@hek said in Door, Window and Push-button Sensor:

pinMode(i + FIRST_PIN, INPUT_PULLUP);

Big Thanks!
I have changed all array parts in setup in the same manner like above and it works

@rodaman
Hi,
Here is a sketch for multi buttons (no relays, no repeated parts of code for each buttons) just enter number of buttons and first digital pin where buttons are attached.
Thanks to @hek for help...

/**
   The MySensors Arduino library handles the wireless radio link and protocol
   between your home built sensors/actuators and HA controller of choice.
   The sensors forms a self healing radio network with optional repeaters. Each
   repeater and gateway builds a routing tables in EEPROM which keeps track of the
   network topology allowing messages to be routed to nodes.

   Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
   Copyright (C) 2013-2015 Sensnology AB
   Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

   Documentation: http://www.mysensors.org
   Support Forum: http://forum.mysensors.org

   This program is free software; you can redistribute it and/or
   modify it under the terms of the GNU General Public License
   version 2 as published by the Free Software Foundation.

 *******************************

   DESCRIPTION

   Simple binary switch example updated  for multi switches
   Connect buttons or door/window reed switches between
   digitial I/O choosen pin  (FIRST_PIN below) and GND.
   http://www.mysensors.org/build/binary
*/


// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_GATEWAY_SERIAL

//#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define FIRST_PIN  2  // Arduino Digital I/O pin for button/reed switch
#define noButtons 6


Bounce debouncer[noButtons] = Bounce();

int oldValue[noButtons];
int value;
MyMessage msg[noButtons];

void setup() {

  for (int i = 0; i < noButtons; i++) {

    oldValue[i] = -1;
    
    msg[i].sensor = i;                                   // initialize messages
    msg[i].type = V_TRIPPED; //
    pinMode(i + FIRST_PIN, INPUT_PULLUP);
    digitalWrite(i + FIRST_PIN, HIGH);
  
    debouncer[i] = Bounce();                        // initialize debouncer
    debouncer[i].attach(i + FIRST_PIN);
    debouncer[i].interval(3);
  }
}

void presentation() {
  sendSketchInfo("Doors", "1.0");
  for (int i = 0; i < noButtons; i++)
    present(i, S_DOOR);                               // present sensor to gateway
}


//  Check if digital input has changed and send in new value
void loop()
{
  for (int i = 0; i < noButtons; i++) {
    debouncer[i].update();

    value = debouncer[i].read();
    if (value != oldValue[i]) {
    // Send in the new value
      send(msg[i].set(value == HIGH ? 1 : 0));
      oldValue[i] = value;
    }
 }
}

You are right. Mysensors based on NRF is dead. I started my adventure with home automation based on mysensors but gradually I replaced all my sensor with Wemos. Now everything work fine. Sorry mysensors...

After 3 years of using RADIO_RF24 i replaced my all sensors with espeasy. It was just big battle with lost transmissions, disconnections, every day problems. Now for many days silence...Everything works.I still use mysensors in diferrent setup but NRF Radio is asking for trouble.

@rodaman
Hi,
Here is a sketch for multi buttons (no relays, no repeated parts of code for each buttons) just enter number of buttons and first digital pin where buttons are attached.
Thanks to @hek for help...

/**
   The MySensors Arduino library handles the wireless radio link and protocol
   between your home built sensors/actuators and HA controller of choice.
   The sensors forms a self healing radio network with optional repeaters. Each
   repeater and gateway builds a routing tables in EEPROM which keeps track of the
   network topology allowing messages to be routed to nodes.

   Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
   Copyright (C) 2013-2015 Sensnology AB
   Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

   Documentation: http://www.mysensors.org
   Support Forum: http://forum.mysensors.org

   This program is free software; you can redistribute it and/or
   modify it under the terms of the GNU General Public License
   version 2 as published by the Free Software Foundation.

