My Slim 2AA Battery Node

[kr0815]

yes, that´s 30 sensors you could build then

[GertSanders]

@nikos1671 If you buy the proto pack you could get 9,10 or 11 boards. It could be different that exactly 10 boards. In my case I received 12 boards for my design, in another order I received 11 boards. My last order was 10 boards. But in any case you will be able to make more then 25 sensors. Plenty for a normal house.

[rsachoc]

@dakky said:

Anyone want to share some photos with sensors assembled?
Any experiences how long this node will last? I have one DHT11 and one BH1750 onboard and will wake up the node every 5-15 Minutes.

Greetings
Dakky

I would like this too please! I'm trying to decide on which node to use as a motion sensor and temp/humidity sensor and would like to understand how I add a temp/humidty sensor to these and also the battery drain. And also, what temp/humidity sensors are we able to use with this node? I guess it ouputs max 3v, so does that mean the DHT11 and DHT22 are not able to be used here? Sorry for the newbie questions, I'm beginning to explore my options in relation to building my initial temp/humidity sensor and then a motion sensor.

edit OK, so based on what m26872 said here (http://forum.mysensors.org/topic/2715/slim-node-as-a-mini-2aa-battery-pir-motion-sensor/5) I think that I can only use Si7021 or HTU21 sensors as this outputs around 3v? From reading the spec sheet of the DHT11 and 22 I see they need 3.7v, so I guess if I want to use those sensors I need this node (http://forum.mysensors.org/topic/486/my-2aa-battery-sensor)?

[m26872]

@rsachoc Yep, you got it right.

[dakky]

Arghls no DHT11 with this node? Dammit. But a step up converter should do it?

[m26872]

Humidity Sensor example
http://forum.mysensors.org/topic/3049/slim-node-si7021-sensor-example

(This post used to contain a not yet finished design by mistake. The link above now shows the correct finished project.)

[m26872]

Reed Switch example
With external 10M pull-up to save battery. The plastic foam is used instead of a fixed mount, for easy disassemble, reflash, battery renewal etc.

The Sketch

// EgSlimReed2
// By m26872, 2015-12-22
// Interrupt driven binary switch for Slim Node with Reed switch and external pull-up (10Mohm)
// Inspired by mysensors example:
// https://github.com/mysensors/Arduino/blob/master/libraries/MySensors/examples/BinarySwitchSleepSensor/BinarySwitchSleepSensor.ino

#include <MySensor.h>
#include <SPI.h>
#include <Vcc.h>

#define NODE_ID 5 //12 var senaste "reed-node"-id // 110    // Use static Node_ID  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
#define SKETCH_NAME "EgSlimReed"
#define SKETCH_VERSION "2.0 2015-12-22"
#define SW_CHILD_ID 5
#define SW_PIN 3
#define BATTERY_REPORT_DAY 2   // Desired heartbeat interval when inactive. Maximum heartbeat/report interval is equal to this due to the dayCounter.
#define BATTERY_REPORT_BY_IRT_CYCLE 10  // Adjust this according to usage frequency.
#define ONE_DAY_SLEEP_TIME 86400000
#define VCC_MIN 1.9
#define VCC_MAX 3.3

int dayCounter = 0;
int irtCounter = 0;
uint8_t value;
uint8_t sentValue=2;
bool interruptReturn=false;
 
Vcc vcc;
MySensor gw;
MyMessage msg(SW_CHILD_ID, V_TRIPPED);

void setup()  
{  
  delay(100); // to settle power for radio
  gw.begin(NULL,NODE_ID);
  pinMode(SW_PIN, INPUT);
  digitalWrite(SW_PIN, LOW);    // Disable internal pull-ups
  gw.sendSketchInfo(SKETCH_NAME, SKETCH_VERSION);
  gw.present(SW_CHILD_ID, S_DOOR);  
}

void loop() 
{
  if (!interruptReturn) { // Woke up by timer (or first run)
	dayCounter++; 
	if (dayCounter >= BATTERY_REPORT_DAY) {
		  dayCounter = 0;
		  sendBatteryReport();
	}
  }
  else {	// Woke up by pin change
	  irtCounter++;
	  gw.sleep(50);  	  // Short delay to allow switch to properly settle
	  value = digitalRead(SW_PIN);
	  if (value != sentValue) {
		 gw.send(msg.set(value==HIGH ? 1 : 0));
		 sentValue = value;
	  }
	  if (irtCounter>=BATTERY_REPORT_BY_IRT_CYCLE) {
		irtCounter=0;
		sendBatteryReport();
	  }
  }

  // Sleep until something happens with the sensor,   or one sleep_time has passed since last awake.
  interruptReturn = gw.sleep(SW_PIN-2, CHANGE, ONE_DAY_SLEEP_TIME);

} 

void sendBatteryReport() {
		  float p = vcc.Read_Perc(VCC_MIN, VCC_MAX, true);
		  int batteryPcnt = static_cast<int>(p);
		  gw.sendBatteryLevel(batteryPcnt);
}

[m26872]

Motion sensor example
As already mentioned; more details to be found here.http://forum.mysensors.org/topic/2715/slim-node-as-a-mini-2aa-battery-pir-motion-sensor

[dakky]

do u add these photos and comments to openhardware.io ? they are quite helpful

[AWI]

@m26872 I don't use any I2C pull-ups. All my Si7021/ SHT21 (GY-21) boards include the SDA/SCL pull-ups (and LDO voltage regulator/ level conversion).

[m26872]

@AWI
Oops, it makes me worried that I completely forgot that this project was in some test stage. Ldo and everything should probably be bypassed, but I wanted to test it first. Post edited. Thanks for noticing!

