6/8 Buttons battery remote node

gohan

@neverdie this is the one I'm talking about http://www.circuitstoday.com/interfacing-hex-keypad-to-arduino

wes

I have the same use case (remote control with buttons to control lights/scenes).

I'm planning to use some cheap RF remotes and connect a RF receiver to my RPI, which hosts both my gateway and controller.

Not sure if I'll receive the codes via MySensors, or write something that talks directly to the controller (thoughts on pros/cons of each approach welcome).

Of course this won't be as reliable or flexible as buttons connected to a MySensors node, but it should be enough for my needs.

Further thoughts welcome :-)

Nca78

@wes said in 6/8 Buttons battery remote node:

I have the same use case (remote control with buttons to control lights/scenes).

I'm planning to use some cheap RF remotes and connect a RF receiver to my RPI, which hosts both my gateway and controller.

Not sure if I'll receive the codes via MySensors, or write something that talks directly to the controller (thoughts on pros/cons of each approach welcome).

Of course this won't be as reliable or flexible as buttons connected to a MySensors node, but it should be enough for my needs.

Further thoughts welcome :-)

I think you should change the remote controls into MySensors nodes. A bit more work at the beginning but you'll probably save a lot of hair pulling, reliability etc in the long term.

Carywin

You can use pin change interrupts with MySensors sleep loops with an easy hack. Here's the code I use for 4 button battery powered nodes that also report temperature and humidity using DHT a sensor. I run them from 2 AA and so far they've been running for more than 6 months without showing signs of discharge. This could be easily modified for 6 or 8 buttons.

// MySensors EnviroButtons
// Temperature and Humidity Sensor with 4 Push Buttons
// Battery Powered Node
// Don't forget to change buttons and VCC_CAL for each node

// Cary Wintle - July 2017

// MySensors configuration
// -----------------------
#define SN "EnviroButtons"  // Software name
#define SV "0.4"            // Version number
//#define MY_DEBUG
#define MY_NODE_ID 6
#define MY_RADIO_RFM69
#define MY_RFM69_NETWORKID 137
#define MY_RFM69_ENABLE_ENCRYPTION
#define MY_RFM69_NEW_DRIVER
#define MY_RFM69_FREQUENCY RFM69_433MHZ
#define MY_IS_RFM69HW
#include <MySensors.h>

#include <SPI.h>
#include <DHT.h>

#define EI_NOTEXTERNAL // External interrupts managed by built-in routines
#include <EnableInterrupt.h> // Pin-change interrupts

// Set this to the pin you connected the DHT's data pin to
#define DHT_DATA_PIN 8

// Buttons
#define BUTTON1_PIN A1 // 5: A1 - 6: A1
#define BUTTON2_PIN A2 // 5: A3 - 6: A2
#define BUTTON3_PIN A3 // 5: A2 - 6: A3
#define BUTTON4_PIN A0 // 5: A0 - 6: A0

// Set this offset if the sensor has a permanent small offset to the real temperatures
#define SENSOR_TEMP_OFFSET 0

// Sleep time between sensor updates (in milliseconds)
// Must be >1000ms for DHT22 and >2000ms for DHT11
static const uint64_t UPDATE_INTERVAL = 120000;
#define BAT_UPDATE_INTERVAL 720 // 24 hrs - Interval between battery updates (multiples of UPDATE_INTERVAL)
// VCC Calibration Values
// Node 5: 1128953L
// Node 6: 1125300L
#define VCC_CAL 1125300L

// Force sending an update of the temperature after n sensor reads, so a controller showing the
// timestamp of the last update doesn't show something like 3 hours in the unlikely case, that
// the value didn't change since;
// i.e. the sensor would force sending an update every UPDATE_INTERVAL*FORCE_UPDATE_N_READS [ms]
static const uint8_t FORCE_UPDATE_N_READS = 30; // After an hour

float lastTemp;
float lastHum;
uint8_t nNoUpdatesTemp;
uint8_t nNoUpdatesHum;
int cycleCount = BAT_UPDATE_INTERVAL; // Send battery update immediately
volatile byte B1Int = 0, B2Int = 0, B3Int = 0, B4Int = 0; // Interrupt button flags
uint32_t now;

