Sensebender Micro

[hek]

@gbfromhb

D3 is available on the side-pins. D2 is routed to the radio but can be used with some hacking.

[mvader]

@gbfromhb said:

I hope this question has not been answered already and I did not miss the answer. I was thinking about connecting a motion sensor to this and was hoping that one of the digital pins supports an interrupt. Is there an interrupt available?

I'm planning to do the same thing.
i ordered my 5v step up regulators to support the PIR sensor.
although I hope adding the motion isnt going to kill the batteries.

[gbfromhb]

@mvader
I have so far had no problems running my PIR sensors at 3.3v with the following hack.

http://techgurka.blogspot.com/2013/05/cheap-pyroelectric-infrared-pir-motion.html

You can not do this with all PIR Sensors from what I understand, but one of the ones listed in the MySensors store is what I've been using. Go down to the bottom of the article.

[gbfromhb]

@Hek
Thanks, I saw the D3, but I'm new enough to this adventure that I was not sure if I should have assumed that it also had an interrupt like all the other boards.

[tbowmo]

@gbfromhb

I tried to keep the naming, and pins on the atmega, the same as an ordinary arduino :)

[mvader]

@gbfromhb said:

@mvader
I have so far had no problems running my PIR sensors at 3.3v with the following hack.

http://techgurka.blogspot.com/2013/05/cheap-pyroelectric-infrared-pir-motion.html

You can not do this with all PIR Sensors from what I understand, but one of the ones listed in the MySensors store is what I've been using. Go down to the bottom of the article.

wow.. nice.. thanks for the info! I will give this a go asap.

[gloob]

Hello,

I have one more question. Is it possible to power the micro from the ftdi pins? I would like to use jumper wires.

[tbowmo]

@gloob

Yes it's possible to power it from the FTDI pins, if you want to..

[gloob]

Are there any recommendations for a low power temperature, humidity sensor regarding the update cycle.

Currently I plan to wake up the sensor each 10 minutes instead of each 1 minute to update the values. This should increase the duration of the battery. A complete update of all values if performed each 30 minutes as usual.

[tbowmo]

I would probably choose 5 minutes interval instead.. I have updated the sensebendermicro sketch tonight (just waiting for @hek to approve it). so it holds of on the transmissions a bit. Now the temperature needs to change more than 0.5 degrees from the previous transmitted value. OR
humidity needs to change more than 0.5, measured with a moving average. OR
30 minutes since last transmission.

[gloob]

I found that when I power the micro from 2 batteries I get the following error:

T: 23.21
H: 50
send: 104-104-0-0 s=1,c=1,t=0,pt=7,l=5,st=fail:23.2
send: 104-104-0-0 s=2,c=1,t=1,pt=2,l=2,st=fail:50

This does not happen when I power it from the FTDI programmer.
Does anybody have any ideas?
The batteries have a voltage of 3.25V

I did not have this issues with my arduino nano sensors. and i did use the same radio modules.

When I check the modules they seem to be real nrf24l01+ modules:

STATUS		 = 0x0e RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=7 TX_FULL=0
RX_ADDR_P0-1	x00 = 0xe7e7e7e7e7 0xf0f0f0f0d2
RX_ADDR_P2-5	x00 = 0xc3 0xc4 0xc5 0xc6
TX_ADDR		 = 0xe7e7e7e7e7
RX_PW_P0-6	x00 = 0x00 0x20 0x00 0x00 0x00 0x00
EN_AA		 = 0x3f
EN_RXADDR	x00 = 0x03
RF_CH		 = 0x4c
RF_SETUP	x00 = 0x07
CONFIG		 = 0x0f
DYNPD/FEATURE	x00 = 0x00 0x00
Data Rate	 = 1MBPS
Model		 = nRF24L01+
CRC Length	 = 16 bits
PA Power	 = PA_HIGH

[Fabien]

I have a batch of 5 sensebender and actually I build 3 and one of them doesn't work properly. Lot of st:fail when I put my finger on the board it works better so I try to make all solder one more time but it's not ok. I try with few radios and same radios work well on the others sensbender.
Any idea or way to exchange with Itead ?

[tbowmo]

@Fabien

Where exactly do you put your finger on it, in order to get it working?

[tbowmo]

@gloob

It's the same power rail (FTDI, and the battery connector). What do you supply the board with, thru the FTDI header?

[Fabien]

@tbowmo difficult to answer this question. It seems to be on Atmega but after trying to resold it's not better. I resol capacitors, resistors ... I don't know what to do now ...

[tbowmo]

@Fabien

Did you also resolder the atmega itself?

Could you try and measure supply current it uses?

[Fabien]

current when powering on : 20 mA and during sleeping about 20uA (not very accurate).

[tbowmo]

@Fabien

Have you tried to add an extra capacitor to the NRF module, on the one that's bad? (Could be your finger adds a bit more capacitance, I know it's a wild guess but just trying to think out loud)

[Fabien]

Ok but wich value ? I just finish to solder my 4th sensebender and ok too.

[hek]

Does the failed messages reach their destination (gateway in your case)? As you might know it is the ack that never reaches the sensbender node which could be a result of power issues on the gateway side.