And sorry for everyone else if this caused any trouble.

(It also makes me a little worried about that I have too many ongoing projects right now. )

[rsachoc]

@AWI said:

@m26872 I don't use any I2C pull-ups. All my Si7021/ SHT21 (GY-21) boards include the SDA/SCL pull-ups (and LDO voltage regulator/ level conversion).

@m26872 said:

@AWI
Oops, it makes me worried that I completely forgot that this project was in some test stage. Ldo and everything should probably be bypassed, but I wanted to test it first. Post edited. Thanks for noticing!

And sorry for everyone else if this caused any trouble.

(It also makes me a little worried about that I have too many ongoing projects right now. )

Apologies again, so that I understand it, does that mean when adding the mentioned temp sensor nodes I need additional parts?

[m26872]

@rsachoc My mistake and my apology. Unfortunatly I can't even finish and share the resluts from that humidity sensor in a while since I'm leaving for a few weeks holiday.

Anyway
@riataman Shows a mod of the GY-21 board in this post. He also link to a board without the LDO and level converter. In any case you wont need the two 4k7 pull-up in my pictures above, only if use the bare chip.

[ahmedadelhosni]

What about using a hall effect sensor to detect magnet ?

I have a door sensor using the same contact sensor, but I also have a hall effect sensor and I hope to test it soon. It is very small compared to the contact sensor.

[sensorchecker]

Hello m26872,
your project is great, and i will order tomorrow a set of PCBs.
I've done a breadboard setup with the SI7021 according to your schematic and your sketch, which works flawlessly.
(ATmega328P / SI7021 / NRF24L01 / 2xAA Battery / your 1Mhz bootloader / your Fuse Settings)

Unfortunately I do not get the current consumption below 2mA.
What to do to get the power consumption below 10uA and to increase the battery life on a couple of years ?
Any help is appreciated...

[AWI]

@sensorchecker A power consumption of 2mA is way out of range. Is your sensor entering sleep? Or an ftdi adapter still connected?

[arnoldg]

can i run it on 5V without any problem.

For the RF433 interface i need 5V so i would like to make one that is powerd by an usb charger.

[sensorchecker]

@AWI

No FTDI Adapter, no LED and nothing else is connected.
I build the node like the schematic in the first post.
When i start the sensor node, power consumption is about 16mA.
After a few seconds (4-5sec) the current goes down to 2mA

Can you please tell me, how to find out, that the node is in sleep mode
I have really no idea how to fix that.. but i have to, because i ordered the PCBs today!

Thanks for your help

[m26872]

@sensorchecker I think you should start with a simple example like the "reed switch sensor" and by looking at the other sketches you should be able to add some debug prints yourself. You only need a high ohm resitor 1M-10M and two pieces of wire to simulate a button or switch.

[m26872]

@arnoldg The nRf24L01+ is rated like 1.9-3.7V. So 5V will probably kill it.

[arnoldg]

Oke, that's tru i didn't think of that.
but when i use a 5v - 3v power suply in between it could work.

[sensorchecker]

@m26872
I have already tested the "reed switch sensor" and it works fine for me- but with a power consumption of 2mA ...:-(
Is it possible that i have a problem with the bootloader or the fuses ?
How can i check that ?
Usually i use USBASP and avrdude for programming the processors on breadboards.
Is it also possible to do the whole programming with the arduino IDE ?

[ahmedadelhosni]

@sensorchecker did you try changing your nrf ?

[BartE]

@sensorchecker and @m26872 changing the NRF module did work for me as well.

I was struggling a lot getting the power consumption down using all the trick and tips as described on the mysensors forum but nothing worked for by battery powered nodes (i have a couple these ).

I was not able to bring the power consumption down below 2.4 mA (with the NFR mounted) finally i just, for an differnt experiment, i took a "fresh"NRF and just for the fun i measured the current and it was down to 0.05 mA for no reason. They came from the same batch.

My theory now is that i broke the first radio module during programming of the node, although the FTDI serial module is in 3.3v mode it still measures around 4.5 volt. So the voltage might has damaged my NRF radio a bit (it still communicates).

[sensorchecker]

@ahmedadelhosni and @BartE and @m26872 you made my day...!
Changing the NRF module was the solution, now my power consumption is about 8uA.
Now waiting for the PCBs and parts to build 10- 15 nodes

Thank you so much for your help

[flopp]

There is no crystal?

I haven't used Atmega328P as standalone but I have read that you need a crystal.

[m26872]

@flopp There's an internal 8MHz xtal in the uC. Infact often default set to be used by factory "fuse" settings. It's not as ambient condition stable and accurate as an external crystal, but quite good enough for our application.

[flopp]

@m26872 thanks

[flopp]

What about these pF caps, why not use SMD tantalum instead of Solid electrolyte with legs?

Or can I use ATmega without caps, since I dont have an external crystal?

[m26872]

@flopp I doubt there are any electrolytes in the pF range seen here. If you mean the pF caps in the example pictures, they are not part of the Slim Node base concept and just a random choice I did for myself. If you mean all the 100nF caps in the base concept, it's a matter of the "smd free" design criteria I apply from time to time.

[m26872]

@flopp ... or if you refer to the standard pair of 22pF caps used when there is an external crystal - no, you wont need them.

[flopp]

@m26872 said:

@flopp I doubt there are any electrolytes in the pF range seen here. If you mean the pF caps in the example pictures, they are not part of the Slim Node base concept and just a random choice I did for myself. If you mean all the 100nF caps in the base concept, it's a matter of the "smd free" design criteria I apply from time to time.

