Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Is there still a breakout board for the Atmel ATSHA204A chip?

evb last edited by

Hi,

Was searching how to implement the Atmel ATSHA204A chip as a signing hardware device in the gateway and the sensor nodes.
Found the chip on AliExpress quickly, but it is only available as smd component, so was searching for a breakout board.
There was once a breakout board done by Sparkfun, but it isn't made anymore (https://www.sparkfun.com/products/retired/11551)

Searching with our friend Google did not reveal any other manufacturers

Does someone knows about a breakout board for this chip?
Or is my only choice to use these little smd component ?
Reply Quote 0
1 Reply Last reply

1
Posts

356
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Gateway on Raspberry pi 1
General Discussion • • mimaret

9

0
Votes

9
Posts

44
Views

@mimaret It was a pleasure. Thank you for your feedback!
Running out of nodeId's
General Discussion • mysensors • • NielBierman

8

3
Votes

8
Posts

47
Views

@TheoL Not only did I put in delays, too, but I put in delays that were based upon the ID (which was stored in NVRAM)! This helped. caveat: This is probably not accurate be helps to explain the challenges with a large network. My initial experience with Arduino/nRF24 was using the libraries from TMRh20. Those libraries allowed a node to be a repeater, but only for 6 nodes. The primary node 0, master, only allowed 6 nodes to connect to it. The nodes connected to it also allowed 6 nodes. Subsequent nodes had to go through one of these repeating nodes. But the depth was only 4 deep. The master assigned node IDs if the node didn't already have one; similar to a MAC address. The master also kept track of the addresses (ARP table?). Addresses were 4 octets (base in the form of D/C/B/A. A node connected directly to the master had an address of 0/0/0/a (where 0/0/0/0 was reserved for the master). A node connected through another node had an address of 0/0/b/a, and so forth. But what happens is that a parent node has to mange the data from all its child nodes and their child nodes and their child nodes. Thus a node would get so bogged down dealing with this traffic that it din't do its sensor task very well. It is my belief that MySensors either uses TMRh20's libraries or has developed some aspects based on his initial work. I see that that TMRh20 has a version 2 and I have not experimented with it. I did find that MySensors worked better than version 1. Thus, my curiosity. I am also duly impressed at the magnitude of hardware. Currently a nano like device from Aliexperss is US$2-3, nRF24 ~ US$1, power supply ~ US$1.50, power cord ?, case?, sensors!? While the hardware cost is daunting, even with a PCB it's a lot of work building those up. So, yeah, I'm impressed! -OSD
Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

4

0
Votes

4
Posts

21
Views

Thanks for the offer @TheoL ! I have moved on to a differenct project. Also, a lesson that I have learned many times, "If it works, don't fix it!" -OSD
Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

17

0
Votes

17
Posts

166
Views

LiFePO4 batteries are a great choice because they have a long life cycle and are much safer than other lithium-based batteries. However, you need a solar charge controller that’s compatible with LiFePO4 to prevent overcharging and maintain efficiency. A good MPPT controller can significantly boost energy harvest from your panels. Also, ensure your solar panel output matches your power needs. If you're in solar ireland, you might find some local companies that offer tailored solutions for maximizing solar efficiency in lower light conditions.
Old hardware migration
General Discussion • • dbemowsk

3

0
Votes

3
Posts

38
Views

@OldSurferDude My old 2.0 setup is with nRF24L01 radios. This is a link to the thread on some light switches that I designed and built. https://forum.mysensors.org/topic/7376/us-decora-wall-switch-continued/2 I am aware that you cannot have two MQTT gatways. When I designed my old setup I was not that familiar with MQTT so I never ended up implementing it. On the home assistant server that I have set up though, I have installed the MQTT broker on there so I should be able to comunicate with any MySensors stuff over MQTT in the future devices I make/set up. As I mentioned, I do have a Home Assistant box that I have started about 4 months ago and eventually want to migrate my Vera equipment to the HA box. As for the YAML and Python, I'll muddle my way through. used to program in PHP and have done enough on Arduino that I'm sure it won't hurt my brain too much.

Is there still a breakout board for the Atmel ATSHA204A chip?

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

Gateway on Raspberry pi 1
General Discussion • • mimaret

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

Old hardware migration
General Discussion • • dbemowsk

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Is there still a breakout board for the Atmel ATSHA204A chip?

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

Gateway on Raspberry pi 1 General Discussion • • mimaret

Running out of nodeId's General Discussion • mysensors • • NielBierman

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini? General Discussion • • kiesel

Need advice on solar powering with LiFePo4 battery General Discussion • • willemx

Old hardware migration General Discussion • • dbemowsk

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Update RF24 library to latest version
Bug Reports • • andriej

Gateway on Raspberry pi 1
General Discussion • • mimaret

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Anybody got one / a few spare minimalist rfm69hw shields for wemos d1 mini?
General Discussion • • kiesel

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

Old hardware migration
General Discussion • • dbemowsk

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts