find parent [solution found]



  • Hi all,

    i just built a motion, lux and dimmer sensor. The sketch is working perfeclty on a UNO+breadboard but does not seem to work on a pro mini+hardwired, i check the wiring already twice...
    The error i get in serial consol is:

    " find parent"

    what could be the trigger for this?
    thanks



  • try to delete eeprom of gateway and node...



  • just tried cleared the sensors eeprom, did not show any difference.
    As the "find parent" is the only line in the serial consol, do you think it can be related to the gateway?



  • this is my sketch:

    #include <SPI.h>
    #include <MySensor.h>  
    #include <BH1750.h>
    #include <Wire.h> 
    
    
    #define NODE_ID 136
    
    unsigned long SLEEP_TIME = 10000; // Sleep time between reports (in milliseconds)
    #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
    #define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
    #define LED_PIN 5      // Arduino pin attached to MOSFET Gate pin
    #define FADE_DELAY 25  // Delay in ms for each percentage fade up/down (10ms = 1s full-range dim)
    #define PIR_ID 0   // Id of the sensor child
    #define DIM_ID 1  // Id of the sensor child
    #define CHILD_ID_LIGHT 2
    boolean lasttripped = false;
    
    BH1750 lightSensor;
    MySensor gw;
    
    
    MyMessage msg(CHILD_ID_LIGHT, V_LIGHT_LEVEL);
    // MyMessage msg(CHILD_ID_LIGHT, V_LEVEL);  
    uint16_t lastlux;
    MyMessage pirMsg(PIR_ID, V_TRIPPED);
    // Initialize Dimmer
    static int currentLevel = 0;  // Current dim level...
    MyMessage dimmerMsg(DIM_ID, V_DIMMER);
    MyMessage lightMsg(DIM_ID,  V_LIGHT);
    
    void setup()  
    { 
      gw.begin(incomingMessage, NODE_ID, false);
    
      // Send the sketch version information to the gateway and Controller
      gw.sendSketchInfo("PIR & DIM & LUX", "1.0");
    
      // Register all sensors to gateway (they will be created as child devices)
      gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
      gw.present(DIM_ID, S_DIMMER );
      gw.request(DIM_ID, V_DIMMER );
    
        pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
      // Register all sensors to gw (they will be created as child devices)
      gw.present(PIR_ID, S_MOTION);
      
      lightSensor.begin();
    }
    
    void loop()      
    {   
     gw.process();
       boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
        if (lasttripped != tripped) {
        lasttripped = tripped; 
      Serial.print("PIR ");        
      Serial.println(tripped);
      gw.send(pirMsg.set(tripped?"1":"0"));  // Send tripped value to gw 
        }
    
        
      uint16_t lux = lightSensor.readLightLevel();// Get Lux value
      
      if ((round(lux/25))*25 != lastlux) {
        Serial.print("LUX ");
        Serial.println(lux);
          gw.send(msg.set(lux));
          lastlux = (round(lux/25))*25;
      }
      
    }
    void incomingMessage(const MyMessage &message) {
      if (message.type == V_LIGHT || message.type == V_DIMMER) {
        
        //  Retrieve the power or dim level from the incoming request message
        int requestedLevel = atoi( message.data );
        
        // Adjust incoming level if this is a V_LIGHT variable update [0 == off, 1 == on]
        requestedLevel *= ( message.type == V_LIGHT ? 100 : 1 );
        
        // Clip incoming level to valid range of 0 to 100
        requestedLevel = requestedLevel > 100 ? 100 : requestedLevel;
        requestedLevel = requestedLevel < 0   ? 0   : requestedLevel;
        
        Serial.print( "Changing level to " );
        Serial.print( requestedLevel );
        Serial.print( ", from " ); 
        Serial.println( currentLevel );
    
        fadeToLevel( requestedLevel );
        
        // Inform the gateway of the current DimmableLED's SwitchPower1 and LoadLevelStatus value...
        gw.send(lightMsg.set(currentLevel > 0 ? 1 : 0));
    
        // hek comment: Is this really nessesary?
        gw.send( dimmerMsg.set(currentLevel) );
    
        
        }
    }
    
    /***
     *  This method provides a graceful fade up/down effect
     */
    void fadeToLevel( int toLevel ) {
    
      int delta = ( toLevel - currentLevel ) < 0 ? -1 : 1;
      
      while ( currentLevel != toLevel ) {
        currentLevel += delta;
        analogWrite( LED_PIN, (int)(currentLevel / 100. * 255) );
        delay( FADE_DELAY );
      }
    }
    
    


  • found it, it was a not stable 3.3V for the radio... 😞 added a cap now everything works!
    topic can be closed



  • @jeti said:

    found it, it was a not stable 3.3V for the radio... 😞 added a cap now everything works!
    topic can be closed

    Thanks...you pushed me in the right direction! Same issue with the same solution here!


Log in to reply
 

Suggested Topics

  • 3
  • 2
  • 1
  • 2
  • 10
  • 3

26
Online

11.2k
Users

11.1k
Topics

112.5k
Posts