OK. Yes, I saw that there was cap in pictures.

[flopp]

@m26872 said:

@flopp ... or if you refer to the standard pair of 22pF caps used when there is an external crystal - no, you wont need them.

OK, perfect

[meddie]

Hi together,

as first i have to say, its a nice node, that you build.
So i tried to build one. I ordered an atmega 328p. Flashed the bootloader from the forum. This is the boards.txt:

atmega328_1mhz_4800baud.name=ATmega328 on a breadboard 1MHz internal clock, fast start, 1.8V BOD, 4800baud upload

atmega328_1mhz_4800baud.upload.protocol=arduino
atmega328_1mhz_4800baud.upload.maximum_size=32256
atmega328_1mhz_4800baud.upload.speed=4800

atmega328_1mhz_4800baud.bootloader.low_fuses=0x42
atmega328_1mhz_4800baud.bootloader.high_fuses=0xDE
atmega328_1mhz_4800baud.bootloader.extended_fuses=0x06

atmega328_1mhz_4800baud.bootloader.file=atmega/atmega328_1b.hex
atmega328_1mhz_4800baud.bootloader.unlock_bits=0x3F
atmega328_1mhz_4800baud.bootloader.lock_bits=0x2F

atmega328_1mhz_4800baud.build.mcu=atmega328p
atmega328_1mhz_4800baud.build.f_cpu=1000000L
atmega328_1mhz_4800baud.build.core=arduino:arduino
atmega328_1mhz_4800baud.build.variant=arduino:standard


atmega328_1mhz_4800baud.bootloader.tool=arduino:avrdude
atmega328_1mhz_4800baud.upload.tool=arduino:avrdude

Now i have measured the current draw, and the arduino alone draws 6.8mA (without crystal, nrf ...)
I tried some sketches, (binaryswitchsleepsensor) but the current is not really gone down.
The only sketch is this:

// **** INCLUDES *****
#include "LowPower.h"

void setup()
{
    // No setup is required for this library
}

void loop() 
{
    // Enter power down state for 8 s with ADC and BOD module disabled
    LowPower.powerDown(SLEEP_8S, ADC_OFF, BOD_OFF);  
    
    // Do something here
    // Example: Read sensor, data logging, data transmission.
}

With this sketch is the current 0.02mA

OK, 0.02mA is not bad, but when i read that some of you have few µa, i dont understand why the current on my atmega is so "high"

Can somebody tell me what bootloader is good, wich fuses are good. And maybe what i have to do to get the current so small as possble

Thank you very much
Greets Eddie

[m26872]

@meddie I don't really get what you've ruled out in your troubleshooting. Do you "test the arduino alone" using MySensors lib and example sketches? Using Lowpower lib directly works ok as it seems. Next step would be to connect the nRF24L01+ and run some MySensors lib example.

Ext fuses 0x07 (BOD disabled) instead of 0x06 (BOD 1.8V) could save you a few uA.

[meddie]

@m26872 said:

Do you "test the arduino alone" using MySensors lib and example sketches?

Yes, on the bredboard is only the atmega 328p. nothing else. Connected to 5v

Using Lowpower lib directly works ok as it seems.

Yes using the LowPower lib i came down to 0.01mA current draw.

Next step would be to connect the nRF24L01+ and run some MySensors lib example.

Ok, i will try it today evening.

Ext fuses 0x07 (BOD disabled) instead of 0x06 (BOD 1.8V) could save you a few uA.
OK, i try this too.

Thank you very much.
Greets Eddie

[meddie]

ok, i tried to burn with 0x07 Fuse. And i tried to power the atmega with 3.3 v and not 5v.
Now i came down to 4µA in sleep mode with the lowpower sketch.
When i try to flash a mysensors sketch the the atmega has a current draw 1mA.

[m26872]

@meddie It's still unclear whether you've got the nRF connected and the MySensors example and library fully working (sleeping) before you measure.

[ar91]

@meddie If you have a extra nRF try using that, i had a similar issue and i tried replacing the nRF and it came from mA to uA.

[meddie]

yes of course, i just connected a nrf to the atmega an uploaded the binaryswitchsleepsensor sketch. Now i have a current draw 95.6µA
But when i take the door contact off the atmega draws only 1.3µA
When the door contact is closed (from 3 to GND) the the current is rising to 95.6µA

[GertSanders]

Makes sense to me. By closing the contact you get a path from 3V3 via the pullup resistor to ground.

The current is (for a pullup resistor value around 30KOhm) around 100uA.

Try NOT using the internal pullup resistor of pin D3, and using an external pullup resistor of 1MOhm or more.

You will see lower current when the contact is closed.

[meddie]

ok, i dont have 1mohm here. but i just ordered them. When i get them i will try out and will write here.
Thynk you very much for your help.
Great Forum! Great Projekt!
Greets Eddie

[Pierre P]

Hello,
This board is GREAT. But why C5 ave to be different from C1 C2 C3 ?

[m26872]

@Pierre-P I haven't verified the benefits of C5, so it's just theoretical. You could probably omit or replace without any significant difference.

Anyway, the reasons behind are seen in the BOM. 1 - Package (under uC socket). 2 - RF performance (single layer).

[Pierre P]

@m26872 I see it in the BOM. But now, i can't see where it goes (5 hours... I ask a question, and 5 hours later I can't see what i was talking about....)

C4 is cool for the NRF pic of tension, but -just for information- it could be wherever between 0Vcc and 5Vcc, not necessarily near the NRF ?

As an electrician, and not an electronician, I don't understand why so many 0.1uF capacitor are needed (but i put them too) as we can see in MySlimNode2-sch.pdf that they are virtually at the same place...

