💬 EFEKTA Temperature & Humidity mini sensor

[berkseo]

@mika said in 💬 EFEKTA Temperature & Humidity mini sensor:

Hi,
exist some enclosures for your sensors?
MiKa

Hi, this is a problem, for now, I do it, but I practically have no time for it. But I will definitely make them myself. Maybe I will do them on industrial equipment, if some people like my devices, now they are testing them :)

[jeti]

@berkseo do you have a 3d Model of the Sensor? I could support with designing a housing if you want!

[terxw]

What is the serial upload speed?

[berkseo]

@terxw ...as usual, 115200 (max). And why such question???

[berkseo]

@jeti Sorry, I did not answer. No, I do not have a 3D model. I can send you a device using components. It would be great if there were cases for devices from third-party developers.

[magpern]

Could you upload the schematics or some guide of what component goes where?

[berkseo]

Started the development of the case...

Remember to support the project with your likes !!! :)

[berkseo]

@berkseo
Update, the hull prototype is ready. Developed at SOLIDWORKS. It was printed on a 3D printer type SLA. Trial printing on opaque resins has been started. This case cannot be reproduced on the printer type FDM.

[berkseo]

@berkseo

[berkseo]

Completed the transfer of 3D models to non-transparent plastics

[Yveaux]

@berkseo what's the function of the 2 buttons?

[berkseo]

@yveaux

One button is reset, the second button is multifunctional. Depends on how many seconds you hold this button. In my program, I use this button to connect via air to other devices and to transfer the device to receive settings (data transmission intervals, led operation and so on). This button is not used in my test sketch

An example of direct connection between devices (without the use of controllers, without changing the SOFTWARE) is my development, which is in the testing stage is the controller of Underfloor heating. This device controls the five contours of the Underfloor heating. Up to 10 such temperature sensors can be connected to this device simply by pressing the connect button. Maximum of two temperature sensors per one relay channel.

https://youtu.be/8mvJFieInsM

https://youtu.be/kXsxtYVbNAw

https://youtu.be/NyNFx7sd9ZE

Examples of direct connections (micro-networks) based on MySensors can be found here:

https://youtu.be/jFDBeInBZcI

https://youtu.be/x1oNCO0TXG8

https://youtu.be/h8Ly_JRFwLg

[berkseo]

https://youtu.be/puOXej1odeU

[jeremushka]

Is it possible for you to share the sketch as it has been removed from the project presentation because of the rules of the website?

[berkseo]

@jeremushka said in 💬 EFEKTA Temperature & Humidity mini sensor:

Is it possible for you to share the sketch as it has been removed from the project presentation because of the rules of the website?

https://www.openhardware.io/view/589#tabs-source

[berkseo]

Finished the enclosure for the sensor on the battery 2477 (1000mA) :)

https://youtu.be/XWu5sogiiQg

[berkseo]

To install the sensor on the wall, I recommend 3M adhesive strips (with easy removal)

[berkseo]

Some more photos... :)

[jeremushka]

@berkseo said in 💬 EFEKTA Temperature & Humidity mini sensor:

@jeremushka said in 💬 EFEKTA Temperature & Humidity mini sensor:

Is it possible for you to share the sketch as it has been removed from the project presentation because of the rules of the website?

https://www.openhardware.io/view/589#tabs-source

Thank you very much. Great casing, it is very discret. professional design. congratulations :)

[berkseo]

@jeremushka

Thanks. This is actually my first experience in designing sensor housings. I've never done 3D modeling before. A month and a half ago I started watching a video on YouTube on modeling in SolidWorks. With printing on a 3D printer is also my first experience.