RFM69 sleep mode

[hek]

If you use the MySensors sleep function it calls
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/utility/RFM69.cpp#L152

I hope the RF69 library sleep function works...

What is the expected consumption?

[Francois]

@hek as per this Web site I should get about 16uA http://forum.anarduino.com/posts/list/39.page

[hek]

Cant help you much right now as I don't have my RF69 setup up and running.

Maybe Felix over at lowpowerlab can give you some hints (we use his code for the driver).

[Francois]

@hek to get down to 3uA I have to use the following line.

LowPower.powerDown(SLEEP_8S, ADC_OFF, BOD_OFF);

How do I do this in the current library. If I use the LowPower library I get an error when compile

[hek]

Tried gw.sleep(8000); ?

[Francois]

@hek with sleep(8000) I still get 3.75mA.

[hek]

Strange that you get different values depending on radio. That points to problem with radio sleep and not the Arduino itself.

So if create a RF69 sketch that just sleeps in loop. What happens if you disconnect radio (after init)? Do you you get ~3.75uA?

[Francois]

@hek sorry how will I disconnect the radio?

[hek]

Ahh.. good question if (you're running Moteino with them soldered on).

[Francois]

@hek yes the radio is solder on

[hek]

I can't find myself doing anything different from the LowPower library in in MyAtMega328.cpp - sleep(). Need someone else's eyes on it.

[Francois]

@hek I see that you have powerDown in the MyHwATMega328.cpp how do I use that function?

void powerDown(period_t period) {

	ADCSRA &= ~(1 << ADEN);

	if (period != SLEEP_FOREVER)
	{
		wdt_enable(period);
		WDTCSR |= (1 << WDIE);
	}
	#if defined __AVR_ATmega328P__
		do {
			set_sleep_mode(SLEEP_MODE_PWR_DOWN);
			cli();
			sleep_enable();
			sleep_bod_disable();
			sei();
			sleep_cpu();
			sleep_disable();
			sei();
		} while (0);
	#else
		do {
			set_sleep_mode(SLEEP_MODE_PWR_DOWN);
			cli();
			sleep_enable();
			sei();
			sleep_cpu();
			sleep_disable();
			sei();
		} while (0);
	#endif

	ADCSRA |= (1 << ADEN);
}

[hek]

You use it by calling gw.sleep() which initiates powerDown.

https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/MySensor.cpp#L820

[Francois]

@hek Hi I got a new shipment of Arduino mini pro and after I did the low power hack on this Arduino I now are getting 30uA current usage. Thank again for all you support and for this great MySensor community that you started :). Now I can go full steam ahead in building more sensor for my house.

[NeverDie]

@Francois said:

@hek Hi I got a new shipment of Arduino mini pro and after I did the low power hack on this Arduino I now are getting 30uA current usage. Thank again for all you support and for this great MySensor community that you started :). Now I can go full steam ahead in building more sensor for my house.

So, just to be clear, is this an accurate summary: the full package (Arduino mni pro plus radio) sleeps at 30uA if using the RFW69 but sleeps at 3uA if using the NRF24L01+?

Also, does it make any difference whether it's RFM69W, RFM69CW, or RFM69HW? Do they all draw the same amount of current while sleeping?

[peres]

@NeverDie
Hi, I know this is an old thread, but it is stil a valid subject to me.
I have had success with arduino pro mini v2 and RFM69W in sleep, but not the high power version RFM69HW.
Arduino+RFM69W sleeps at 5.2micro Amp.
Arduino+RFM69HW sleeps at 420micro Amp.
I have written about it in arduino forum.
I would be glad if someone has a solution for this.

[manutremo]

Hi @peres,

My RFM69HW current during sleep is less than 1 uA aprox, which is consistent with what is shown in the datasheet. Interestingly, this is the result when powering the device with a battery; when powering the device from the PC USB serial, it's around 6 uA - still close enough as it's measured with a "normal" multimeter.

I'Which version of mysensors are you using? I've moved to 2.2.0-beta (due to me needing other functionalities not availabel in 2.1.1, namely ATC which btw works fabulously) and found that support for nrf69 is - although not yet 100% completed - significantly improved. Maybe worth a try to see if that fixes your sleep consumption?

Remember adding

#define MY_RFM69_NEW_DRIVER

to enable the new driver.

Let us know how it goes :)

[napo7]

Hi,

I have the same question, but a little bit different ;)

I use a RFM69 with the Mysensors 2.2.0 beta.
I don't sleep my node with the provided function, since I don't want to sleep for some time, but until a Pin Change Interrupt is triggered (via pin A0 or A1). So, I can't use the sleep() function.
I do put my node to sleep with avr core functions (setting registers, calling power_all_disable() and sleep_cpu()...) but I suppose the radio is never put on sleep !

Is there a function I can call to sleep the radio, and if yes, is there another function I should call before sending, to awake the radio ?

Thanks !

[scalz]

@napo7
Here the list of the core functions (radio independant):
https://ci.mysensors.org/job/Verifiers/job/MySensors/branch/development/Doxygen_HTML/group__MyTransportgrp.html#gab39d3b81f005e00117269d79c7b2ee4c

should be transportDisable/transportReInitialise

Else the radio specific functions (a layer above driver) are in the MyTransportRFM69.cpp

[napo7]

Thanks !