Thanks for the answer !

[wergeld]

@m26872 I am about to order the v2 version of the board and I have a few questions as I have never ordered PCBs before.
The defaults on ordering are:
layers - 2
thickness - 1.2 mm
coating - HASL
stencil - none

What are these options? I am tempted to just order as-is...for $14 what could I complain about? I am just curious what these other options are for.

[m26872]

@wergeld
Layers - The board is designed with 2 copper layers (top and bottom) so you can't change that.
Thickness - Of your taste. Default is well proven but e.g. a little thinner could make it easier when you break the panelizing cuts.
Coating and stecil - Honestly I've never bothered to look them up. But google is your friend if you put PCB before as keywords.

[ahmedadelhosni]

Hello @m26872 it is me again if you do remember me.

Just wanted to tell you that I ordered the boards 5 weeks ago and it was delivered to Egypt after 2 weeks, and the silly customs requested some security approvals to give me the boards which I couldn't do it till now. Something pathetic which makes me laugh

Can't wait to do my nodes !

[m26872]

@ahmedadelhosni Welcome back! Yes I remember you had to struggle and could not buy common 433MHz remote controlled switches. Makes sense to do diy projects then I guess.
Hope you get your new nodes running. Please share your result.

[ahmedadelhosni]

@m26872 You are right.

I'll go tomorrow and try to get the approval Well back soon

[ahmedadelhosni]

Finally !

11 pcbs. But I am really angry and feel bad from what happened by DHL.
I paid 29$ for shipping and here in Egypt i paid stupid fees for customs and several things equal to 38$ !!!!! I dont know wether this is something related to my country Egypt or not

I' ll try to forget all what I paid when I do my first node.

[ericvdb]

@ahmedadelhosni that really sucks

[betonishard]

Hello all,

I have been struggling with this for a couple of weeks now and I just can seem to figure out a good way to upload sketches to the arduio328p-pu. First of all I use this setup;

I use arduino for mac 1.6.5
I use a breadboard with a crystal, two capacitors and a resistor between reset and 5v.
An arduino to burn bootloader (with the chip inserted and sketch arduinoISP uploaded).
I use the same hex files as you guys with 1a. I used the optiboot 9600 BOD, just the 9600 and the 4800. Uploading the bootloader is no problem at all. Arduino ide burns the bootloader without any problems. However when I try to upload the sketches I get different errors. The “Yikes” version in which it states that my device signature is not ok and programmer not responding. I use upload using programmer.

So, I tried to upload the arduino uno version to rule out all miscabling. So what I did was upload the arduino uno bootloader, tried to upload the blink sketch afterwards and it works. So my cables are ok….

I thought to repeat the exact same process with the boot version above. However no succes, I keep getting stuck at uploading sketches. Is it just not possible?

I read about setting the fuse options and I read that when you define these in the boards.txt, they will be set as the fuseparameters. When I check the boards txt above i see that fuse settings are: L0x62,H0xde,E0x07, however when I open the png file (first post, fuse settings) it states L0x62,H0xDE,E0xFF. Furthermore the lockbits are at 0xCF, compared to the boards.txt 0x2F. What is true and how should I set these. I don’t see a possibility in arduino ide (I use another arduino to upload, so I don’t have a tiny or USBASP.

Help would be much appreciated here because I have like 30 boards sitting catching dust.

[scalz]

@ahmedadelhosni : no luck! Here same for us in France. I think it's because they handle our package from airport to house...but have we not already paid for this! There is vat of course too, but here vat+15euro extra mystical handle fee.
Fun, is when you want to make a joke to the dhl person and you ask why fees, I don't want pay, give me my package, no come back!! ahaha they are not funny At less, if they were doing right their job, 4times/10 they say "you were not here"??? yep, but I was there..and where is the paper in my mailbox, nothing...arrgh! what do you think I will wait you on the road???

No matter, looking at your package, I think you will have lot of fun

[ahmedadelhosni]

@scalz Seeing that someone else had the same issue made me better hahaha
The problem that I went myself to take it today and they told me that I have to buy for the customs and the government.

I need to calm down and have fun better. Thanks

[m26872]

@betonishard A few "unused" bits of the Ext fuses are differently written in avrdude (Arduino IDE) and Atmel IDE programmer implemetation. That's why the same settings can look different. You have to know which one you use.
Search for "Avr fuse calculator" on the internet and some will show you fuses for both methods.

I also had issues with avrdude when I started and never got it to work. A lot of others do of course, but I found the Atmel way easier for me. Hence only this is shown in the pictures. The bootloading business is not easy and a lot of info is availible on the arduino forums. I think the only way is to read and study.

[meddie]

@betonishard said:

Hello all,

I have been struggling with this for a couple of weeks now and I just can seem to figure out a good way to upload sketches to the arduio328p-pu. First of all I use this setup;

I use arduino for mac 1.6.5
I use a breadboard with a crystal, two capacitors and a resistor between reset and 5v.
An arduino to burn bootloader (with the chip inserted and sketch arduinoISP uploaded).
I use the same hex files as you guys with 1a. I used the optiboot 9600 BOD, just the 9600 and the 4800. Uploading the bootloader is no problem at all. Arduino ide burns the bootloader without any problems. However when I try to upload the sketches I get different errors. The “Yikes” version in which it states that my device signature is not ok and programmer not responding. I use upload using programmer.

So, I tried to upload the arduino uno version to rule out all miscabling. So what I did was upload the arduino uno bootloader, tried to upload the blink sketch afterwards and it works. So my cables are ok….

