CNC PCB milling

executivul

Manually written gcode to determine milling bit width

DON'T run it on your machine untill you understand exactly what each line of code does!

G21
G90
G94
F1400.00
G00 Z0.5000
M03
G4 P1
G01 Z-0.1000
G4 P0.5

(test 0.1mm)
G01 X0.0000Y5.0000
G01 X0.1000Y5.0000
G01 X0.1000Y0.0000
G01 X0.2000Y0.0000

G01 X0.2000Y5.0000
G01 X0.3000Y5.0000
G01 X0.3000Y0.0000
G01 X0.4000Y0.0000

G01 X0.4000Y5.0000
G01 X0.5000Y5.0000
G01 X0.5000Y0.0000
G01 X0.6000Y0.0000

G01 X1.6000Y0.0000

(test 0.2mm)
G01 X1.6000Y5.0000
G01 X1.8000Y5.0000
G01 X1.8000Y0.0000
G01 X2.0000Y0.0000

G01 X2.0000Y5.0000
G01 X2.2000Y5.0000
G01 X2.2000Y0.0000
G01 X2.4000Y0.0000

G01 X2.4000Y5.0000
G01 X2.6000Y5.0000
G01 X2.6000Y0.0000
G01 X2.8000Y0.0000

G01 X3.8000Y0.0000

(test 0.3mm)
G01 X3.8000Y5.0000
G01 X4.1000Y5.0000
G01 X4.1000Y0.0000
G01 X4.4000Y0.0000

G01 X4.4000Y5.0000
G01 X4.7000Y5.0000
G01 X4.7000Y0.0000
G01 X5.0000Y0.0000

G01 X5.0000Y5.0000
G01 X5.3000Y5.0000
G01 X5.3000Y0.0000
G01 X5.6000Y0.0000

G01 X6.6000Y0.0000

(test 0.4mm)
G01 X6.6000Y5.0000
G01 X7.0000Y5.0000
G01 X7.0000Y0.0000
G01 X7.4000Y0.0000

G01 X7.4000Y5.0000
G01 X7.8000Y5.0000
G01 X7.8000Y0.0000
G01 X8.2000Y0.0000

G01 X8.2000Y5.0000
G01 X8.6000Y5.0000
G01 X8.6000Y0.0000
G01 X9.0000Y0.0000

G01 X10.0000Y0.0000

(test 0.5mm)
G01 X10.0000Y5.0000
G01 X10.5000Y5.0000
G01 X10.5000Y0.0000
G01 X11.0000Y0.0000

G01 X11.0000Y5.0000
G01 X11.5000Y5.0000
G01 X11.5000Y0.0000
G01 X12.0000Y0.0000

G01 X12.0000Y5.0000
G01 X12.5000Y5.0000
G01 X12.5000Y0.0000
G01 X13.0000Y0.0000

G01 X14.0000Y0.0000

(test 0.6mm)
G01 X14.0000Y5.0000
G01 X14.6000Y5.0000
G01 X14.6000Y0.0000
G01 X15.2000Y0.0000

G01 X15.2000Y5.0000
G01 X15.8000Y5.0000
G01 X15.8000Y0.0000
G01 X16.4000Y0.0000

G01 X16.4000Y5.0000
G01 X17.0000Y5.0000
G01 X17.0000Y0.0000
G01 X17.6000Y0.0000

G01 X18.6000Y0.0000

(test 0.7mm)
G01 X18.6000Y5.0000
G01 X19.3000Y5.0000
G01 X19.3000Y0.0000
G01 X20.0000Y0.0000

G01 X20.0000Y5.0000
G01 X20.7000Y5.0000
G01 X20.7000Y0.0000
G01 X21.4000Y0.0000

G01 X21.4000Y5.0000
G01 X22.1000Y5.0000
G01 X22.1000Y0.0000

G00 Z1.5000
G00 X0Y0
M05

When you see copper "silvers" between the passes you know your bit is 0.1mm narrower than the corresponding width :sunglasses:

NeverDie

@executivul Good stuff! I imagine I'll get there eventually, but on Day 1 I'd rather start with some reasonable magic constants that at least put me in the ballpark.

NeverDie

@sundberg84 said in CNC PCB milling:

@neverdie I'm saving up some money for a CNC as well and I would love if you have time to document your process. Might be to much to ask but I guess many newbie errors could be avoided. I know there are some on YouTube but I have not found any which address the questions we have had above in this thread.

Yes, that's what I'm attempting to do on this thread. :)

andrew

JFYI: CNC 2418 assembly by me :)

https://www.youtube.com/watch?v=T2_18-ObvP0

I'll try to make a blog to describe the whole pcb cnc milling, tools etc, as well as other diy projects. I'll let you know if there is any notable progress...

