Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

NRF24L01 and rfm69 in one gateway

Omemanti last edited by

Hey There,

Now I got multiple sensors using a NRF24L01. I'm of to a new journey, the rfm69.

Is there a way to combine bothe radios in one gateway?
I use an esp8266(node-UMC) with NRF24L01. Haven't got a spare esp lying around..

Thnx!
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by @Omemanti

@Omemanti sorry, only one transport type per gateway is supported.

Maybe you have a spare Arduino to create a serial gateway?

In either case I would recommend ordering a few esp. I use the wemos d1 mini version. Cheap and easy to use
Reply Quote 0
1 Reply Last reply
Omemanti last edited by @mfalkvidd

@mfalkvidd oké, clear!
Unfortunate.
Guess a couple esp8266 couldn't hurt.
Reply Quote 1
1 Reply Last reply

gateway 101 nrf24 15 rfm69hw 12

3
Posts

1593
Views

Log in to reply

Suggested Topics

Pi 4 ethernet gateway with NRF24L01 + PA and LNA & Domoticz
My Project • gateway • • bsmtdweller

17

0
Votes

17
Posts

93
Views

Cool project @bsmtdweller New thread or stay in this doesn't matter much, but for people searching the forum (or their favorite search engine) in the future, I think a new thread with a subject containing "incubator" will be more clear. I would build it with multiple nodes. Smaller chunks of code, easier wiring, easier to isolate individual parts which helps tremendously when troubleshooting, easer to reuse code for one node in case you (or someone else) want to expand the project later, easier to remove a part if you (or someone else) don't need it. The non-mysensors code is more important, so I would start with that, but make sure all parameters that you want to be able to change are stored in variables and not hardcoded. Then add the MySensors code to update the values of the variables. The autonomy will be hard. Normally I would prefer to have all logic in the controller, since a controller has much better ways to program and debug stuff. Not fun to write - and maintain - in C with very rudamentary debugging tools. But as you say, being reliant on having Domoticz working all the time might not be good. Having the system fail gracefully will be a challenge. A start could be to search the forum for MY_TRANSPORT_WAIT_READY_MS to see what others have done. And maybe - to make the system as reliable as possible - you should add everything to a single node instead of splitting it up into multiple nodes.
Will serial gateway work with 3.3 V Arduino Pro Mini?
Troubleshooting • gateway rfm69 pro mini • • Thomas433

5

0
Votes

5
Posts

59
Views

@TheoL Thanks for responding and sorry for my late reply. I finally got an Arduino Nano working as a gateway with RFM69. It required new/different logic converters as the ones I had apparently were not working correctly. I can give the RFM69 3.3V power from the Nano, but as the Nano has 5V logic and the RFM69 cannot handle 5V logic as input (NSS, SCK, MOSI) , the logic converters are needed to protect the RFM69 module as also stated in the MySensors radio guide. I must say that using NRF24 was much easier than using RFM69, but I will stick with RFM69 (433 MHz) for range reasons.
heartbeat? monitor?
Development • gateway raspberry monitoring • • CrankyCoder

3

0
Votes

3
Posts

1134
Views

any idea how often heartbeat messages would be sent?
Cross compile mysensors gateway
General Discussion • gateway raspberry pi • • Jasper van Zuijlen

6

0
Votes

6
Posts

88
Views

As promised, what I found so far: the following dockerfile yeilds a usable cross-compile environment, provided you use it with a Makefile. FROM ubuntu:xenial RUN apt-get update \ && apt-get install --yes \ vim \ build-essential \ git RUN git clone https://github.com/raspberrypi/tools RUN git clone https://gist.github.com/3873805.git /build WORKDIR "/build" CMD ["/usr/bin/make", "CC=/tools/arm-bcm2708/gcc-linaro-arm-linux-gnueabihf-raspbian-x64/bin/arm-linux-gnueabihf-gcc" , "HelloWorld"] # Seems I need a real makefile for the above to work. For cross compiling mysensors to work, hoever, you also need to properly seed the variable in configure, for it to work correctly. This is where I left off. Sources: https://stackoverflow.com/questions/18007326/how-to-change-default-values-of-variables-like-cc-in-makefile https://bitbucket.org/mitchallen/pi-hello-cross-compile/src/master/ https://desertbot.io/blog/how-to-cross-compile-for-raspberry-pi https://github.com/mitchallen/pi-cross-compile/blob/master/Dockerfile https://github.com/mysensors/MySensors/blob/development/configure https://github.com/raspberrypi/tools/tree/master/arm-bcm2708/arm-bcm2708-linux-gnueabi/bin https://www.raspberrypi.org/documentation/linux/kernel/building.md https://www.mysensors.org/build/raspberry
Help Finding Problem
Troubleshooting • gateway mqtt nrf24 node error • • Soloam

6

0
Votes

6
Posts

1077
Views

Just one final question... is the approach to MQTT correct or should I stick with simple Ethernet? I was planning on using OpenHab or Home Assistant. Thank You all
💬 MySWeMosGWShield - WeMos Mini MySensors Gateway Shield
OpenHardware.io • mysensors gateway nrf24l01 rfm69 esp8266 contest2017 wemos • • openhardware.io

40

0
Votes

40
Posts

10594
Views

What are the parameters of this radio, I could not get it to work. Suspicions that he had no speed 250.
all the gear, no idea
General Discussion • gateway vera help newbie • • baldsi

10

0
Votes

10
Posts

4663
Views

@maltimus - thanks, I can see the picture. frstratingly I have the Vera Edge though!
Step-by-step procedure to connect the NRF24L01+ to the GPIO pins and use the Raspberry as a Serial Gateway (MySensors 1.x)
Hardware • gateway raspberry pi raspberry nrf24 raspberry nrf24l01 gpio • • mfalkvidd

168

14
Votes

168
Posts

174981
Views

@ricorico94 welcome to the MySensors commu ity! All you need to do when switching from raspberry pi gateway to ethernet gateway is change the "hardware" configuration in Domoticz. However, if you are just starting out, don't use this gateway. It works for MySensors 1.x only. Use the new raspberry pi gateway instead.

24
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1