I thought to repeat the exact same process with the boot version above. However no succes, I keep getting stuck at uploading sketches. Is it just not possible?

I read about setting the fuse options and I read that when you define these in the boards.txt, they will be set as the fuseparameters. When I check the boards txt above i see that fuse settings are: L0x62,H0xde,E0x07, however when I open the png file (first post, fuse settings) it states L0x62,H0xDE,E0xFF. Furthermore the lockbits are at 0xCF, compared to the boards.txt 0x2F. What is true and how should I set these. I don’t see a possibility in arduino ide (I use another arduino to upload, so I don’t have a tiny or USBASP.

Help would be much appreciated here because I have like 30 boards sitting catching dust.

Hi, i had the same problem, but then i tried the 1b hex and since i burned this it works for me.

[meddie]

@GertSanders said:

Makes sense to me. By closing the contact you get a path from 3V3 via the pullup resistor to ground.

The current is (for a pullup resistor value around 30KOhm) arounda lot of 100uA.

Try NOT using the internal pullup resistor of pin D3, and using an external pullup resistor of 1MOhm or more.

You will see lower current when the contact is closed.

Yesterday i get a lot of resistors, now i testen 1Mohm and the current draw is around 4 µa, but now the arduino do not recognize when the reedcontact is closed or open. When the contact is closed the current draw is 4 µa when opened 1.2µa
do i have to edit the sketch in order to get it to work?

[GertSanders]

@meddie
The pull up 1MOhm resistor should go from Vcc - resistor - D2
The switch should be connected to D2 and Gnd
D2 needs to be defined as INPUT, no need to add the statement with PULLUP.
Post your sketch so we can have a look.

[meddie]

/**
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Interrupt driven binary switch example with dual interrupts
 * Author: Patrick 'Anticimex' Fallberg
 * Connect one button or door/window reed switch between 
 * digitial I/O pin 3 (BUTTON_PIN below) and GND and the other
 * one in similar fashion on digital I/O pin 2.
 * This example is designed to fit Arduino Nano/Pro Mini
 * 
 */


#include <MySensor.h>
#include <SPI.h>

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define SECONDARY_CHILD_ID 4

#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
#endif
#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
#endif
 
MySensor sensor_node;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);
MyMessage msg2(SECONDARY_CHILD_ID, V_TRIPPED);

void setup()  
{  
  sensor_node.begin();

  // Setup the buttons
  pinMode(PRIMARY_BUTTON_PIN, INPUT);
  pinMode(SECONDARY_BUTTON_PIN, INPUT);

  // Activate internal pull-ups
  digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
  digitalWrite(SECONDARY_BUTTON_PIN, HIGH);
  
  // Send the sketch version information to the gateway and Controller
  sensor_node.sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER"."SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sensor_node.present(PRIMARY_CHILD_ID, S_DOOR);  
  sensor_node.present(SECONDARY_CHILD_ID, S_DOOR);  
}

// Loop will iterate on changes on the BUTTON_PINs
void loop() 
{
  uint8_t value;
  static uint8_t sentValue=2;
  static uint8_t sentValue2=2;

  // Short delay to allow buttons to properly settle
  sensor_node.sleep(5);
  
  value = digitalRead(PRIMARY_BUTTON_PIN);
  
  if (value != sentValue) {
     // Value has changed from last transmission, send the updated value
     sensor_node.send(msg.set(value==HIGH ? 1 : 0));
     sentValue = value;
  }

  value = digitalRead(SECONDARY_BUTTON_PIN);
  
  if (value != sentValue2) {
     // Value has changed from last transmission, send the updated value
     sensor_node.send(msg2.set(value==HIGH ? 1 : 0));
     sentValue2 = value;
  }

  // Sleep until something happens with the sensor
  sensor_node.sleep(PRIMARY_BUTTON_PIN-2, CHANGE, SECONDARY_BUTTON_PIN-2, CHANGE, 0);
} ```

[GertSanders]

@meddie said:

// Activate internal pull-ups
digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
digitalWrite(SECONDARY_BUTTON_PIN, HIGH);

If you use the external pull up, you need to comment out these two lines like so:

// Activate internal pull-ups
// digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
// digitalWrite(SECONDARY_BUTTON_PIN, HIGH);

No need for an internal pullup if you use an external pull up.
In the above I'm assuming you have an external pullup resistor for each digital pin, one for D2 and one for D3.

[ahmedadelhosni]

@m26872 said:

@ahmedadelhosni You know that the nRF pins are not centered? That means if you rotate it like this it will no longer be straight above the "slim node motherboard".
What height do you expect it to be?

I understood now what you meant by "not centered". Thanks for notifying me.
I'll take care of that.

[betonishard]

@meddie are you also using the optiboot 9600 NOBOD in boards.txt the same as in the first post (fuse settings I mean)? And are you using avrdude arduino ide for mac?

I tried your solution but i get the same results.. Yikes!

If you use the same setup, can you post your boards.txt? Did you also make changes to the hex file?

Thanks in advance.

[betonishard]

@m26872 Thanks for your answer... The problem is I read a lot about it (which makes me kinda stupid that I still haven't achieved this).

I tried to find atmel studio (I believe you are referring to atmel studio?) I couldn't find a proper mac version. I checked on the fuse calculator and still no success. Maybe some one could give me the correct fuse settings for AVR or a proper mac download link for atmel studio.

OI know I am asking a lot, but it would help me a lot. Thanks.!!

[m26872]

@betonishard Yes, of course ask if you have problem. But I suggest you also make a new separate thread in General-, Hw- or Troubleshooting section about your issues.
Maybe it's a good idea to ask in arduino forum as well.

