Curtain Control Node.

[AWI]

@Tore-André-Rosander I have defined it as "Blinds Percentage" in Domoticz. This send the V_STATUS and V_PERCENTAGE messages where the node should respond to...

[Tore André Rosander]

@AWI THanks again for your fast replys!

This is what i get in serial monitor when i use the "up" "down" buttons for blinds percentage in domoticz.

This is my very first MySensor setup so it might be some error with my setup, i will have a deeper look at it later tonight.

Starting sensor (RNNNA-, 2.0.0-beta)
Radio init successful.
State read: -1
State read: -1
send: 13-13-0-0 s=255,c=3,t=15,pt=0,l=2,sg=0,st=ok:

send: 13-13-0-0 s=255,c=0,t=17,pt=0,l=10,sg=0,st=ok:2.0.0-beta
send: 13-13-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
read: 0-0-13 s=255,c=3,t=15,pt=0,l=2,sg=0:

read: 0-0-13 s=255,c=3,t=6,pt=0,l=1,sg=0:M
send: 13-13-0-0 s=1,c=0,t=5,pt=0,l=7,sg=0,st=ok:Curtain
send: 13-13-0-0 s=255,c=3,t=11,pt=0,l=18,sg=0,st=ok:Curtain control 13
send: 13-13-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
Init complete, id=13, parent=0, distance=1
read: 0-0-13 s=1,c=1,t=29,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=30,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=29,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=30,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=29,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=30,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=29,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=30,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=29,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized read: 0-0-13 s=1,c=1,t=30,pt=0,l=0,sg=0:
Message - valid: 1, Unrecognized```

[AWI]

@Tore-André-Rosander Nothing wrong with you interpretation. I have not written this sketch as a complete S_COVER implementation. Only the V_PERCENTAGE part (not V_UP/V_DOWN). If you define it in Domoticz as "Blinds percentage" (see my previous post) it will work. Sorry for the confusion.

[Tore André Rosander]

@AWI Seems like my problem is with Domoticz itselfe.
I have the same problem as described in this post https://www.domoticz.com/forum/viewtopic.php?f=6&t=7748

[AWI]

@Tore-André-Rosander You can probably solve it by deleting the sensor in Domoticz and let the sketch present itself as S_DIMMER (and use another sensor id)

[Tore André Rosander]

Maybe its because i have not calibrated it? I dont have any pushbuttons laying around, so im gonna make one with some wires. But i see that there is two pins defined as buttons. Should i use the buttonPin1 as VCC?

So it would look something like buttonPin1 -> buttonPin2 -> button -> gnd?

[AWI]

@Tore-André-Rosander You can ignore buttonpin2. Just connect your "button" to buttonpin1 and ground.

[TheoL]

@AWI I'm curious where you got the rails for the curtain. I wasn't been able to find them, but stumbled on this topic.

[AWI]

@TheoL Ikea :smile:

[TheoL]

@AWI Really interested in the mechanics ;-)

[franzelare]

I'm currently working on a similar project, only I got started with 24V DC motors that I got from my work (left overs from a test project) These motors are very strong (way way over rated) and have a big gearbox what unfortunately makes the movement a bit slow.
I started off with 1 motor to move 2 curtains at the same time, but will change this to 2 motors for either side since the better half of me likes to control the curtains separately in case she only wants to close 1.
Next to the automation there will also be a manual control switch be hidden behind the curtains in case the node is down and I'm not at home to fix the issue...
all running on an ESP8266 (ESP-12e) unit to have it over WiFi and have enough io

Currently the test setup is working fine and I'm ordering parts to start implementing this a bit bigger in the first room. the test setup I made with some old wood 1 meter of rail and a few old rugs as curtains...

I use a GT2 timing belt that is commently used for 3D printers and pully's are widely available as well as the belts in different lengths (I order them on rolls of 10 meters) and attached the timing belt to a carriage that is normally to pull the curtains with a rod.

the motor is mounted on a bracket with currently 2 end stop switches for open and close (but will be 1 switch for open and 1 for close in the final solution)

resulting in driving the curtain from 1 side

electronics are working fine now and need to be ported to a test print and later to a real PCB design

[romeok01]

Hello.