NeverDie

@andrew Nice. How long did that take in earth minutes?

andrew

@NeverDie about 6 hours, in two nights

executivul

Best way to get rid of the dust seems to be not making dust to start with.
Enjoy!
https://youtu.be/PpXG1X9yoxs

NeverDie

@executivul Which car shampoo?

How well does it work? Would it work better if you flooded it a bit more so that it was sitting, say, a couple mm under shampoo solution?

NeverDie

I suppose your etching bit might last longer too, since maybe the liquid would help cool it.

executivul

Unfortunately I can not disclose this secret recipe, all I can tell you is that s some cationic surfactant mixed with some dihydrogen peroxide :sunglasses:

To be honest I don't know the brand, I've first tried liquid soap undiluted but was to thick and was gathering around the bit like a small tornado and splashing everywhere, decided to add some water and went looking for a spray bottle, found one with some handwriting "car shampoo", it is thicker than plain water, but not as thick as liquid soap, so it might be diluted, I still have some for a few more boards then I'll go by trial and error with dish/hand/car wash and water.
So much better not to have windows open at 0C(32F) and the vacuum howling. Only the 2.0mm endmill still creates dust, normal engraving and drilling do not.
Don't forget to mill on acrylic/plastic as mdf will swell if wet.

NeverDie

Looks like my CNC2418 is on track to be delivered this Monday. It has already cleared customs.

So, since it will be arriving well ahead of all the various bits and such, I'm guessing that just a few etching bits will be enough to get me started and confirm whether my machine can route 6 mil isolation.

The kit itself includes 0.1mm bits (Diameter: 3.175mm tip: 0.1mm length: 30mm).

NeverDie

It arrived!

Yveaux

@neverdie Yay! Where can we find the live stream of the build process? ;-)

andrew

@neverdie so, I expect your first boards tomorrow :)

NeverDie

@andrew said in CNC PCB milling:

@neverdie so, I expect your first boards tomorrow :)

But wait, I'm still waiting for the magic numbers from you. :) Otherwise, I'll be all dressed with nowhere to go.

andrew

@neverdie once the assembly is done, you should adjust the stepper drivers' current limiting as well.
it is pololu a4988, you can find the corresponding details here:
https://www.pololu.com/product/1182

then, it is always good idea to have the basic settings exported from the board, just in case... you can do it by "$$" command sent from the g code sender gui or directly from the serial terminal.

currently I use the following settings, the machine might be able to create nice results with higher feed rates, but I did not have enough time to test it and I sticked to the current working config.

isolation routing with 2001 bits:

z cut: -0.05mm
feed rate: 200

you can calculate the V carving bit's tool width for the given milling depth with the following formula:
tan(bit angle/2) * milling depth * 2 + bit's end width
for excel formula the bit angle should be provided in radians, so it should look like this
tan(radians(bit angle/2)) * milling depth * 2 + bit's end width

edge cut or hole milling with the 0.8mm endmill:

feed rate: 170
z cut: -1.7mm
multi depth, depth/pass: 0.2mm

drilling:

feed rate: 130
z cut: -1.8

the spindle should be 1000 everywhere.

most probably your board will not have a bootloader, so it will not be possible to update the firmware via usb serial connection (with avrdude), but it is worth to try it. for me it did not work, so I traced back the MCU pins to the pin rows and used ISP to upgrade the firmware to grbl v1.1f (the board will come with 0.9j if I remember correctly). do not forget to export the gerber settings before you upgrade the firmware, as it will loose those, and you have to re-assign the given values again, after the update.

the ISP pinout (from the pin row's top left corner):
Reset -> pin 2
SCK -> pin 3
MISO -> pin 12
MOSI -> pin 13

5v -> pin1
gnd-> bottom row(!) e.g. pin 1

NeverDie

The assembly instructions came as a file on a mini CD. Attached for anyone who is interested.
[0_1513463653125_2418-Assembly instructions - English.doc](Uploading 100%)
Hmmm.. I guess the forum only lets me upload photos. Sorry.

NeverDie

I thought that the ER11 would come pre-installed ("shrink fit" onto the spindle), but it arrived as a separate piece and apparently I'm supposed to attach it by hand. That would seem to be a discrepancy with Jack's store advertises for this device, but, oh well.

Also, I was a bit surprised to see that most, and maybe all, of the plastic parts were 3D printed.

NeverDie

@andrew said in CNC PCB milling:

do not forget to export the gerber settings before you upgrade the firmware, as it will loose those, and you have to re-assign the given values again, after the update.

Where are the gerber settings, and how do I export them? Are they in EEPROM, so I just do a complete copy of that? Or does the $$ handle it?

NeverDie

I finished putting together the first frame. It was a bit frustrating, because the T-slot nuts they use can come out of the groove, and so to prevent that I had to keep constant tension on it while I tightened it down. I do think most of the T-slot nuts should have been the kind that don't slip out that way.

CNC PCB milling

23

11.7k

11.2k

113.1k