@tekka thanks for the answer. I'm still a newbie.
Now I can not make a contribution to the development due to my incompetence.
I can help as a tester
Posts made by wanvo
-
RE: MYSBootloader 1.3.0-beta.3
-
RE: MYSBootloader 1.3.0-beta.3
Hi @tekka!
Do you plan to add support for the RFM69 module in MYSBootloader? -
RE: [SOLVED]ESP8266_MQTT gate RFM69 not communicate with node
Thanks to all.
The problem is solved.
I forgot to add pin definitions to the sketch.#define MY_RF69_IRQ_PIN D1 #define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN #define MY_RF69_SPI_CS D8 // NSS. Use MY_RFM69_CS_PIN for the development branch.```
-
RE: [SOLVED]ESP8266_MQTT gate RFM69 not communicate with node
My Node out
__ __ ____ | \/ |_ _/ ___| ___ _ __ ___ ___ _ __ ___ | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __| | | | | |_| |___| | __/ | | \__ \ _ | | \__ \ |_| |_|\__, |____/ \___|_| |_|___/\___/|_| |___/ |___/ 2.2.0-rc.2 18 MCO:BGN:INIT NODE,CP=RPNNA---,VER=2.2.0-rc.2 28 TSM:INIT 28 TSF:WUR:MS=0 32 TSM:INIT:TSP OK 34 TSM:INIT:STATID=1 36 TSF:SID:OK,ID=1 38 TSM:FPAR 1038 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 3045 !TSM:FPAR:NO REPLY 3047 TSM:FPAR 4050 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 6060 !TSM:FPAR:NO REPLY 6062 TSM:FPAR 7065 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 9072 !TSM:FPAR:NO REPLY 9074 TSM:FPAR 10076 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 12083 !TSM:FPAR:FAIL 12085 TSM:FAIL:CNT=1 12087 TSM:FAIL:DIS 12089 TSF:TDI:TSL 22093 TSM:FAIL:RE-INIT 22095 TSM:INIT 22097 TSM:INIT:TSP OK 22099 TSM:INIT:STATID=1 22104 TSF:SID:OK,ID=1 22106 TSM:FPAR 23109 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 25116 !TSM:FPAR:NO REPLY 25118 TSM:FPAR 26120 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 28127 !TSM:FPAR:NO REPLY
I checked this node with the gate OrangePiZero MQTT
and the RF69 module on this gate was the same as on the ESP8266. Everything worked well. -
[SOLVED]ESP8266_MQTT gate RFM69 not communicate with node
Hi guys.
I loaded the following code into my gate
// Enable debug prints to serial monitor #define MY_DEBUG // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h //#define MY_BAUD_RATE 9600 // Enables and select radio type (if attached) #define MY_RADIO_RFM69 #define MY_IS_RFM69HW //#define MY_RFM69_FREQUENCY RF69_868MHZ #define MY_RFM69_NEW_DRIVER #define MY_DEBUG_VERBOSE_RFM69 //#define MY_RADIO_RFM95 #define MY_GATEWAY_MQTT_CLIENT #define MY_GATEWAY_ESP8266 // Set this node's subscribe and publish topic prefix #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in" // Set MQTT client id #define MY_MQTT_CLIENT_ID "mysensors-1" // Enable these if your MQTT broker requires usenrame/password //#define MY_MQTT_USER "username" //#define MY_MQTT_PASSWORD "password" // Set WIFI SSID and password //#define MY_ESP8266_SSID "OrPiZero" //#define MY_ESP8266_PASSWORD "orangepi" #define MY_ESP8266_SSID "wanvo" #define MY_ESP8266_PASSWORD "merkulovanastya" // Set the hostname for the WiFi Client. This is the hostname // it will pass to the DHCP server if not static. // #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway" // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP) //#define MY_IP_ADDRESS 192,168,178,87 // If using static ip you can define Gateway and Subnet address as well //#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 //#define MY_IP_SUBNET_ADDRESS 255,255,255,0 // MQTT broker ip address. //#define MY_CONTROLLER_IP_ADDRESS 10, 0, 0, 1 #define MY_CONTROLLER_IP_ADDRESS 192, 168, 0, 107 // The MQTT broker port to to open #define MY_PORT 1883 // Enable inclusion mode //#define MY_INCLUSION_MODE_FEATURE // Enable Inclusion mode button on gateway //#define MY_INCLUSION_BUTTON_FEATURE // Set inclusion mode duration (in seconds) //#define MY_INCLUSION_MODE_DURATION 60 // Digital pin used for inclusion mode button //#define MY_INCLUSION_MODE_BUTTON_PIN 3 // Set blinking period //#define MY_DEFAULT_LED_BLINK_PERIOD 300 // Flash leds on rx/tx/err //#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin //#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin //#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED #include <ESP8266WiFi.h> #include <MySensors.h> void setup() { Serial.setDebugOutput(true); // Setup locally attached sensors } void presentation() { // Present locally attached sensors here } void loop() { // Send locally attech sensors data here }
And the gate does not try to search for nodes. This is what I get from the serial debugger
MCO:BGN:INIT GW,CP=RPNGE---,VER=2.2.0-rc.2 238 TSF:LRT:OK 240 TSM:INIT 241 TSF:WUR:MS=0 242 RFM69:INIT 243 RFM69:INIT:PIN,CS=15,IQP=2,IQN=2 247 RFM69:PTX:LEVEL=5 dBm 250 TSM:INIT:TSP OK 251 TSM:INIT:GW MODE 253 TSM:READY:ID=0,PAR=0,DIS=0 256 MCO:REG:NOT NEEDED scandone f 0, scandone state: 0 -> 2 (b0) state: 2 -> 3 (0) state: 3 -> 5 (10) add 0 aid 5 cnt connected with wanvo, channel 7 dhcp client start... 761 .ip:192.168.0.106,mask:255.255.255.0,gw:192.168.0.1 1261 .1261 IP: 192.168.0.106 1263 MCO:BGN:STP 1265 MCO:BGN:INIT OK,TSP=1 1267 IP: 192.168.0.106 1269 Attempting MQTT connection... 2275 MQTT connected 2277 Sending message on topic: mygateway1-out/0/255/0/0/18 pm open,type:2 0
Noda is on, but does not see the gate.
Tell me, what is the reason for this behavior of the gate?