[ahmedadelhosni]

Hello @m26872

I succeeded now to burn the bootloader which you used (1Mhz). I just don't understand a phrase which you mentioned above.

According to this you should use minimal startup time to reduce power in every 8s sleep cycle, but for the moment I don't care and stick to the default 65ms.

Can you explain what is this ? and whether it is affecting badly on something or not ?

Thanks..

[meddie]

its the fuse, which defines the rising time. the oscillator needs some time to come to the correct frequency. If you dont wait this time its possble that your sketch dont work correctly. But the microcontroller is the 65 ms longer not in sleep mode and need more battery power. but works more stable.

[meddie]

YEAH, YEAH YEAH! Thank you all for the help a big thanks to GertSanders. Now it seems to work perfectly. The current draw is now 4.6µa. Now i have to transfer from bredboard to pcb.
Thank you very much!!!!!!

[meddie]

Here

@betonishard said:

@meddie are you also using the optiboot 9600 NOBOD in boards.txt the same as in the first post (fuse settings I mean)? And are you using avrdude arduino ide for mac?

Hi no i use the ide for Windows i dont have a mac.

Here is the hex File

:107E0000112484B714BE81FFE6D085E08093810001
:107E100082E08093C00088E18093C10086E0809377
:107E2000C20089E18093C4008EE0BFD0259A86E02D
:107E300023EC3FEF91E0309385002093840096BBC4
:107E4000B09BFECF1D9AA8958150A9F7EE24FF2480
:107E5000AA24A394B5E0CB2EA1E1BA2EF3E0DF2E45
:107E600098D0813461F495D0082FA5D0023829F13B
:107E7000013811F485E001C083E083D07FC08234F3
:107E800011F484E103C0853419F485E09CD076C0F8
:107E9000853579F47ED0E82EFF247BD0082F10E0C2
:107EA000102F00270E291F29000F111F84D07801E1
:107EB00065C0863521F484E086D080E0DECF84364C
:107EC00009F040C066D065D0082F63D080E0E81686
:107ED00080E7F80618F4F701D7BEE895C0E0D1E0D6
:107EE00058D089930C17E1F7F0E0EF16F0E7FF06A2
:107EF00018F0F701D7BEE8955ED007B600FCFDCFBD
:107F0000A701A0E0B1E02C9130E011968C9111977F
:107F100090E0982F8827822B932B1296FA010C0160
:107F2000A7BEE89511244E5F5F4FF1E0A038BF0770
:107F300051F7F701C7BEE89507B600FCFDCFB7BE05
:107F4000E8951CC0843761F424D023D0082F21D0B9
:107F500032D0F70185917F0114D00150D1F70EC0C6
:107F6000853739F428D08EE10CD085E90AD08FE02E
:107F700084CF813511F488E018D01DD080E101D084
:107F80006FCF982F8091C00085FFFCCF9093C600E3
:107F900008958091C00087FFFCCF8091C00084FDD0
:107FA00001C0A8958091C6000895E0E6F0E098E150
:107FB000908380830895EDDF803219F088E0F5DF4B
:107FC000FFCF84E1DECF1F93182FE3DF1150E9F7D5
:107FD000F2DF1F910895282E80E0E7DFEE27FF27CC
:027FE000099402
:027FFE0000057C
:0400000300007E007B
:00000001FF

Just create a new txt file put this code in there and rename the file to atmega328_1b.hex

this is my boards.txt:

##############################################################

atmega328_1mhz_4800baud.name=ATmega328 on a breadboard 1MHz internal clock, fast start, 1.8V BOD, 4800baud upload

atmega328_1mhz_4800baud.upload.protocol=arduino
atmega328_1mhz_4800baud.upload.maximum_size=32256
atmega328_1mhz_4800baud.upload.speed=4800

atmega328_1mhz_4800baud.bootloader.low_fuses=0x42
atmega328_1mhz_4800baud.bootloader.high_fuses=0xDE
atmega328_1mhz_4800baud.bootloader.extended_fuses=0x07

atmega328_1mhz_4800baud.bootloader.file=atmega/atmega328_1b.hex
atmega328_1mhz_4800baud.bootloader.unlock_bits=0x3F
atmega328_1mhz_4800baud.bootloader.lock_bits=0x2F

atmega328_1mhz_4800baud.build.mcu=atmega328p
atmega328_1mhz_4800baud.build.f_cpu=1000000L
atmega328_1mhz_4800baud.build.core=arduino:arduino
atmega328_1mhz_4800baud.build.variant=arduino:standard


atmega328_1mhz_4800baud.bootloader.tool=arduino:avrdude
atmega328_1mhz_4800baud.upload.tool=arduino:avrdude

this worked for me!

[m26872]

@ahmedadelhosni I've never verified it by measuring, but I understood like @meddie about Gammons writing.
To get rid of those 65ms startup time you should use fuses 42-DE-FF (Lo-Hi-Ext) instead of 62-DE-FF.

If anyone could verify and measure current between sleep cycles and share some results, it would be great.

[betonishard]

@meddie and @all Tonight I think I have fixed my issue however how I do not understand so maybe someone can explain, or maybe I think I have fixed it and it is not fixed at all.

On the arudino website it states that when you burn your bootloader you have to connect pin 13,12,11 and pin 10 to reset (and ofcourse 5v and ground). AFter burning the bootloader you should replace it with the rx and tx cable and disconnect 13,12,11 and connect reset to reset. Each time I did this I got the error of Yikes! However tonight by accident I forgot to rewire the pins to rx and tx and press “Upload using programmer” all of a sudden it stated “done uploading”.

