Multisensor PIR and Lux

[kchest]

I was finally able to combine the two example sketches (BH1750 Lux sensor and the HC-SR501. I thought I would share it in case it might help out another newbie like me

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 *Light/Motion sensor using sketches from idefix and Henrik Ekblad
 * 
 * DESCRIPTION
 * Arduino BH1750FVI Light sensor
 * communicate using I2C Protocol
 * this library enable 2 slave device addresses
 * Main address  0x23
 * secondary address 0x5C
 * connect the sensor as follows :
 *
 *   VCC  >>> 5V
 *   Gnd  >>> Gnd
 *   ADDR >>> NC or GND  
 *   SCL  >>> A5
 *   SDA  >>> A4
 * http://www.mysensors.org/build/light
 * Motion Sensor example using HC-SR501 
 * http://www.mysensors.org/build/motion
 */


// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensors.h>  
#include <BH1750.h>
#include <Wire.h>

#define CHILD_ID_LIGHT 0
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define CHILD_ID_Motion 1   // Id of the sensor child
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)

BH1750 lightSensor;

// V_LIGHT_LEVEL should only be used for uncalibrated light level 0-100%.
// If your controller supports the new V_LEVEL variable, use this instead for
// transmitting LUX light level.
MyMessage msgLight(CHILD_ID_LIGHT, V_LEVEL);
// Initialize motion message:
MyMessage msgMotion(CHILD_ID_Motion, V_TRIPPED);

uint16_t lastlux;

void setup()  
{ 
  lightSensor.begin();
  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Lux/Motion Sensor", "1.0");

  // Register all sensors to gateway (they will be created as child devices)
  present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
  present(CHILD_ID_Motion, S_MOTION);
}

void loop()      
{     
  uint16_t lux = lightSensor.readLightLevel();// Get Lux value
  Serial.println(lux);
  if (lux != lastlux) {
      send(msgLight.set(lux));
      lastlux = lux;
  }
  
 // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
        
  Serial.println(tripped);
  send(msgMotion.set(tripped?"1":"0"));  // Send tripped value to gw 

  // Sleep until interrupt comes in on motion sensor. Send update every two minute.
  sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
}

[tomrask]

Hey Kcest

Nice work!
Can you help me if I would like two PIR sensors in the same sketches.

thank you in advance, Tom