To my project i use stepper motor JK42HS34-0404 and driver L298N.

This is a wiring diagram.

This is a program code that I use

#include <MySensor.h>  
#include <SPI.h>
#include <AccelStepper.h>
#define HALFSTEP 4  // Stepper uses "Halfstep" mode
#define CURTAIN_CLOSED 1000 // value when closed
#define CURTAIN_OPEN 0 // value when open
#define CHILD_ID 1   // Id of the sensor child
// MySensors definitions
MySensor gw;
// Initialize message
MyMessage msg(CHILD_ID, V_TRIPPED);


// Motor pin definitions
#define motorPin1  3     // IN1 on the ULN2003 driver 1
#define motorPin2  4     // IN2 on the ULN2003 driver 1
#define motorPin3  5     // IN3 on the ULN2003 driver 1
#define motorPin4  6     // IN4 on the ULN2003 driver 1

// Initialize with pin sequence IN1-IN3-IN2-IN4 for using the AccelStepper with 28BYJ-48
AccelStepper stepper1(HALFSTEP, motorPin1, motorPin2, motorPin3, motorPin4);

unsigned long current_position ; // remembers current position, need to be saved in EEPROM?

void setup() {
  // MySensors
  gw.begin(); // fixed node 13
  gw.sendSketchInfo("Curtain control 13", "1.0"); // Send the sketch version information to the gateway and Controller

  //pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
  
  stepper1.setMaxSpeed(500.0);
  stepper1.setAcceleration(700.0);
  stepper1.moveTo(CURTAIN_OPEN);
  
  current_position = CURTAIN_OPEN ;
  stepper1.moveTo(CURTAIN_OPEN);
}//--(end setup )---

void loop() {
  // if message = V_UP start moving until closed
  // if message = V_DOWN start moving back until open
  // if message = V_STOP stop moving
  // Test: Change direction when the stepper reaches the target position
  gw.process(); // check if message from controller
  if (stepper1.distanceToGo() == 0){
    if (stepper1.currentPosition() == CURTAIN_OPEN){
      stepper1.moveTo(CURTAIN_CLOSED);
      Serial.println("Curtain Open, now closing");
      gw.request(CHILD_ID, V_UP, 0); // request new values from controller  
    }
    else{
      stepper1.moveTo(CURTAIN_OPEN);
      Serial.println("Curtain Closed, now opening");
      gw.request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
  }
  
  stepper1.run();
}

// This is called when a message is received 
void incomingMessage(const MyMessage &message) {
  // We only expect few types of messages from controller, check which
  stepper1.moveTo(message.getInt() * CURTAIN_CLOSED/100);
  Serial.print("Message - valid: ");
  Serial.print(message.sensor);
  Serial.print(" , value: % ");
  Serial.println(message.getInt());
  switch (message.getInt()) {
  case 100:
    // Curtain should be opened
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message UP ");
     stepper1.moveTo(CURTAIN_OPEN);
     break;
  case 0:
    // Curtain should be closed
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message DOWN ");
     stepper1.moveTo(CURTAIN_CLOSED);
    break;
  case 50:
    // Curtain action should be stopped
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Message STOP ");
    break;
  default: 
    // not recognizable message
     Serial.print("Message - valid: ");
     Serial.print(message.sensor);
     Serial.print(", Unrecognized ");

  }
 
}

When the program I have uploaded to my mysensors, the engine still turns, one left and one to the right and did not work the button blinds in Domoticz.

I cant turn off my stepper motor in Domoticz.

https://www.youtube.com/embed/1Wc1p_9YDQQ

Please help me.

[romeok01]

I write a program on library Stepper not AccelStepper.
Now is working.