MyMessage msgHum(0, V_HUM);
MyMessage msgTemp(0, V_TEMP);
MyMessage msgButtons(0, V_SCENE_ON);
MyMessage msgBattV(0, V_VOLTAGE);
DHT dht;

void presentation()  
{ 
  // Send the sketch version information to the gateway
  sendSketchInfo(SN,SV);
  // Present the sensor
  present(0, S_CUSTOM, "Temp/Humid/Buttons");
}

void setup()
{
  // Setup pins the DHT sensor is on
  digitalWrite(6, LOW);
  pinMode(6, OUTPUT);
  digitalWrite(7, LOW);
  pinMode(7, OUTPUT);
  digitalWrite(9, HIGH);
  pinMode(9, OUTPUT);

  sleep(2000);

  dht.setup(DHT_DATA_PIN); // Setup the DHT sensor

  pinMode(BUTTON1_PIN,INPUT_PULLUP);
  pinMode(BUTTON2_PIN,INPUT_PULLUP);
  pinMode(BUTTON3_PIN,INPUT_PULLUP);
  pinMode(BUTTON4_PIN,INPUT_PULLUP);
  enableInterrupt(BUTTON1_PIN,Button1,FALLING);
  enableInterrupt(BUTTON2_PIN,Button2,FALLING);
  enableInterrupt(BUTTON3_PIN,Button3,FALLING);
  enableInterrupt(BUTTON4_PIN,Button4,FALLING);
}

void Button1() {
  B1Int++;
  _wokeUpByInterrupt = 0xFE; // Dirty hack to get out of MySensors sleep loop
}

void Button2() {
  B2Int++;
  _wokeUpByInterrupt = 0xFE; // Dirty hack to get out of MySensors sleep loop
}

void Button3() {
  B3Int++;
  _wokeUpByInterrupt = 0xFE; // Dirty hack to get out of MySensors sleep loop
}

void Button4() {
  B4Int++;
  _wokeUpByInterrupt = 0xFE; // Dirty hack to get out of MySensors sleep loop
}


void loop() {
  _wokeUpByInterrupt = INVALID_INTERRUPT_NUM;
  // Power up the DHT sensor
  digitalWrite(9, HIGH);

  // Process buttons
  if(B1Int > 0) {
    send(msgButtons.set(1));
    B1Int = 0;
  } else if(B2Int > 0) {
    send(msgButtons.set(2));
    B2Int = 0;
  } else if(B3Int > 0) {
    send(msgButtons.set(3));
    B3Int = 0;
  } else if(B4Int > 0) {
    send(msgButtons.set(4));
    B4Int = 0;
  }

  // Wait for the DHT sensor to init
  sleep(2000);
  
  // Force reading sensor, so it works also after sleep()
  dht.readSensor(true);
  
  // Get temperature from DHT library
  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
    Serial.println("Failed reading temperature from DHT!");
  } else if (temperature != lastTemp || nNoUpdatesTemp == FORCE_UPDATE_N_READS) {
    // Only send temperature if it changed since the last measurement or if we didn't send an update for n times
    lastTemp = temperature;
    // Reset no updates counter
    nNoUpdatesTemp = 0;
    temperature += SENSOR_TEMP_OFFSET;
    send(msgTemp.set(temperature, 1));

    #ifdef MY_DEBUG
    Serial.print("T: ");
    Serial.println(temperature);
    #endif
  } else {
    // Increase no update counter if the temperature stayed the same
    nNoUpdatesTemp++;
  }

  // Get humidity from DHT library
  byte humidity = (byte)dht.getHumidity();
  if (humidity != lastHum || nNoUpdatesHum == FORCE_UPDATE_N_READS) {
    // Only send humidity if it changed since the last measurement or if we didn't send an update for n times
    lastHum = humidity;
    // Reset no updates counter
    nNoUpdatesHum = 0;
    send(msgHum.set(humidity, 1));
    
    #ifdef MY_DEBUG
    Serial.print("H: ");
    Serial.println(humidity);
    #endif
  } else {
    // Increase no update counter if the humidity stayed the same
    nNoUpdatesHum++;
  }

  if (cycleCount >= BAT_UPDATE_INTERVAL) {
    cycleCount = 0;
    int BatV = readVCC();
    #ifdef MY_DEBUG
    Serial.print("BatVR: ");
    Serial.println(BatV);
    #endif
    float BatVolts = BatV / 1000.0;
    #ifdef MY_DEBUG
    Serial.print("BatV: ");
    Serial.println(BatVolts);
    #endif
    send(msgBattV.set(BatVolts, 2));
    float BatPercent = (BatVolts - 2.8) / 0.6 * 100;
    if(BatPercent > 100) BatPercent = 100;
    #ifdef MY_DEBUG
    Serial.print("Bat%: ");
    Serial.println(BatPercent);
    #endif
    sendBatteryLevel((int)BatPercent);
  }
  cycleCount++;

