💬 Sensebender Gateway

[pepson]

hi
when i try compile sketch only with change radio to rfm69hw i have this:
Arduino:1.8.9 (Windows 10), Płytka:"Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"

SensebenderGatewaySerial:95:26: error: 'LED_BLUE' was not declared in this scope

static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};

                      ^

SensebenderGatewaySerial:95:36: error: 'LED_RED' was not declared in this scope

static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};

                                ^

SensebenderGatewaySerial:95:45: error: 'LED_GREEN' was not declared in this scope

static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};

                                         ^

SensebenderGatewaySerial:95:56: error: 'LED_YELLOW' was not declared in this scope

static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};

                                                    ^

SensebenderGatewaySerial:95:68: error: 'LED_ORANGE' was not declared in this scope

static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};

                                                                ^

C:\Users\Piotrek\Desktop\SensebenderGatewaySerial-sketch\SensebenderGatewaySerial\SensebenderGatewaySerial.ino: In function 'void preHwInit()':

SensebenderGatewaySerial:116:10: error: 'MY_SWC1' was not declared in this scope

pinMode(MY_SWC1, INPUT_PULLUP);

      ^

SensebenderGatewaySerial:117:10: error: 'MY_SWC2' was not declared in this scope

pinMode(MY_SWC2, INPUT_PULLUP);

      ^

SensebenderGatewaySerial:130:17: error: 'LED_BLUE' was not declared in this scope

digitalWrite(LED_BLUE, led_state);

             ^

SensebenderGatewaySerial:145:16: error: 'LED_GREEN' was not declared in this scope

digitalWrite(LED_GREEN, HIGH);

            ^

SensebenderGatewaySerial:149:16: error: 'LED_YELLOW' was not declared in this scope

digitalWrite(LED_YELLOW, HIGH);

            ^

SensebenderGatewaySerial:154:16: error: 'LED_ORANGE' was not declared in this scope

digitalWrite(LED_ORANGE, HIGH);

            ^

SensebenderGatewaySerial:167:17: error: 'LED_RED' was not declared in this scope

digitalWrite(LED_RED, HIGH);

             ^

C:\Users\Piotrek\Desktop\SensebenderGatewaySerial-sketch\SensebenderGatewaySerial\SensebenderGatewaySerial.ino: In function 'bool testSDCard()':

SensebenderGatewaySerial:219:33: error: 'MY_SDCARD_CS' was not declared in this scope

if (!card.init(SPI_HALF_SPEED, MY_SDCARD_CS)) {

                             ^

C:\Users\Piotrek\Desktop\SensebenderGatewaySerial-sketch\SensebenderGatewaySerial\SensebenderGatewaySerial.ino: In function 'bool testEEProm()':

SensebenderGatewaySerial:249:2: error: 'SerialUSB' was not declared in this scope

SerialUSB.print(" -> EEPROM ");

^

C:\Users\Piotrek\Desktop\SensebenderGatewaySerial-sketch\SensebenderGatewaySerial\SensebenderGatewaySerial.ino: In function 'bool testAnalog()':

SensebenderGatewaySerial:267:30: error: 'MY_BAT_DETECT' was not declared in this scope

int bat_detect = analogRead(MY_BAT_DETECT);

                          ^

exit status 1
'LED_BLUE' was not declared in this scope

What is error ? please help me

[pepson]

I also can not install board in Arduino IDE 1.8.9

[pepson]

please help
https://forum.mysensors.org/topic/10548/solved-sensbender-gateway-gives-a-lot-of-hu/2

[magpern]

@pepson said in 💬 Sensebender Gateway:

hi
when i try compile sketch only with change radio to rfm69hw i have this:
Arduino:1.8.9 (Windows 10), Płytka:"Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"

SensebenderGatewaySerial:95:26: error: 'LED_BLUE' was not declared in this scope

You cannot use the SensebenderGatewaySerial sketch on an Atmega2560. The SensbenderGatewaySerial sketch is for the SAMD board called Sensebender Gateway.

If you have the real Sensebender Gateway you should use this one

[pepson]

@magpern
But get this board to Arduino IDE?

[magpern]

@pepson said in 💬 Sensebender Gateway:

@magpern
But get this board to Arduino IDE?

Boards / Boards manager...
search for sensebender

You might have to

File / Preferences / Additional Board manager URLs
add
https://raw.githubusercontent.com/mysensors/ArduinoBoards/master/package_mysensors.org_index.json

[pepson]

Hi
I compiled and write to gateway this programmm. Then i connected it to my RPI with Hassio (Home Assistant). In logs on home assistant still show me info: Gateway /dev/serial/by-id/usb-MySensors.org_Sensebender_GW_6A153443514D355934202020FF10182D-if00 not ready after 15.0 secs so continuing with setup

but after run Home Assistant gateway works ok. I send info mto developer Home Assistant ans she not see any bugs....
How i can resolved this problem ?

[pepson]

And please help me how i can compile it as gateway Ethernet with module W5100.

Only add to sketch:
// Enable gateway ethernet module type
#define MY_GATEWAY_W5100

// Enable to UDP
//#define MY_USE_UDP

//#define MY_IP_ADDRESS 192,168,3,160 // wpisz adres ip bramki
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 //wpisz numer portu bramki

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDC, 0xAE, 0xB2, 0x3F, 0xFF, 0xDC

???

[pepson]

When try compilation with this W5100 i get error:

Opcje projektu zmienione, przeładuj całość
In file included from C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/MySensors.h:208:0,

             from C:\Users\Piotrek\Desktop\SensebenderGatewayETHERNET\SensebenderGatewayETHERNET.ino:111:

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:74:1: error: 'EthernetServer' does not name a type

EthernetServer _ethernetServer(_ethernetGatewayPort);

^~~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:89:8: error: 'EthernetClient' does not name a type

static EthernetClient client = EthernetClient();

    ^~~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp: In function 'bool gatewayTransportInit()':

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:149:7: error: 'Ethernet' was not declared in this scope

if (!Ethernet.begin(_ethernetGatewayMAC)) {

   ^~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:149:7: note: suggested alternative: '_ethernetMsg'

if (!Ethernet.begin(_ethernetGatewayMAC)) {

   ^~~~~~~~

   _ethernetMsg

In file included from C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/MySensors.h:49:0,

             from C:\Users\Piotrek\Desktop\SensebenderGatewayETHERNET\SensebenderGatewayETHERNET.ino:111:

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:156:16: error: 'Ethernet' was not declared in this scope

            Ethernet.localIP()[0],

            ^

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/MyConfig.h:1815:48: note: in definition of macro 'DEBUG_OUTPUT'

#define DEBUG_OUTPUT(x,...) hwDebugPrint(x, ##VA_ARGS) //!< debug

                                            ^~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:155:2: note: in expansion of macro 'GATEWAY_DEBUG'

GATEWAY_DEBUG(PSTR("GWT:TIN:IP=%" PRIu8 ".%" PRIu8 ".%" PRIu8 ".%" PRIu8 "\n"),

^~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:156:16: note: suggested alternative: '_ethernetMsg'

            Ethernet.localIP()[0],

            ^

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/MyConfig.h:1815:48: note: in definition of macro 'DEBUG_OUTPUT'

#define DEBUG_OUTPUT(x,...) hwDebugPrint(x, ##VA_ARGS) //!< debug

                                            ^~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:155:2: note: in expansion of macro 'GATEWAY_DEBUG'

GATEWAY_DEBUG(PSTR("GWT:TIN:IP=%" PRIu8 ".%" PRIu8 ".%" PRIu8 ".%" PRIu8 "\n"),

^~~~~~~~~~~~~

In file included from C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/MySensors.h:208:0,

             from C:\Users\Piotrek\Desktop\SensebenderGatewayETHERNET\SensebenderGatewayETHERNET.ino:111:

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:189:2: error: '_ethernetServer' was not declared in this scope

_ethernetServer.begin();

^~~~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:189:2: note: suggested alternative: '_ethernetMsg'

_ethernetServer.begin();

^~~~~~~~~~~~~~~

_ethernetMsg

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp: In function 'bool gatewayTransportSend(MyMessage&)':

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:246:11: error: '_ethernetServer' was not declared in this scope

nbytes = _ethernetServer.write(_ethernetMsg);

       ^~~~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:246:11: note: suggested alternative: '_ethernetMsg'

nbytes = _ethernetServer.write(_ethernetMsg);

       ^~~~~~~~~~~~~~~

       _ethernetMsg

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp: In function 'bool _readFromClient()':

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:289:9: error: 'client' was not declared in this scope

while (client.connected() && client.available()) {

     ^~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:289:9: note: suggested alternative: 'Print'

while (client.connected() && client.available()) {

     ^~~~~~

     Print

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp: In function 'bool gatewayTransportAvailable()':