I tested this with blink sketch so I attached a led to pin13 and ground. The led started to blink. I was happy however did not understand…. or is this just a n00b mistake

[ahmedadelhosni]

@meddie said:

@betonishard said:

Hello all,

I have been struggling with this for a couple of weeks now and I just can seem to figure out a good way to upload sketches to the arduio328p-pu. First of all I use this setup;

I use arduino for mac 1.6.5
I use a breadboard with a crystal, two capacitors and a resistor between reset and 5v.
An arduino to burn bootloader (with the chip inserted and sketch arduinoISP uploaded).
I use the same hex files as you guys with 1a. I used the optiboot 9600 BOD, just the 9600 and the 4800. Uploading the bootloader is no problem at all. Arduino ide burns the bootloader without any problems. However when I try to upload the sketches I get different errors. The “Yikes” version in which it states that my device signature is not ok and programmer not responding. I use upload using programmer.

So, I tried to upload the arduino uno version to rule out all miscabling. So what I did was upload the arduino uno bootloader, tried to upload the blink sketch afterwards and it works. So my cables are ok….

I thought to repeat the exact same process with the boot version above. However no succes, I keep getting stuck at uploading sketches. Is it just not possible?

I read about setting the fuse options and I read that when you define these in the boards.txt, they will be set as the fuseparameters. When I check the boards txt above i see that fuse settings are: L0x62,H0xde,E0x07, however when I open the png file (first post, fuse settings) it states L0x62,H0xDE,E0xFF. Furthermore the lockbits are at 0xCF, compared to the boards.txt 0x2F. What is true and how should I set these. I don’t see a possibility in arduino ide (I use another arduino to upload, so I don’t have a tiny or USBASP.

Help would be much appreciated here because I have like 30 boards sitting catching dust.

Hi, i had the same problem, but then i tried the 1b hex and since i burned this it works for me.

@meddie @betonishard I guess I know the solution. Yesterday I begun creating my nodes with the same setup and faced the same issue. When You upload your sketch, choose your board, and the important thing which will solve the "Yikes" error, is to choose "Arduino as ISP" not "ArduioISP". You will find it under Tools > Programmer.

Another thing. If you are chip is the one which comes with the arduino UNO, then you have to add a crystal at the first time when you change the bootloader. According to what I read yesterday (and this solved an issue also which I faced) that the chip is already configured to use external crytsal. Thus (for the first time only), I tried adding a 20 Mhz, and 10Mhz as I didn't have 16Mhz, and surprisingly both configurations worked

let me know please if that helps.

[ahmedadelhosni]

@meddie THanks for the answer.

Can you please also explain your final result to reach 4uA. I have also the same problem and current is 90uA and sometimes drops to 20uA, then rises again. Thanks.

Edit: I figured out that I was using the 3.3v from arduino UNO. CHanged to two 1.5 batteries. THe current drops to 1.4uA when contact is open but sometimes it is also 15 uA. And when contact is closed it is 60 uA, and sometimes drops. Don't know why it is not stable.

Edit 26.1.2016: I managed to reach 1.4uA with door opened, and 15uA when closed. I guess the problem was with the wiring. DOn't really know but I used a battery holder instead. I will try to rechange the resistor value to 1Mohm and reupdate.

Edit 27.1.2016: ok I created another node and connected the contact sensor in series with the 1Mohm and the output is the voltage divider. now it is 1.4uA when open and 4.6uA when closed.

Thanks

[Pierre P]

@m26872 said:

Board releases:

• Version 2.0 (black) [order] Now designed in KiCad. Hopefully the "final" release.

Well, can I ask an update ? It's about the labels, couldn't we have them on the two faces ? It's always good to know where are Vcc and Gnd at first eye I think.
After all, the atmega and nrf are the only components that can't move to the other side. But even there, knowing the digital and analog pin should be useful !

[Cliff Karlsson]

My PCBs have just arrived and I was going to build a couple of sensors but can´t figure out the first part of how to burn the bootloaders.

For starters can I just use one of the PCBs and solder the atmega socket and a 6 pin header near the nrlf-radio headers? And use this with a Atmega-programmer ?or do I need to solder any more components?

I tried with both a usbasp and a USBtinyISP but could not get any new device to show up in the arduino IDE. But I don´t know if it is a software issue with win10 or if it is hardware related.

[Pierre P]

I've made it with that link: http://www.gammon.com.au/breadboard with no cristal.

[m26872]

@Cliff-Karlsson Apart from the 2x3pin AVRISP you also need to supply power (battery?) Maybe easiest by the 1x6pin FTDI Vcc and Gnd pins. No other components should be needed.

[m26872]

@Pierre-P said:

@m26872 said:

Board releases:

• Version 2.0 (black) [order] Now designed in KiCad. Hopefully the "final" release.

Well, can I ask an update ? It's about the labels, couldn't we have them on the two faces ? It's always good to know where are Vcc and Gnd at first eye I think.
After all, the atmega and nrf are the only components that can't move to the other side. But even there, knowing the digital and analog pin should be useful !

I think I'll collect "improvements" in a list. I agree that some labels could be added, but I don't think it's enough for a new board release.
Also the boardhouse credit collection (which becomes MySensors donations) will be scattered and smaller if there's many versions and branches.

[Cliff Karlsson]

@m26872 said:

AVRISP

Ok so the AVRISP does not provide any power even as it is self powered from usb?

[m26872]

@Cliff-Karlsson At least that's how my programmer works (Avrisp MkII). I think it's a thing to not interfere when it's programmed "in circuit".

