Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Verisure home alarm status as home/away switch

samppa last edited by
I am trying to get the status of my Verisure alarm system, but the API requires HTTPS login.
The only two workaround methods I have figured out so far are:
1. Monitor the "SmartPlug" that can be configured to turn on or off according to the alarm status
2. Request the alarm status information for the web site with two HTTPS requests
The option 2 would be nice, but I am stuck with the HTTPS requests from Vera3 scene LUUP code.
Not sure if that is even possible. The status page requires first a login HTTPS request and the session tokens to be stored and another HTTPS request to retrieve the actual alarm status.

Any ideas how to implement the HTTPS requests? Do I need to create a "device" and does that provide better access to SSL libraries like LuaSec? Would that help?
Reply Quote 0
1 Reply Last reply

1
Posts

1035
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

1

2
Votes

1
Posts

10
Views

No one has replied
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

1

0
Votes

1
Posts

12
Views

No one has replied
A low cost energy meter
My Project • • OldSurferDude

7

1
Votes

7
Posts

44
Views

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.
Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

5

3
Votes

5
Posts

15
Views

@OldSurferDude thank you !

Verisure home alarm status as home/away switch

Suggested Topics

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

A low cost energy meter
My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Verisure home alarm status as home/away switch

Suggested Topics

Welcome Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino" My Project • • OldSurferDude

A low cost energy meter My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Water Meter or "How to get Home Assistant to send saved data to an Arduino"
My Project • • OldSurferDude

A low cost energy meter
My Project • • OldSurferDude

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts