TSM:ID
4040 TSM:ID:REQ
4044 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
6051 TSM:ID
6051 TSM:ID:REQ
6055 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
8065 TSM:ID
8065 TSM:ID:REQ
8069 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
10076 TSM:ID
10076 TSM:ID:REQ
10080 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
12089 !TSM:ID:FAIL
12091 TSM:FAIL:CNT=1
12093 TSM:FAIL:PDT
22097 TSM:FAIL:RE-INIT
22099 TSM:INIT
22106 TSM:INIT:TSP OK
22110 TSM:FPAR
22112 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24004 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
24010 TSF:MSG:FPAR OK,ID=0,D=1
24121 TSM:FPAR:OK
24123 TSM:ID
24123 TSM:ID:REQ
24127 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
26136 TSM:ID
26136 TSM:ID:REQ
26140 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
28149 TSM:ID
28149 TSM:ID:REQ
28153 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
30164 TSM:ID
30164 TSM:ID:REQ
30169 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
32178 !TSM:ID:FAIL
32180 TSM:FAIL:CNT=2
32182 TSM:FAIL:PDT
42186 TSM:FAIL:RE-INIT
42188 TSM:INIT
42194 TSM:INIT:TSP OK
42199 TSM:FPAR
42201 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
44097 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
44103 TSF:MSG:FPAR OK,ID=0,D=1
44210 TSM:FPAR:OK
44212 TSM:ID
44212 TSM:ID:REQ
44216 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
46225 TSM:ID
46225 TSM:ID:REQ
46229 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
48238 TSM:ID
48238 TSM:ID:REQ
48242 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
50251 TSM:ID
50251 TSM:ID:REQ
50255 TSF:MSG:SEND,255-255-0-0,s=255,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
52267 !TSM:ID:FAIL
52269 TSM:FAIL:CNT=3
52271 TSM:FAIL:PDT

If understand it correct it got feedback from parent and is now requesting its id ? correct?
Is it correct that the ID should come from the Controller, in my case the Myscontroller ?
unfortunately i cant connect the controller to the Gateway, is there anything else i can check beside the IP and the port ?

thank you so much for your assistance would really love to make it happen...
matt

[mfalkvidd]

@swiss yes, that's correct.

What does the gateway log say when you connect the controller?

[swiss]

Here is the log of the gateway, it starts when i press "discover" on the software (after i connected)
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.8.155
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSF:MSG:BC
0;255;3;0;9;TSF:MSG:FPAR REQ,ID=255
0;255;3;0;9;TSF:CKU:OK,FCTRL
0;255;3;0;9;TSF:MSG:GWL OK
0;255;3;0;9;TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
0;255;3;0;9;TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.8.155
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.8.155
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.8.155
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.8.155
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1

but no node is found... and if i press discover again i got error 10054 in the software and the connection is terminated by the remote...

[mfalkvidd]

@swiss I would guess you are using Arduino AVR board version 1.6.19 (check in the board manager). If that is the case, the solution seems to be to downgrade. See https://forum.mysensors.org/post/72423

[swiss]

MAN,YOU ARE MY HERO!!!
IT WORKS - THANK YOU FOR ALL YOUR SUPPORT
TAKE CARE
MATT

[mfalkvidd]

@swiss great! Thanks for reporting back.

[Dab0G]

How can I increase the number of blocks greater than 2048?

[2017-12-05 16:04:36.925 Info] REPO FW "STM32_RS485_Node_Relay" loaded. t=100, v=7, blocks=2048, crc=0xCC88
[2017-12-05 16:04:36.926 Info] REPO FW repository loaded. Items=2
[2017-12-05 16:04:52.544 Info] INFO FW "STM32_RS485_Node_Relay" assigned to node 100
[2017-12-05 16:04:52.545 Info] INFO Send FW info to node 100: type=64, version=7, blocks=0x0800, CRC=0xCC88

For STM32F407ZGT6, it may take up to 65k blocks. And in the controller, I understand it is a hard limit on 2048?

[robosensor]

Is it OK?

https://www.virustotal.com/#/file/6082b86e6a56783e692afaa7c6d79e5af0d6ca58476ef7e180a39594ce441cd7/detection

No such warnings/detections for .282 version.

[Homer]

Hi all

I have an issue which I've documented in the Troubleshooting section. When I've searched for a resolution, this program has been mentioned. What I'm trying to do is get my controller to see the part of the gateway sketch that references a sensor that I added. Can this program help? What does this program actually do?

[scalz]

@Homer
Try it ;)
It's a handy controller software for debugging MySensors.

[kalj]

This is quite a nice piece of software! You have suggested you are going to release the sources at some point. Maybe that time is now? It would be great to see if it can be ported to Linux!

[mickecarlsson]

Bug in MYScontroller.
When I edit the file firmware_config.csv and set a version number with a decimal the output in the debug is wrong.
This is my file:

Type,Name,Version,File,Comments
10,Blink,1,Blink.ino.hex,blinking example
20,Tvattstugan-2,3,Tvattstugan-2.ino.hex,Testar Flash
30,Tvattstugan,2,Tvattstugan.ino.hex,Tvattstugan
40,Sovrummet,2.1,Sovrummet.ino.hex,Sovrummet

Note that I have 2.1 as the version in 40, Sovrummet.
But when I load the repo in MYSController v is 65535:

2021-02-13 17:06:37	REPO	FW "Blink" loaded. t=10, v=1, blocks=80, crc=0x46D4
2021-02-13 17:06:37	REPO	FW "Tvattstugan-2" loaded. t=20, v=3, blocks=1488, crc=0x6D13
2021-02-13 17:06:37	REPO	FW "Tvattstugan" loaded. t=30, v=2, blocks=960, crc=0xBB4F
2021-02-13 17:06:37	REPO	FW "Sovrummet" loaded. t=40, v=65535, blocks=936, crc=0x6AB3
2021-02-13 17:06:37	REPO	FW repository loaded. Items=4

And in the GUI the version is also 65535.

Actually there are two bugs.
If I add (sloppy I know) more empty lines at the end in the firmware_config.csv file I get this in the debug:

2021-02-13 17:13:35	REPO	FW "Blink" loaded. t=10, v=1, blocks=80, crc=0x46D4
2021-02-13 17:13:35	REPO	FW "Tvattstugan-2" loaded. t=20, v=3, blocks=1488, crc=0x6D13
2021-02-13 17:13:35	REPO	FW "Tvattstugan" loaded. t=30, v=2, blocks=960, crc=0xBB4F
2021-02-13 17:13:35	REPO	FW "Sovrummet" loaded. t=40, v=65535, blocks=936, crc=0x6AB3
2021-02-13 17:13:35	ERROR	2107-15-31 is not a valid date specification

Other than that, great piece of software. Thanks.

[ru64]

Download seems unavailable. Could you please update the link?

[mickecarlsson]

Here is a version that I downloaded a long time ago.
EDIT: It seems that I can't upload files. Bummer. PM me if you want the file.

[Mac65]

@tekka can you provide sources of this project?
Thanks
Mac65

[emre299]

link broken, please share new link