💬 Building a Raspberry Pi Gateway
-
Can someone tell me how to apply this patch?
-
@gohan :
dietpi looks interesting! did not know about this yet.
what hardware are you using? and what version of mysgw? -
I need help with my Rpi mqtt-gw.
I tried to get dev-branch working but changed now to stable. All the install routines run without problems. The service just doesn't seem to work and I can't figure out why.- Rpi W, Raspbian wheezy, nRF24-PA, MQTT-gw, Mosquitto and Openhab2 on same board
Mosquitto-log:
1521010232: New connection from 127.0.0.1 on port 1883. 1521010232: New client connected from 127.0.0.1 as mygateway1 (c1, k15, u'xxxx'). 1521010232: Socket error on client mygateway1, disconnecting.syslog:
Mar 14 08:51:02 GwMqOH2 systemd[1]: Starting MySensors Gateway daemon... Mar 14 08:51:02 GwMqOH2 systemd[1]: Started MySensors Gateway daemon. Mar 14 08:51:03 GwMqOH2 mysgw: Starting gateway... Mar 14 08:51:03 GwMqOH2 mysgw: Protocol version - 2.2.0 Mar 14 08:51:03 GwMqOH2 mysgw: MCO:BGN:INIT GW,CP=RNNGLSQX,VER=2.2.0 Mar 14 08:51:03 GwMqOH2 mysgw: TSF:LRT:OK Mar 14 08:51:03 GwMqOH2 mysgw: TSM:INIT Mar 14 08:51:03 GwMqOH2 mysgw: TSF:WUR:MS=0 Mar 14 08:51:03 GwMqOH2 mysgw: TSM:INIT:TSP OK Mar 14 08:51:03 GwMqOH2 mysgw: TSM:INIT:GW MODE Mar 14 08:51:03 GwMqOH2 mysgw: TSM:READY:ID=0,PAR=0,DIS=0 Mar 14 08:51:03 GwMqOH2 mysgw: MCO:REG:NOT NEEDED Mar 14 08:51:03 GwMqOH2 mysgw: MCO:BGN:STP Mar 14 08:51:03 GwMqOH2 mysgw: MCO:BGN:INIT OK,TSP=1 Mar 14 08:51:03 GwMqOH2 mysgw: GWT:RMQ:MQTT RECONNECT Mar 14 08:51:03 GwMqOH2 mysgw: connected to 127.0.0.1 Mar 14 08:51:03 GwMqOH2 mysgw: GWT:RMQ:MQTT CONNECTED Mar 14 08:51:03 GwMqOH2 mysgw: GWT:TPS:TOPIC=mysensors-out/0/255/0/0/18,MSG SENT Mar 14 08:51:03 GwMqOH2 systemd[1]: mysgw.service: main process exited, code=killed, status=11/SEGV Mar 14 08:51:03 GwMqOH2 systemd[1]: Unit mysgw.service entered failed state``` GW configure-line:./configure --my-transport=nrf24 --my-gateway=mqtt --my-controller-ip-address=127.0.0.1 --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18 --my-mqtt-user=xxxx --my-mqtt-password=yyyyy --my-signing=password --my-signing-password=zzzzzz```
I have checked mosquitto has correct user-pw combination, but what should I check next? Help!
- Rpi W, Raspbian wheezy, nRF24-PA, MQTT-gw, Mosquitto and Openhab2 on same board
-
@masmat said in 💬 Building a Raspberry Pi Gateway:
--my-mqtt-client-id=mygateway1
Do you have another client named mygateway1 connecting to mqtt? Try changing it to a different name just to play safe
-
No, you need to recompile it again in case you make that change. Have you ever tried dietpi for RPI?
@gohan OK. I did that, the same socket error remains in Mosquitto just under new id.
Is my syntax correct or am I somehow having problems with mosquitto user-pw...?Haven't tried DietPi. Would Mys+Mosquitto+Openhab2 have trouble running on it? Or why should I change to it?
-
@gohan OK. I did that, the same socket error remains in Mosquitto just under new id.
Is my syntax correct or am I somehow having problems with mosquitto user-pw...?Haven't tried DietPi. Would Mys+Mosquitto+Openhab2 have trouble running on it? Or why should I change to it?
@masmat What is the mqtt broker / version you are using?
-
Can someone tell me how to apply this patch?
@gieljnssns One way is to replace the changed files, in this case EthernetServer.cpp for the first patch and EthernetClient.cpp for the second patch.