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:409:2: error: 'EthernetClient' was not declared in this scope

EthernetClient newclient = _ethernetServer.available();

^~~~~~~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:411:6: error: 'newclient' was not declared in this scope

if (newclient) {

  ^~~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:412:7: error: 'client' was not declared in this scope

if (client != newclient) {

   ^~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:412:7: note: suggested alternative: 'Print'

if (client != newclient) {

   ^~~~~~

   Print

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:422:6: error: 'client' was not declared in this scope

if (client) {

  ^~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:422:6: note: suggested alternative: 'Print'

if (client) {

  ^~~~~~

  Print

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp: In function 'void gatewayTransportRenewIP()':

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:463:6: error: 'Ethernet' was not declared in this scope

if (Ethernet.maintain() & ~(0x06)) {

  ^~~~~~~~

C:\Users\Piotrek\Documents\Arduino\libraries\MySensors/core/MyGatewayTransportEthernet.cpp:463:6: note: suggested alternative: '_ethernetMsg'

if (Ethernet.maintain() & ~(0x06)) {

  ^~~~~~~~

  _ethernetMsg

exit status 1
Błąd kompilacji dla płytki Sensebender Gateway.

What is a problem ?

[pepson]

please help me....

[pepson]

Hi
Can anybody help me how compile sketch to this gateway to work as Ethernet Gateway...
When i try compile i get the error:
https://pastebin.com/BSQGsCgi

and my sketch looks like:
https://pastebin.com/R3vG076i

[tekka]

@pepson Did you add

#include <Ethernet.h>

?

[pepson]

@tekka
No.... thanks i fixed it....:)

[Andreas Kräuchi]

I just got my Sensebender Gateway and loaded the Sensebender Gateway Serial sketch. When I use the MYSController I get those wired infos...
Currently there is no other Snesor runing just the Sensebender Gateway with an RF24. Why does it see a new child and what are all thos "hu;hu;hu" errors?

[Andreas Kräuchi]

Ok solved it by adding:

#undef PRId8
#undef PRIi8
#undef PRIo8
#undef PRIu8
#undef PRIx8
#undef PRIX8
#undef PRIdLEAST8
#undef PRIiLEAST8
#undef PRIoLEAST8
#undef PRIuLEAST8
#undef PRIxLEAST8
#undef PRIXLEAST8
#undef PRIdFAST8
#undef PRIiFAST8
#undef PRIoFAST8
#undef PRIuFAST8
#undef PRIxFAST8
#undef PRIXFAST8
#define PRId8    "d"
#define PRIi8   "i"
#define PRIo8   "o"
#define PRIu8   "u"
#define PRIx8   "x"
#define PRIX8   "X"
#define PRIdLEAST8  "d"
#define PRIiLEAST8  "i"
#define PRIoLEAST8  "o"
#define PRIuLEAST8  "u"
#define PRIxLEAST8  "x"
#define PRIXLEAST8  "X"
#define PRIdFAST8 "d"
#define PRIiFAST8 "i"
#define PRIoFAST8 "o"
#define PRIuFAST8 "u"
#define PRIxFAST8 "x"
#define PRIXFAST8 "X"

[andy5211d]

Hello,

I have a similar issue with Sensebender Ethernet MQTT Gateway and MYSController. Can only connect to the gateway by serial from MYSController. The set-up is working correctly as best I can tell, and has several different MySensors in use. Has been working for a number of years. Only just discovered the MYSController software.

So the Controller only shows data in the MYSController Debug tab. Nothing in any of the others. NOTE in the screen grab below the Controller at 192.168.1.96 is not connected, there is no difference when it is other than the Gateway error (!GWT:RMQ:FAIL) is not shown. Anyone with any ides for me to pursue? Thanks.

[bjornhallberg]

As previously noted, Sensebender Gateway sketch from 2.3.2 with MySensors SAMD Boards 1.0.6 does not compile with Arduino SAMD Boards 1.8.9. Rolling back to Arduino SAMD Boards 1.8.8 or earlier version works.

[Yoshu]

Does anyone have an idea about the sensebender gateway board not being recognised in windows 11? A new driver maybe or any other clues ?

[tbowmo]

Unfortunately I do not have any hardware compatible with win11, so can't test myself.. But if I remember right it should turn up as a generic cdc device..

Is there any info in the windows device manager?

[Yoshu]

@tbowmo

Nothing new appears in device manager or the usual ding.