Sensor taking the status of a blinking led of an alarm system

[BulldogLowell]

@Meister_Petz

I would open the alarm interface and solder in a couple of small wires... you don't want any ambient light n the photocell and covering the led seems ugly...

then use the method @Tibus mentioned... use an interrupt on CHANGE and a timer to transmit off status if the timer expires.

It think it would be prettier and more reliable. If you are living with a spouse or significant other, you will see the benefits!

PS you can power the whole thing from the alarm interface ... try checking the power voltage to the interface. all you need is at least 3V3 and a few caps. you may be able to fit the pro-mini and the radio inside the interface!

[Meister_Petz]

@Tibus
being new at programmig for arduino, I'm not really sure how to put this into code :-(
could you give me an code example how you do that?

@BulldogLowell
I agree! When the warranty runs out, I'll take the opening and soldering approach ;-) But even at the moment it's not that bad, because the Alarmterminal is hidden and for switching it on, I use my controller.

Many thanks for your help!
Petz

[BulldogLowell]

@Meister_Petz

if you need it to run on battery, then you may not want to bother with sleep, since you are looking for the non-occurrence of something. ;)

the interrupt method will wake the MCU every time the led flashes...

you could start with code like this (untested):

EDITED

#include <MySensor.h>  
#include <SPI.h>

typedef enum{
  NOT_ARMED = 0, ARMED
} 
AlarmState;

AlarmState state;

AlarmState lastAlarmState;

unsigned long lastFlashTime;

#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your light sensor

#define CHILD_ID 1   // Id of the sensor child

MySensor gw;
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()  
{ 
  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input 
  gw.begin();
  gw.sendSketchInfo("Motion Sensor", "1.0");
  delay(1000);
  gw.present(CHILD_ID, S_MOTION);
  delay(1000);
}

void loop()     
{     
  // Read digital light sensor value
  if (digitalRead(DIGITAL_INPUT_SENSOR) == HIGH)
  {
    lastFlashTime = millis();
    state = ARMED;
    if (lastAlarmState == NOT_ARMED)
    {
      gw.send(msg.set(ARMED));  // Send tripped value to gw 
    } 
  }
  if (lastFlashTime - millis() > 5000UL && state == ARMED) // you may have to adjust... this is 5 seconds
  {
    state = NOT_ARMED;
    if (lastAlarmState == ARMED)
    {
      gw.send(msg.set(NOT_ARMED));  // Send not tripped value to gw 
    }
  }
  lastAlarmState = state;
}

[Meister_Petz]

Many Thanks for the code, I will start to play around asap ;-)

[BulldogLowell]

@Meister_Petz

OK, just check the edit... so it is not banging away at your gateway!!!

[Meister_Petz]

btw, thats was my working apporach before:
is there a nice way to add code? Do I really have to add 4 spaces before every line?

[daulagari]

is there a nice way to add code? Do I really have to add 4 spaces before every line?

Yes, that is the way to format code.

But ... knowing some tools there is no need to do it by hand. In vi/vim:

:%s/^/    /

[hek]

@daulagari

or just surround code-block with 3 backtick-characters. This character ----> `

#include <hehe.h>

printf();

[BulldogLowell]

@Meister_Petz

or in your arduino editor, just grab all the code (CTRL+A) and then increase indent twice... on my mack it is (COMMAND+ ]) That moves all the code right four spaces... see below:

[Meister_Petz]

MANY THANKS!

That is what I did until now without Millis and interupts,...

In this code I determine blinks by the difference between 2 following readings. Is there a better way?

And I simplified the message sent to the gateway quite a bit. Do I produce any errors with this?

  /* Small sketch to determine the State of a Olympia Protect Alarmsystem
  0. When UNARMED   : LED off - DISPLAY off
  1. When ARMED     : LED blinks
  2. When ACTIVATING: LED blinks - DISPLAY blinks (check if before State was ARMED)
  3. When TRIGGERED : LED blinks - DISPLAY blinks (check if before State was ARMED)
  */
  
  #include <MySensor.h>
  #include <SPI.h>
  #define CHILD_ID 3
  MySensor gw;
  MyMessage msg(CHILD_ID,V_TRIPPED);
  
  const int phCell1Pin = 0; // Photocell 1 on PIN 0 - Display
  const int phCell2Pin = 1; // Photocell 2 on PIN 1 - LED
  const int phCell1Sensitivity = 100; // sets the minimum difference between two readings to determine blinking of Display
  const int phCell2Sensitivity = 100; // sets the minimum difference between two readings to determine blinking of LED
  const int sleepTime = 7000; // 7 Sec. between Reading Cycles
  int armingTime = 30; // Seconds set until arming is done
  