Program code:

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <Stepper.h>

#define CURTAIN_CLOSED 1000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN -1000         // wartosc gdy kurtyna otwarta 
#define CHILD_ID 1

// definicje MySensors 

MyMessage message(CHILD_ID, S_COVER);

int in1Pin = 3;
int in2Pin = 4;
int in3Pin = 5;
int in4Pin = 6;
int lastState;
 
// liczba kroków na jeden obrót
#define stepsPerRevolution 200

//ustawienie szybkości silnika 
int motorSpeed = 40;

Stepper myStepper(stepsPerRevolution, in1Pin, in2Pin, in3Pin, in4Pin);

void setup() {
  
// ustawienie pinów jako wyjście
  pinMode(in1Pin, OUTPUT);
  pinMode(in2Pin, OUTPUT);
  pinMode(in3Pin, OUTPUT);
  pinMode(in4Pin, OUTPUT);
// ustawienie szybkosci silnika
  myStepper.setSpeed(motorSpeed);
}

void presentation()  
{ 
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Program kurtyna", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void receive(const MyMessage &message) {
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     myStepper.step(CURTAIN_OPEN);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
        }
     
 if (message.type==V_DOWN) {
     myStepper.step(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_DOWN, 0); // request new values from controller
        } 
}

I use MySensors Library 2.0

Youtube film

https://www.youtube.com/embed/gm0r2kDXrt4

[franzelare]

your wiring diagram is not accessable:
Error (403)
It seems you don't belong here! You should probably sign in. Check out our Help Center and forums for help, or head back to home.

i use a DC motor so can't help with stepper motors, but can you share an image of how you setup your rails?

[romeok01]

Now the wiring diagram should be visible.

[romeok01]

I write program with AccelStepper library

/ Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <AccelStepper.h>      //import biblioteki AccelStepper 

#define HALFSTEP 8
#define CURTAIN_CLOSED 2000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN 0       // wartosc gdy kurtyna otwarta
#define CHILD_ID 1

// definicje MySensors

MyMessage message(CHILD_ID, S_COVER);

// Definicja pinow silnika
#define IN1  3     // IN1 - zielony
#define IN2  4     // IN2 - czarny
#define IN3  5     // IN3 - niebieski
#define IN4  6     // IN4 - czerwony
 
AccelStepper stepper1(HALFSTEP, IN1, IN2, IN3, IN4);

void setup()
{
  stepper1.setMaxSpeed(200.0);
  stepper1.setAcceleration(1000.0);
  stepper1.setSpeed(200);
  stepper1.moveTo(CURTAIN_OPEN);
}

void presentation() 
{
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Program kurtyna", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void loop()
{
  stepper1.run();  //Start
}

void receive(const MyMessage &message)
{
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     if (stepper1.distanceToGo() == 0){
         if (stepper1.currentPosition() == CURTAIN_OPEN){
             stepper1.moveTo(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
         }
      }
   }
   if (message.type==V_DOWN) {
       stepper1.moveTo(CURTAIN_OPEN);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
    if (message.type==V_STOP) {
        stepper1.setCurrentPosition(0);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        request(CHILD_ID, V_STOP, 0); // request new values from controller
    }
}

I use MySensors library 2.0

Now i working.

[jacikaas]

Hello,

I trying to adopt the code for 28BYJ-48 stepper motor with ULN2003 driver board for roller blinds control. Code is working, but when the stepper motor is always on - it gets hot. Because of it also its consumes more energy. So thats why I want to turn on ULN2003 board only when new action is started, and after that it should be shuted down again. I could do it, because ULN2003 has On/Off jumper:

Question #1: I trying to use relay for that On/Off. Could I do it without relay and control On/Off jumper directly from arduino? Does relay is the best solution?

Question #2: I suck at programming, but I trying to add theese lines to my code to control the relay SIL05-1A72-71D, which controls the ULN2003 driver board:
int powerPin = 7; //before SETUP
pinMode(powerPin, OUTPUT); // In SETUP
digitalWrite(powerPin, LOW); // In SETUP
digitalWrite(powerPin, HIGH); // In void receive function
delay(CURTAIN_CLOSED); // In void receive function
digitalWrite(powerPin, LOW); // In void receive function

digitalWrite(powerPin, HIGH); - I think is in right position, but I don't know how to turn off relay when action is done. Please advise for coding, because I not good in it. Thank You! Below is the code:

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_NODE_ID 10
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
//#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <AccelStepper.h>      //import biblioteki AccelStepper 

#define HALFSTEP 8
#define CURTAIN_CLOSED 10000  // wartosc gdy kurtyna zamknieta
#define CURTAIN_OPEN 0       // wartosc gdy kurtyna otwarta
#define CHILD_ID 1

int powerPin = 7;

// definicje MySensors

MyMessage message(CHILD_ID, S_COVER);