[betgear]

@m26872. Thanks for the design, very nice.

On your posted picture of the GY-21, why have you added extra resistors? The Gy-21 has it's own pull ups 4.7k for the i2c bus, so additional resistors are not required!

I removed the voltage regulator from the gy-21 board as well (detailed elsewhere in the forum) to save a little extra power. The only caveat to this is you've got to remember to remove the radio and gy-21 when programming using the usbtinyisp or usbasp as they run at 5v which could damage them.

I'm using the (hallard) breakout board for the rfm69cw which has a much better range than the nrf24's (no idea why people use these unless they live in a rabbit hutch)

Anyway, thanks once again for sharing.

Glen.

[m26872]

@betgear If you had read the posts further down (just like the first line says), you would have seen that the discussion and explainations are already there. But thanks for sharing you results.

[m26872]

@betgear My guess is that the main reason for people to use nRF24 is because the MySensors support for RFm69 came rather recently.

Edit: For me it's the price. I buy 20(!!!) pcs nRF24 for the price of one RFm69. Main reason is different shipping costs.

[Cliff Karlsson]

I just need to ask one more time so that I am absolutley clear abot the bootloader burning. I still cant figure out how to do this with my USBtiny.

First of all my USBtiny provides 3.3 or 5v does it matter what voltage that I provide?
And If I just place the ISCP (?) header and atmega socket I do not need to solder any more components or provide any more power to make the circut complete?

[m26872]

@Cliff-Karlsson said:

First of all my USBtiny provides 3.3 or 5v does it matter what voltage that I provide?

No, as long as it's only the Atmega there.

And If I just place the ISCP (?) header and atmega socket I do not need to solder any more components or provide any more power to make the circut complete?

Yes, correct. (ICSP)

[m26872]

@Cliff-Karlsson Forgot to add that there is already a bootloader on that requires external crystal, you have to add it before to get it work.

[Cliff Karlsson]

Ok thanks for the info. So if I do not have any crystals it is not possible to burn the bootloader in any way?

[m26872]

@m26872 said:

@Cliff-Karlsson Forgot to add that IF there is already a bootloader on that requires external crystal, you have to add it before to get it work.

(the important word "if" dropped out. )

[m26872]

@Cliff-Karlsson said:

Ok thanks for the info. So if I do not have any crystals it is not possible to burn the bootloader in any way?

No, not if its fuses are set for external crystal.

[GertSanders]

An ATMEGA328 coming from ATMEL is normally set to use the internal oscillator and has no bootloader. You will then have no need to put a crystal.

I do this anyway on my breadboard (for the 28 pin DIP versions).

If you have the SMD version of the atmega328 (the AU variant), I'm assuming it is set in the same default state (no crystal needed, running on internal oscillator).

[ahmedadelhosni]

@Cliff-Karlsson i added 10 Mhz and it worked as I didnt have 16 Mhz. Also tested with 20Mhz and worked

[ahmedadelhosni]

First node. Door sensor.
Great boards :+

.

[meddie]

@ahmedadelhosni said:

@meddie THanks for the answer.

Can you please also explain your final result to reach 4uA. I have also the same problem and current is 90uA and sometimes drops to 20uA, then rises again. Thanks.

Edit: I figured out that I was using the 3.3v from arduino UNO. CHanged to two 1.5 batteries. THe current drops to 1.4uA when contact is open but sometimes it is also 15 uA. And when contact is closed it is 60 uA, and sometimes drops. Don't know why it is not stable.

Edit 26.1.2016: I managed to reach 1.4uA with door opened, and 15uA when closed. I guess the problem was with the wiring. DOn't really know but I used a battery holder instead. I will try to rechange the resistor value to 1Mohm and reupdate.

Edit 27.1.2016: ok I created another node and connected the contact sensor in series with the 1Mohm and the output is the voltage divider. now it is 1.4uA when open and 4.6uA when closed.

Thanks

Yes, i used a 1 Mohm reisitor instead of the internall pull up. You can read this few messages above. This was a tip from GertSander

[Tomasz Pazio]

Hi, I build the board but I still have issues with burning ATMega328p chip.
Can you describe and attach files that should work?
The only success "burn" I had with burning bootloader was with hex and boards entry from first post using arduino uno and ips programer ( so it is like burning uno bootloader with your setup)
After that I was trying to upload sketch but than it was not possible because of "?# in boards file but there is no such sign.
I rewert file to stock and burn sketch like it would be standard uno board but using programer and not standard usb. No idea if it is corect so that is why I ask for more details.
Thank you in advance
Tomasz

[m26872]

@Tomasz-Pazio Sounds more like some issue with the IDE and boards file than hw and fuses/bootloader. Have you tried different IDE versions?

[meddie]

@ahmedadelhosni
what is it on the door? is that a plastic wrap?

[ahmedadelhosni]

@meddie

The sensor is drawn by black rectangle. This is adhesive tape like this : http://2.imimg.com/data2/YX/UQ/MY-3910304/sale-bopp-clarity-adhesive-tape-250x250.jpg

The other red rectangle on the door was old tape I didn't remove. Actually before getting my boards I used a bread board and a battery for testing, so I needed a tape for support and keeping it in place

[meddie]

[Tomasz Pazio]

@m26872 thanks for advice, bootloader burned on IDE 1.0.x and after that, sketches are uploaded properly on 1.6.x.

One more question, how it should report battery state? I can not see any variable created for this in Vera.

[m26872]

@Tomasz-Pazio Great! If I remember Vera correct, a variable should be created automaticly upon first message if you use the sendbatterylevel() fuction.