  
  int DisplayState = 0;
  int LEDState = 0;
  int AlarmSystemState = 4; // (0 = Off, 1 = On, 2 = Activating, 3 = Triggered)
  int AlarmSystemStateOld = 0;
  int myRound1[10] = {0,0,0,0,0,0,0,0,0,0}; // Array to store Readings
  int myRound2[10] = {0,0,0,0,0,0,0,0,0,0}; // Array to store Readings
  int goSleep = 0;
  int i = 0;
  int i1 = 0;
  int i2 = 0;
  
  void setup(void) {
    gw.begin();
    gw.present(CHILD_ID, S_DOOR);
  }
   
  void loop(void) {
       if (i < 10){ // 10 Readings
         myRound1[i] = analogRead(phCell1Pin); // read Photosensor Display 
         //Serial.print("Display PhCell:"); Serial.println(myRound1[i]);
         myRound2[i] = analogRead(phCell2Pin); // read Photosensor LED 
         //Serial.print("LED     PhCell:"); Serial.println(myRound2[i]);
         
         if (i > 0){ // compare 2 following readings
           // Display
           if ((myRound1[i] - myRound1[i-1]) > phCell1Sensitivity){i1++;}
           if ((myRound1[i-1] - myRound1[i]) > phCell1Sensitivity){i1++;}
           // LED
           if ((myRound2[i] - myRound2[i-1]) > phCell2Sensitivity){i2++;}
           if ((myRound2[i-1] - myRound2[i]) > phCell2Sensitivity){i2++;}
         }
         i++;
         
       } else {
         
         // Display
         if (i1 > 2){ // if there are more than 3 Readings which are assumed blinks - set DisplayState to blink
           DisplayState = 1; //Serial.println("Display blinkt - State 1");
         } else {
           DisplayState = 0; // Serial.println("Display dunkel - State 0");
         }
         
         //LED
         if (i2 > 2){ // if there are more than 3 Readings which are assumed blinks - set LEDState to blink
           LEDState = 1; //Serial.println("LED blinkt - State 1");
         } else {
           LEDState = 0; // Serial.println("LED dunkel - State 0");
         }
  
         goSleep = 1; // now transmit if necessary and wait before starting again
         // Reset
         i = 0;
         i1 = 0;
         i2 = 0;
         int myRound1[10] = {0,0,0,0,0,0,0,0,0,0};
         int myRound2[10] = {0,0,0,0,0,0,0,0,0,0};
       }
  
       // send to Sleep
       if (goSleep == 1){
         if (DisplayState == 0 && LEDState == 0){
           AlarmSystemState = 0; // OFF
         } else if (DisplayState == 0 && LEDState == 1){
           AlarmSystemState = 1; // ON
         } else if (DisplayState == 1 && LEDState == 1 && AlarmSystemStateOld == 0){
           AlarmSystemState = 2; // Actviating
           //delay(70000); // wait 70 Seconds until Activating is done 
         } else if (DisplayState == 1 && LEDState == 1 && AlarmSystemStateOld == 1){
           AlarmSystemState = 3; // TRIGGERED
         } else {
          AlarmSystemState = AlarmSystemStateOld;
         }
         
  
         // Send State change to Gateway
         //Serial.print("AlarmSystemState Änderung:");Serial.println(AlarmSystemState);
         gw.send(msg.set(AlarmSystemState));
         
         if (AlarmSystemState == 2){ // Delay until Arming is done before next read
           armingTime = (armingTime * 1000)+1000;
           delay(armingTime);
         }
         
         AlarmSystemStateOld = AlarmSystemState;
         delay(sleepTime);
         goSleep = 0;
       } else {
         delay(575);
       }
  }

[Tibus]

@BulldogLowell said:

if you need it to run on battery, then you may not want to bother with sleep, since you are looking for the non-occurrence of something.

the interrupt method will wake the MCU every time the led flashes...

you could start with code like this (untested):

why not use sleep. Yes it will wake the MCU every time the led flashes but it 'll consume less power when it sleep. you can go from 7ma to 10ua when it sleep. Even for one seconds it's a benefit no?

[brettzky84]

Why not measure when there is voltage to the led??? Much more reliable and simple

[BulldogLowell]

@Tibus said:

why not use sleep.

you are correct, of course. I look at it as a two step approach:

1. get it to work
2. get it to work better than before

[Meister_Petz]

@Tibus
I agree about sleeping. But for one thing I don't have the slightest clue how working with interupts works (yet) and the Arduino is hook on the power of the Alarmsystem ;-)

BTW my Alarmsystem Powersupply produces 6V. Would it make more sense to use a 5V Step Down Regulator and give power to pin 27 (5V) than 6V to PIN 30 (VIN)?

Many Thanks

Petz

[BulldogLowell]

@Meister_Petz

Pro-Mini? I'd just take the 6V to the RAW pin.

6V to Vin on a nano.

[Meister_Petz]

Nano - so VIN! Thanks!