// Definicja pinow silnika
#define IN1  3     // IN1 - zielony
#define IN2  4     // IN2 - czarny
#define IN3  5     // IN3 - niebieski
#define IN4  6     // IN4 - czerwony
 
AccelStepper stepper1(HALFSTEP, IN1, IN3, IN2, IN4);

void setup()
{
  stepper1.setMaxSpeed(1000.0);
  stepper1.setAcceleration(100.0);
  stepper1.setSpeed(200);
  stepper1.moveTo(CURTAIN_OPEN);
  
  pinMode(powerPin, OUTPUT);
  digitalWrite(powerPin, LOW);
}

void presentation() 
{
  // Wyslanie informacji o wersji programu
  sendSketchInfo("Roller blinds", "1.0");
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER); // Window Cover sub-type, commands: V_UP, V_DOWN, V_STOP
}

void loop()
{
  stepper1.run();  //Start
}

void receive(const MyMessage &message)
{
  // if message = V_UP start moving until closed
  if (message.type==V_UP) {
     digitalWrite(powerPin, HIGH);
     if (stepper1.distanceToGo() == 0){
         if (stepper1.currentPosition() == CURTAIN_OPEN){
             stepper1.moveTo(CURTAIN_CLOSED);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     request(CHILD_ID, V_UP, 0); // request new values from controller
         }
      }
   }
   if (message.type==V_DOWN) {
       digitalWrite(powerPin, HIGH);
       stepper1.moveTo(CURTAIN_OPEN);
       // Store state in eeprom
       saveState(message.sensor, message.getBool());
       request(CHILD_ID, V_DOWN, 0); // request new values from controller   
    }
    if (message.type==V_STOP) {
        digitalWrite(powerPin, HIGH);
        stepper1.setCurrentPosition(0);
        // Store state in eeprom
        saveState(message.sensor, message.getBool());
        request(CHILD_ID, V_STOP, 0); // request new values from controller
    }
 //   delay(CURTAIN_CLOSED);
 //   digitalWrite(powerPin, LOW);
}

[Suresh Mali]

@jacikaas said in Curtain Control Node.:

void receive(const MyMessage &message)
{
// if message = V_UP start moving until closed
if (message.type==V_UP) {
digitalWrite(powerPin, HIGH);
if (stepper1.distanceToGo() == 0){
if (stepper1.currentPosition() == CURTAIN_OPEN){
stepper1.moveTo(CURTAIN_CLOSED);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_UP, 0); // request new values from controller
}
}
}
if (message.type==V_DOWN) {
digitalWrite(powerPin, HIGH);
stepper1.moveTo(CURTAIN_OPEN);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_DOWN, 0); // request new values from controller
}
if (message.type==V_STOP) {
digitalWrite(powerPin, HIGH);
stepper1.setCurrentPosition(0);
// Store state in eeprom
saveState(message.sensor, message.getBool());
request(CHILD_ID, V_STOP, 0); // request new values from controller
}
// delay(CURTAIN_CLOSED);
// digitalWrite(powerPin, LOW);
}

You can enable and disable outputs and try. In the following function:

void receive(const MyMessage &message)

//add the following at the begining of the function
stepper1.enableOutputs ()
//and add the following at the end in the same function.
stepper1.disableOutputs ()

I hope this helps haven't tried it myself.

[jacikaas]

@suresh-mali Thank You Suresh for Your answer!
I disconnect relay and delete it lines from the code.

I add lines to code like You said:

void receive(const MyMessage &message)
{
stepper1.enableOutputs ();
 // rest of code
stepper1.disableOutputs ();
}

It looks like it have to work because it is simple solution, but it doesn't... On driver board ULN2003, when motor is not rotating, A Led is always on. I think if command with disableOutputs would be activated, then the LED should not be on?

[Suresh Mali]

@jacikaas Ok.

//Remove this line from loop function
stepper1.run(); 

//Change this line
stepper1.moveTo(CURTAIN_CLOSED);
//to
stepper1.runToPosition(CURTAIN_CLOSED);

I hope this works. Also make similar changes in block which closes curtains.
Refernce article: https://www.pjrc.com/teensy/td_libs_AccelStepper.html