rboard - Cheap relay/radio/arduino board ~$10
-
Yeah it seems like a really nice board but it could have had access to a few more digital pins on the board.
Is it really only A0 and D3 that can be accessed other then the relay? -
Yeah it seems like a really nice board but it could have had access to a few more digital pins on the board.
Is it really only A0 and D3 that can be accessed other then the relay?@korttoma said:
Yeah it seems like a really nice board but it could have had access to a few more digital pins on the board.
Is it really only A0 and D3 that can be accessed other then the relay?Looks like. Surprising that folks don't at least put a few more pins on solderable holes on boards like this, where you could put a pin or solder a wire - seems easy and takes little space.
-
-
@Homer said:
Which board do I choose when uploading a sketch to this?
It's all good, I found a website which stated what it was compatible with So I'm moving on :-)
Now I am just trying to work out how to connect a switch to the A0 pin. There are two pins so is the switch just bridging the two? Sorry, I really am trying to learn this stuff.
-
Ok, looks like I am slowly getting there :-)
fyi I tried playing around with the above sketch, but it's a no go as Codebender tells me <Bounce2.h> is missing.
-
The link above has been updated to point the MySensors codebender location (where Bounce2 is available).
-
I used one of these boards for a multi sensor recently.... Temp/Motion and Relay actuator.
Turns out to be a very tidy solution !
I'm using the A0 pins connected to a ds18b20 . This is really cute in that the sensor is connected in parasite mode meaning i only need two wires. To do this all you need to do is join pin 1 and 3 to GND and the middle signal wire goes to the A0 ( which is used as D14 ). The rboard also has a 10k resistor from the A0 connection to 3.3v. It works just fine!!
Then for the PIR, im using the readily available RF433 connections to provide D3, 3.3v and GND. The cute trick here is that even though these PIR's are designed for 5v, they run great on 3,3 v too...you just need to connect it differently! See in the photo where the yellow wire which is the 3.3 v vcc supply connects on the PIR sensor.. Genius!!!
See here for background on this:
http://techgurka.blogspot.com.au/2013/05/cheap-pyroelectric-infrared-pir-motion.htmlDo this, feed it 5v ( as relay needs 5v) and you have a tidy little multisensor.
Here's some pics:
full sketch here https://codebender.cc/sketch:61919
-
@gregl I've now my rboard, but I have no Foca, so I used my programmer I matched against the pins on the board.
I choose mini pro 3V3 in the arduino ide but impossible to sync .... is there something I am missing ?
Also, do you change something on initialization as for the 4 switch version ?
thanks,
-
Hi @epierre - I do have a foca and i program as Nano with Atmega328.
What do you mean "change something on initialization as for the 4 switch version" ?? iirc i also just programmed that as a Nano. is this what you mean??
Cheers,
Greg -
@epierre - you dont need the foca programmer... any programmer should work as long as you wire correctly - you could even use another arduino.
http://www.instructables.com/id/Arduino-Examples-2-Use-an-Arduino-as-a-FTDI-Progr/- make sure you only feed it 3.3v via the programming socket...!
For the 4 relay board the CE/CS pins are wired differently to the defaults used by MySensors sketches (9,10) , so you need to tell mysensors library to use (8,9) as this is how they are wired on the Rboard - see the doco ftp://imall.iteadstudio.com/IM120618001_RBoard/DS_IM120618001_RBoard.pdf
-
@epierre - you dont need the foca programmer... any programmer should work as long as you wire correctly - you could even use another arduino.
http://www.instructables.com/id/Arduino-Examples-2-Use-an-Arduino-as-a-FTDI-Progr/- make sure you only feed it 3.3v via the programming socket...!
For the 4 relay board the CE/CS pins are wired differently to the defaults used by MySensors sketches (9,10) , so you need to tell mysensors library to use (8,9) as this is how they are wired on the Rboard - see the doco ftp://imall.iteadstudio.com/IM120618001_RBoard/DS_IM120618001_RBoard.pdf
@gregl nope, I tried and it failed... this is why I asked. One pin is missing, another has another use... I've ordered the foca and I will see.
Regarding your PIR Wiring on the picture, you added a 1DS80 right ? I mistakenly thought it was the yellow one ...
