Simple Serial Gateway and sensor does not work...

SGi

I have exactly the same problem.....

LOST

It looks like it's similar to this: https://forum.mysensors.org/topic/4296/unable-to-get-simple-gateway-button-sensor-to-work-together

I'm gonna try the debug for the NRF if it reveals any more...

tekka

@LOST @SGi also make sure GW and node are not too close from each other.

SGi

@tekka my node and gateway are about 1m apart

SGi

Hmmm even when I try the example battery status sketch I get the same results from the debug.... Maybe something to do with the Nano or wiring?

SGi

Oh I am using a Uno for the gateway and a nano for the DHT node...

tekka

@SGi I suggest to put them even further away, I've had similar issues with the LNA PA RF24 version.

SGi

@tekka thanks but that doesn't appear to change anything. Do you understand the error from the sensor debug? Is it not getting a response so it restarts or something? Basically is it more likely the sensor or gateway end with the problem?

? Offline

Here the same, a simple sketch sending a value every 2 seconds on Arduino Pro mini its working but on @scalz simple aa node with atmega328 1MHz bootloader i am getting this error

Starting sensor (RRNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=41)
TSM:FPAR
TSP:MSG:SEND 41-41-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 41-41-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 41-41-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 41-41-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT

And this on the gateway

0;255;3;0;9;TSP:MSG:BC
0;255;3;0;9;TSP:MSG:FPAR REQ (sender=41)
0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL)
0;255;3;0;9;TSP:MSG:GWL OK
0;255;3;0;9;!TSP:MSG:SEND 0-0-41-41 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0
0;255;3;0;9;TSP:MSG:READ 41-41-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSP:MSG:BC
0;255;3;0;9;TSP:MSG:FPAR REQ (sender=41)
0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL)
0;255;3;0;9;TSP:MSG:GWL OK
0;255;3;0;9;!TSP:MSG:SEND 0-0-41-41 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0
0;255;3;0;9;TSP:MSG:READ 41-41-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSP:MSG:BC
0;255;3;0;9;TSP:MSG:FPAR REQ (sender=41)
0;255;3;0;9;TSP:CHKUPL:OK (FLDCTRL)
0;255;3;0;9;TSP:MSG:GWL OK
0;255;3;0;9;!TSP:MSG:SEND 0-0-41-41 s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=fail:0

I am using RFM69 radio

Here is the code link text

scalz

@kenci which aa node? I don't think this is my design ;)

About your issue,I have not digged yet so I don't know. On my side, the stParentUpdate is working I guess as I have not this problem. I'm using RFM69 too with a serial GW. But I'm still on end june temp 2.0b rev so I have not completely migrated to the new lib as I had some sketch to finish. I will update and diffcheck tests device today. So I will see if I fall into this, and try to debug if I can replicate the problem ;)

Just in case, what is your GW? I have serial gw + esp mqtt on my side for testing.

SGi

https://forum.mysensors.org/topic/4316/version-2-0-isn-t-working this could be the fix... Have to try tomorrow night....

? Offline

Sorry @scalz , it was another user who designed the board, user @m26872 was it. My gateway is an ESP8266 with MQTT. I will try to find out what the problem is. With the same sketch it's working on an Arduino Pro 328 3v3. But on @m26872's board with 1MHz it's not.

EDIT:
I found out that my Simple AA node is not receiving packets(ATMega328 1MHZ). So now i have to check why!

EDIT 2:
OK, i found out if i connect DI0 of RFM69 to D2 it's working. But if i want to use D3(because D2 is in use for a switch) it's not working, even if i set #define MY_RF69_IRQ_PIN 3 in my sketch!

scalz

@kenci ok, I think I know where is your problem. Try to add this in your sketch (before mysensors include of course)
#define MY_RF69_IRQ_NUM 1

That should work. I will do the change.

Simple Serial Gateway and sensor does not work...

7

11.7k

11.2k

113.0k