 *******************************

   DESCRIPTION

   Simple binary switch example updated  for multi switches
   Connect buttons or door/window reed switches between
   digitial I/O choosen pin  (FIRST_PIN below) and GND.
   http://www.mysensors.org/build/binary
*/


// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_GATEWAY_SERIAL

//#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define FIRST_PIN  2  // Arduino Digital I/O pin for button/reed switch
#define noButtons 6


Bounce debouncer[noButtons] = Bounce();

int oldValue[noButtons];
int value;
MyMessage msg[noButtons];

void setup() {

  for (int i = 0; i < noButtons; i++) {

    oldValue[i] = -1;
    
    msg[i].sensor = i;                                   // initialize messages
    msg[i].type = V_TRIPPED; //
    pinMode(i + FIRST_PIN, INPUT_PULLUP);
    digitalWrite(i + FIRST_PIN, HIGH);
  
    debouncer[i] = Bounce();                        // initialize debouncer
    debouncer[i].attach(i + FIRST_PIN);
    debouncer[i].interval(3);
  }
}

void presentation() {
  sendSketchInfo("Doors", "1.0");
  for (int i = 0; i < noButtons; i++)
    present(i, S_DOOR);                               // present sensor to gateway
}


//  Check if digital input has changed and send in new value
void loop()
{
  for (int i = 0; i < noButtons; i++) {
    debouncer[i].update();

    value = debouncer[i].read();
    if (value != oldValue[i]) {
    // Send in the new value
      send(msg[i].set(value == HIGH ? 1 : 0));
      oldValue[i] = value;
    }
 }
}

@hek said in Door, Window and Push-button Sensor:

pinMode(i + FIRST_PIN, INPUT_PULLUP);

Big Thanks!
I have changed all array parts in setup in the same manner like above and it works

@hek
I have changed

pinMode(buttonPin[i + FIRST_PIN], INPUT_PULLUP);

to

pinMode(buttonPin[i + FIRST_PIN], INPUT);

thanks, but sadlly still does not work...

@hek
That part was in original sketch for establish internal pullup as I understand. I used array to do it for each pins.

@mfalkvidd
thank you, i hope will be good soul who fix my sketch itself to work...

Hi,
I rewrite sketch for doors/window/buttons to work with multiple buttons (no rellays) .It shows up in Domoticz but it did not change status buttons if pressed.
Can someone look for the skech what I am doing wrong

/**
  The MySensors Arduino library handles the wireless radio link and protocol
  between your home built sensors/actuators and HA controller of choice.
  The sensors forms a self healing radio network with optional repeaters. Each
  repeater and gateway builds a routing tables in EEPROM which keeps track of the
  network topology allowing messages to be routed to nodes.

  Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
  Copyright (C) 2013-2015 Sensnology AB
  Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

  Documentation: http://www.mysensors.org
  Support Forum: http://forum.mysensors.org

  This program is free software; you can redistribute it and/or
  modify it under the terms of the GNU General Public License
  version 2 as published by the Free Software Foundation.

*******************************

  DESCRIPTION

  Simple binary switch example updated  for 2 switches
  Connect button or door/window reed switch between
  digitial I/O pin 3 (BUTTON_PIN below) and GND.
  http://www.mysensors.org/build/binary
*/


// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_GATEWAY_SERIAL

//#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define FIRST_PIN  8  // Arduino Digital I/O pin for button/reed switch
#define noButtons 4
const int buttonPin[noButtons];

Bounce debouncer[noButtons] = Bounce();

int oldValue[noButtons];

MyMessage msg[noButtons];

void setup() {

 for (int i = 0; i < noButtons; i++) {

   msg[i].sensor = i;                                   // initialize messages
   msg[i].type = V_TRIPPED; //

   pinMode(buttonPin[i + FIRST_PIN], INPUT_PULLUP);
   digitalWrite(buttonPin[i + FIRST_PIN], HIGH);
   debouncer[i] = Bounce();                        // initialize debouncer
   debouncer[i].attach(buttonPin[i + FIRST_PIN]);
   debouncer[i].interval(30);
 }
}

void presentation() {
 sendSketchInfo("Doors", "1.0");
 for (int i = 0; i < noButtons; i++)
   present(i, S_DOOR);                               // present sensor to gateway


}


//  Check if digital input has changed and send in new value
void loop()
{
 for (int i = 0; i < noButtons; i++) {
   debouncer[i].update();

   int value = debouncer[i].read();
   if (value != oldValue[i]) {

     // Send in the new value
     send(msg[i].set(value == HIGH ? 1 : 0));
     oldValue[i] = value;
   }

 }
}

@palande-vaibhav
Sorry for the dumb question. How do you achieved different #numbering in Values? I have all my Ds18b20 sensors with #1 number.