  // Power down the DHT sensor
  digitalWrite(9, LOW);
  
  // Sleep for a while to save energy
  sleep(UPDATE_INTERVAL); 
}

int readVCC() {
  // Read 1.1V reference against AVcc
  // set the reference to Vcc and the measurement to the internal 1.1V reference
    ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);

  wait(2); // Wait for Vref to settle
  ADCSRA |= _BV(ADSC); // Start conversion
  while (bit_is_set(ADCSRA,ADSC)); // measuring

  uint8_t low  = ADCL; // must read ADCL first - it then locks ADCH  
  uint8_t high = ADCH; // unlocks both

  int result = (high<<8) | low;

  #ifdef MY_DEBUG
  Serial.print("R: ");
  Serial.println(result);
  #endif

  result = VCC_CAL / result; // Calculate Vcc (in mV); 1125300 = 1.1*1023*1000
  return result; // Vcc in millivolts
}

dbemowsk

@carywin Certain arduinos such as the pro minis can ONLY do interrupts on pins 2 or 3 from my understanding.

gohan

@carywin what is the sleep current of your node with this "interrupt hack"?

NeverDie

Here's the PCB I made for the matrix keypad:

The whole thing fits on a single sided PCB. :)

NeverDie

@dbemowsk said in 6/8 Buttons battery remote node:

@carywin Certain arduinos such as the pro minis can ONLY do interrupts on pins 2 or 3 from my understanding.

IIRC, you can do interrupts from other pins too, but each is tied to a separate bank of pins, so you have to do additional testing to determine which specific pin triggered the interrupt. In the case of the voltage divider keypad, that should be no problem.

NeverDie

Here's the link: https://playground.arduino.cc/Main/PinChangeInterrupt

So, in this scenario, it would be:
ISR (PCINT1_vect) pin change interrupt for A0 to A5

NeverDie

Here's a revision of the earlier code so that it uses ONLY ONE PIN (namely, A0) on the Arduino. And yes, this does work on a pro mini too, because that's what I tested it on. :)

//  Description:
//  Use just A0 to process the 12 button keypad.  
//  Button press is detected by interrupt set on A0.
//  Which button was pressed is determined by an analog read of A0.

// Note: sleep code borrows from Nick Gammon's Schedule J
// Interrupt code borrows from https://playground.arduino.cc/Main/PinChangeInterrupt

#include <avr/sleep.h>

void pciSetup(byte pin)
{
    *digitalPinToPCMSK(pin) |= bit (digitalPinToPCMSKbit(pin));  // enable pin
    PCIFR  |= bit (digitalPinToPCICRbit(pin)); // clear any outstanding interrupt
    PCICR  |= bit (digitalPinToPCICRbit(pin)); // enable interrupt for the group
}

ISR (PCINT1_vect) // handle pin change interrupt for A0 to A5 here
 {
     //no need to do anything beyond just waking up.
 }  

void setup() {
  pinMode(A0,INPUT);
  pciSetup(A0);
  Serial.begin(115200);
  Serial.println("Starting...");
  Serial.flush();
}

void loop() {
  uint16_t voltage;

  set_sleep_mode (SLEEP_MODE_PWR_DOWN);  
  sleep_enable();

  // Do not interrupt before we go to sleep, or the
  // ISR will detach interrupts and we won't wake.
  noInterrupts ();
  
  pciSetup(A0);
  
  // turn off brown-out enable in software
  // BODS must be set to one and BODSE must be set to zero within four clock cycles
  MCUCR = bit (BODS) | bit (BODSE);
  // The BODS bit is automatically cleared after three clock cycles
  MCUCR = bit (BODS); 
  
  // We are guaranteed that the sleep_cpu call will be done
  // as the processor executes the next instruction after
  // interrupts are turned on.
  interrupts ();  // one cycle
  sleep_cpu ();   // one cycle

  delay(20);  //debounce the button
  voltage=analogRead(A0);  //throw out this first result
  voltage=analogRead(A0);
  if (voltage>700) {
    Serial.println(voltage);
    Serial.flush();
  }
}

gohan

How does that integrates with mysensors?

NeverDie

@gohan That's your department. :)

gohan

@neverdie well... kind of... I haven't written mysensors' core so I don't know if it will clash with normal sleep management.

NeverDie

Here's an improved sketch that gives you the number (rather than the voltage) of the button that was pressed:

//  Description:
//  Use just A0 to process the 12 button keypad.  
//  Button press is detected by interrupt set on A0.
//  Which button was pressed is determined by an analog read of A0.

// Note: sleep code borrows from Nick Gammon's Schedule J
// Interrupt code borrows from https://playground.arduino.cc/Main/PinChangeInterrupt

#include <avr/sleep.h>

int key[12][3] = {  //min and max analogRead values for each key in the 3x4 keypad
                  {0,993,1012},
                  {1,848,865},
                  {2,834,847},
                  {3,800,833},
                  {4,901,914},
                  {5,884,900},
                  {6,866,883},
                  {7,948,969},
                  {8,930,947},
                  {9,915,929},
                  {10,1013,1023},
                  {11,970,992}
                 };

void pciSetup(byte pin)
{
    *digitalPinToPCMSK(pin) |= bit (digitalPinToPCMSKbit(pin));  // enable pin
    PCIFR  |= bit (digitalPinToPCICRbit(pin)); // clear any outstanding interrupt
    PCICR  |= bit (digitalPinToPCICRbit(pin)); // enable interrupt for the group
}

ISR (PCINT1_vect) // handle pin change interrupt for A0 to A5 here
 {
     //no need to do anything beyond just waking up.
 }  

 int identifyKey(uint16_t voltage) {
  int i=0;

  while ((i<12) && ((voltage<key[i][1]) || (voltage>key[i][2]))) {
    i++;
  }
  return i;
 }

void setup() {
  pinMode(A0,INPUT);
  pciSetup(A0);
  Serial.begin(115200);
  Serial.println("Starting...");
  Serial.flush();
}

void loop() {
  uint16_t voltage;

  set_sleep_mode (SLEEP_MODE_PWR_DOWN);  
  sleep_enable();

  // Do not interrupt before we go to sleep, or the
  // ISR will detach interrupts and we won't wake.
  noInterrupts ();
  
  pciSetup(A0);
  
  // turn off brown-out enable in software
  // BODS must be set to one and BODSE must be set to zero within four clock cycles
  MCUCR = bit (BODS) | bit (BODSE);
  // The BODS bit is automatically cleared after three clock cycles
  MCUCR = bit (BODS); 
  
  // We are guaranteed that the sleep_cpu call will be done
  // as the processor executes the next instruction after
  // interrupts are turned on.
  interrupts ();  // one cycle
  sleep_cpu ();   // one cycle

  delay(20);  //debounce the button
  voltage=analogRead(A0);  //throw out this first result
  voltage=analogRead(A0);
  if (voltage>799) {
    Serial.println(identifyKey(voltage));
    Serial.flush();
  }
}

Carywin

@gohan Sorry I don't have a way to measure current that small, but given that it's already run for months on the original batteries, I'm going to assume it's a "normal" Atmega sleep state

Carywin

@dbemowsk The Pro Mini does have pin change interrupts on every pin

Carywin

@neverdie This is correct, but this testing is all handled by the EnableInterrupt library

dbemowsk

@carywin I stand corrected.

wes

@wes said in 6/8 Buttons battery remote node:

I'm planning to use some cheap RF remotes and connect a RF receiver to my RPI, which hosts both my gateway and controller.

I finally received the RF remotes and receiver/decoder from eBay and got them set up to talk directly to my controller - they work pretty well: https://youtu.be/9458-3IiG3Y

I did try a OneButton-type approach on a MySensors node, but had lots of malfunctions with long-presses (e.g. fade up 10% per second whilst the button is depressed), where the the "button pressed" message gets through, but the "button released" message is delayed or dropped.

NeverDie

@wes Maybe your resistors don't have a high enough power rating for the current that's running through them? i.e. holding down the button heats them up and therefore changes their resistance? That might explain the slowness to react as expected after the button is released. After release, they cool off and eventually return within their expected resistance tolerance, at which point the expected behavior finally happens.

6/8 Buttons battery remote node

20

11.7k

11.2k

113.1k