You can download from:
https://raw.githubusercontent.com/marceloaqno/MySensors/linux-fix-stability/drivers/Linux/EthernetServer.cpp
https://raw.githubusercontent.com/marceloaqno/MySensors/linux-fix-stability/drivers/Linux/EthernetClient.cppHere is a step-by-step:
git clone https://github.com/mysensors/MySensors.git cd MySensors curl https://raw.githubusercontent.com/marceloaqno/MySensors/linux-fix-stability/drivers/Linux/EthernetServer.cpp -o drivers/Linux/EthernetServer.cpp curl https://raw.githubusercontent.com/marceloaqno/MySensors/linux-fix-stability/drivers/Linux/EthernetClient.cpp -o drivers/Linux/EthernetClient.cppfrom here just run ./configure with your options and then make
-
@masmat What is the mqtt broker / version you are using?
@marceloaqno Mosquitto v1.4.14.
The broker is working, at least sending & receiving command line (_sub & _pub) messages. -
I'm using dietpi and I am not having big issues even running 2 gateway instances with 2 different radios
Can you provide some installation instructions for dietpi?
I will try this... -
@marceloaqno :
Hi, unfortunately the latest patch did not work for me.
Still the gw stops receiving, but without high cpu usage :-(
Fortunately I can restart the gw now using a button and this udp-scripts :-)Of cource I could give dietpi a try, but I would think, that a general solution would be better (for other users as well)
cheers,
Otto -
just download the image and do the same as a Raspian image. I haven't tried mqtt gateway yet, so I don't know if it may be a gateway bug or else.
@gohan I had another sd card and tried a ready image of DietPi with Mosquitto pre-installed.
I tried it without user/password and mosquitto accepting anonymous but:/var/log/mosquitto/mosquitto.log:
1521141160: Socket error on client <unknown>, disconnecting.
1521141160: New connection from 127.0.0.1 on port 1883.
..keeps repeating......and sudo ./bin/mysgw -d:
mysgw: Starting gateway... mysgw: Protocol version - 2.2.0 mysgw: MCO:BGN:INIT GW,CP=RNNGLSQX,VER=2.2.0 mysgw: TSF:LRT:OK mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: MCO:BGN:STP mysgw: MCO:BGN:INIT OK,TSP=1 mysgw: GWT:RMQ:MQTT RECONNECT mysgw: connected to 127.0.0.1 mysgw: GWT:RMQ:MQTT RECONNECT mysgw: connected to 127.0.0.1 mysgw: GWT:RMQ:MQTT RECONNECT``` -
1st patch is still working good for me. have had no issues since applying it.
question. is it normal/correct for the gateway to ping or spam? every 10 seconds i see the gateway announce it's version.
its not doing the full restart or anything.. just giving the 2.2.0 every 10 seconds. -
@gohan I had another sd card and tried a ready image of DietPi with Mosquitto pre-installed.
I tried it without user/password and mosquitto accepting anonymous but:/var/log/mosquitto/mosquitto.log:
1521141160: Socket error on client <unknown>, disconnecting.
1521141160: New connection from 127.0.0.1 on port 1883.
..keeps repeating......and sudo ./bin/mysgw -d:
mysgw: Starting gateway... mysgw: Protocol version - 2.2.0 mysgw: MCO:BGN:INIT GW,CP=RNNGLSQX,VER=2.2.0 mysgw: TSF:LRT:OK mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: MCO:BGN:STP mysgw: MCO:BGN:INIT OK,TSP=1 mysgw: GWT:RMQ:MQTT RECONNECT mysgw: connected to 127.0.0.1 mysgw: GWT:RMQ:MQTT RECONNECT mysgw: connected to 127.0.0.1 mysgw: GWT:RMQ:MQTT RECONNECT``` -
-
@gohan I configured:
./configure --my-transport=nrf24 --my-gateway=ethernet --my-controller-ip-address=127.0.0.1 --my-rf24-irq-pin=15 --my-leds-err-pin=12 --my-leds-rx-pin=16 --my-leds-tx-pin=18 --my-signing=password --my-signing-password=ZZZZZZ./bin/mysgw -d:
mysgw: Starting gateway... mysgw: Protocol version - 2.2.0 mysgw: MCO:BGN:INIT GW,CP=RNNGLSQX,VER=2.2.0 mysgw: TSF:LRT:OK mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: connect: Connection refused mysgw: failed to connect mysgw: GWT:TIN:ETH OK mysgw: connect: Connection refused mysgw: failed to connect mysgw: GWT:TPS:ETH OK mysgw: connect: Connection refused mysgw: failed to connect mysgw: GWT:TPS:ETH OKThe controller doesn't exist on the DietPi card yet but I'm not sure if that's causing the problem.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login