Meet in Malmö, Summer 2016?

[Anticimex]

I have no clue how I will get "in" or "out" yet. All I know is that I have the wife's blessing. The rest, I figure out as I go :)

[tbowmo]

@Anticimex If you're in Odense I can pick you up on the way over there.

[Anticimex]

@tbowmo Cool! I don't know yet. For sure somewhere between Odense and Bjärred though. But let's keep in touch :)

[sundberg84]

Damn it... I need to reschedule this wife-trip :) "but the other guys got their wifes blessings" haha

[bjacobse]

@tbowmo
Do you drive a car that also could fit me in? I live in Bunkeflostrand (First highway exit as you arrive to Sweden from Øresundsbroen) - as a teaser I will donate a (flak) beers (Ceres Royal English Ale) as a party-starter :-)

[tbowmo]

@bjacobse
It's a Toyota Aygo, but I might find room for you as well (depending on how much gear I will bring though :))

Hmm.. I think I have to start looking for somewhere to stay over there, if we are going for beers all day...

[korttoma]

Safe travels you guys!!

[bjacobse]

Hi all,
Status for participants:
9 good guys (aka Respected Honored Members of MySensors Community)

[Briske]

Hi guys, is the any agenda for this, what should we bring (food, drinks, laptops, DVM, umbrellas etc...) ?
Still waiting for my pcbs to arrive from DirtyPCB..

[mfalkvidd]

@Briske

@hek said:

MYSENORS BBQ MEETING

Where: @hek's garden, Bjärred, SWEDEN
When: 2016-07-09, Is around 10:00 ok?

Bring meat, electronics and beer ;)

Need some control on who's planning on coming so please add your name to doodle.

[bjacobse]

I bring beers

[hek]

Oh, just a week left!

The plan is to have a light lunch ~13. Let me know if you'll arrive later to help me dimension food supply.

And then BBQ dinner ~18:30.

I hope we get decent weather. If it's über hot I'll open the pool, so bring clothes accordingly.

[mfalkvidd]

I hope we get decent weather. If it's über hot I'll open the pool, so bring clothes accordingly.

And water temperature sensors :-)

[bjacobse]

@tbowmo said:

It's a Toyota Aygo, but I might find room for you as well (depending on how much gear I will bring though :))

Thomas regarding the lift - when will you bere here? approx so I can inform HEK the arrival time?

[bjacobse]

I have somehow "bricked" some of my Arduino Pro Mini, I have set fuse to use external oscillator, instead of crystal or internal, so I can't via tinyUSB get them alive again, and need a 12V programmer - someone have this and can bring this along to Malmø meet

[tbowmo]

@bjacobse

I plan to be there at 11ish (give or take a little).

About your programmer issue.. Do you have a oscilloscope at hand? They normally have a 1Khz 5v output that could be used to drive the clock input on your atmega (have done this a couple of times to resurrect a "dead" atmega8)

[mfalkvidd]

Not sure if it helps, but 976.5625Hz is possible to get from PWM on a 16MHz atmega328. Maybe that's close enough to 1kHz?

[tbowmo]

@mfalkvidd

There is no restriction on the clock input (I think it could be as high as 16Mhz) it was just an example of how to get a clock signal for reprogramming the device (and one that I know is working :D )

[bjacobse]

@tboha @mfalkvidd
Thank you guys for this OFF-topic question in this thread... Now my Arduino Pro Mini's are back alive again
I used this code http://forum.arduino.cc/index.php?topic=213053.msg1564631#msg1564631 uploaded into Arduino Duomilanove, used pin9 to touch the ATmega328P in Crystal clkpin1 - and success

On-topic you get first 2 beers on Saturday :-)

[hek]

Meat...

• IKEA variera hack to fit them all in the smoker...