ESP8266Wifi Gateway won't connect

[hard-shovel]

@dpcons I assembled a board copied from yours for testing.

I could replicate the problem. It is with the ESP core version and the MySensor Version
MySensors version 2.3.2 and ESP8266 core 3.0.2 does not work,

MySensors version 2.3.2 and ESP8266 core 2.7.4 works

Mysensors development version 2.4.0-Alpha and newest ESP8266 core 3.0.2 also works

So you can either update the esp core to older version 2.7.4, or install the development version of MySensors 2.4.0-Alpha

[paqor]

@hard-shovel said in ESP8266Wifi Gateway won't connect:

MySensors version 2.3.2 and ESP8266 core 2.7.4 works

[chrishiscox]

@hard-shovel I had same issue and using older version worked for me too

[dpcons]

@hard-shovel Thanks so much for your effort and your timely resolution. I tried going back with previous versions of the library and they didn't work or didn't compile. I greatly appreciate your help with this. I assume something similar is happening to the ESP32 version also. Again, thanks.

[OldSurferDude]

@dpcons @hard-shovel @paqor @chrishiscox @mfalkvidd Hi all,

I saw this and got excited that I could use my NodeMCUv1.0 as a MySensors Gateway. I made sure I had the latest MySensors library (2.3.2) and ESP8266 board (3.0.2). I successfully ran a couple examples, first file-->examples-->ESP8266-->Blink then file-->examples-->ESP8266-->interactive (with my ssid & pass), the latter with serial monitor at 115200 baud.

I ensured that my nRF24l01 was functional by connecting it to an Arduino Nano and running the scanner program.

I connected my nRF24l01 to my NodeMCU, both having pins, using new 10cm 7 conductor ribbon cable. (I have successfully used this type of connection to an RPi)

The program ... I copied the program from this page and applied my ssid and password. Nothing ... I suspected that this code is a node template, not a the gateway program.

On that same page was the instruction "Open the WiFi gateway in the Arduino IDE (File -> Sketchbook -> Libraries -> MySensors -> Esp8266Gateway)" I didn't find "Libraries" under "Sketchbook" I a file of the same name at (File -> Sketchbook -> Libraries -> MySensors -> examples --> Esp8266Gateway) which is the same file.

I tried putting into setup the line

Serial.println("com check");

but nothing came out on the console.

I think I'm at the same place as @dpcons

update: rechecked my radio with the RF24 "getting started" program and found the radio good. Updated my Arduino IDE. Still not working.

[hard-shovel]

@OldSurferDude @dpcons Hi all,
The sample sketch could also be found using (File -> Examples -> MySensors -> Esp8266Gateway

As MySensors version 2.3.2 and ESP8266 core 3.0.2 combination does not work you need to change one or the other versions.

The simplest is to roll back the ESP8266 Core version to 2.7.4 and keep the MySensors 2.3.2 version
(Tools -> Board -> Board Manager)
Enter ESP8266 in search bar, then click within the ESP8266 data info box, click the select version pulldown.
Select 2.7.4 and then click Install.

Other option is to update the MySensors library to the development version 2.4.0-Alpha but that has to be done manually.

[OldSurferDude]

@hard-shovel Thanks! Now I'm getting output to the monitor. I think I need to set up the IP address and the port 1883 for the MQTT broker. How is that done? I am also getting data from my Arduino node sensors :) I see "controller" but when I change that to my broker's address I get streaming ETH FAIL

[OldSurferDude]

The port was set to 5003 and setting it to 1883 (the default MQTT broker port) it now seems to work

[hard-shovel]

@OldSurferDude If connecting to a MQTT Broker i would have expected you to use the GatewayESP8266MQTTClient sketch.
as this is already setup with correct Port 1883 for MQTT and the publishing and subscription topics.

I did a quick test of a GatewayESP8266MQTTClient sketch with mosquitto and it works fine for me.

[OldSurferDude]

@hard-shovel While it all seemed to be working, it appears that the ESP8266 MySensors Gateway was not passing the data onto the MQTT broker. Working, meaning that data from the Arduino sensors were getting to the Gateway, but that data was not getting to the broker. Here are some lines of the debug output:

6217818 TSF:MSG:READ,133-133-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
6217883 TSF:MSG:BC
6217903 TSF:MSG:FPAR REQ,ID=133
6217936 TSF:CKU:OK,FCTRL
6217962 TSF:MSG:GWL OK
6218281 !TSF:MSG:SEND,0-0-133-133,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 

Also, as an indication that data was not being passed from the Gateway to the broker, I had reset my MQTT Broker and subsequently monitored it with MQTT explorer. The topic "mysensors-out" was not created.

I shut down the ESP8266 MySensors Gateway and restarted the my original one that is running on an RPi. Everything started running as expected.

Thus, my conclusion.

OK, so why isn't the ESP8266 MySensors Gateway passing on the data?

[OldSurferDude]

@hard-shovel I try the client

[OldSurferDude]

@hard-shovel client worked for me, too. That is, it sent the message "2.3.2" to topic "mygateway1-outx/0/255/0/0/18"

[OldSurferDude]

@hard-shovel I tried the client and it did indeed send the MySensors version message. But it does not pass along the messages from the Arduino nodes.

[hard-shovel]

@OldSurferDude have you set the MQTT user and MQTT passwords in the sketch and uncommented them as well?

// Enable these if your MQTT broker requires usenrame/password
//#define MY_MQTT_USER "username"
//#define MY_MQTT_PASSWORD "password"

// Enable these if your MQTT broker requires usenrame/password
#define MY_MQTT_USER "MQTTusername2022"
#define MY_MQTT_PASSWORD "MQTTpassword2022"

what does your debug log look like?
This sample is not connected correctly to the MQTT Broker

10:33:26.151 -> dhcp client start...
10:33:26.151 -> 341 TSM:INIT:GW MODE
10:33:26.199 -> 364 TSM:READY:ID=0,PAR=0,DIS=0
10:33:26.199 -> 396 MCO:REG:NOT NEEDED
10:33:26.339 -> 505 GWT:TPC:CONNECTING...
10:33:27.365 -> 1533 MCO:BGN:STP
10:33:27.365 -> 1551 MCO:BGN:INIT OK,TSP=1
10:33:27.412 -> 1579 TSM:READY:NWD REQ
10:33:27.412 -> 1606 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
10:33:28.671 -> scandone
10:33:35.993 -> pm open,type:2 0
10:33:44.664 -> 18861 TSF:MSG:READ,254-254-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
10:33:44.758 -> 18924 TSF:MSG:BC
10:33:44.758 -> 18942 TSF:MSG:FPAR REQ,ID=254
10:33:44.804 -> 18973 TSF:PNG:SEND,TO=0
10:33:44.804 -> 18998 TSF:CKU:OK
10:33:44.851 -> 19016 TSF:MSG:GWL OK
10:33:45.459 -> 19646 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
10:33:46.671 -> 20876 TSF:MSG:READ,254-254-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
10:33:46.766 -> 20939 TSF:MSG:PINGED,ID=254,HP=1
10:33:46.813 -> 20980 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
10:33:46.860 -> 21057 TSF:MSG:READ,254-254-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100

This is working correctly

10:36:34.908 -> dhcp client start...
10:36:37.655 -> ip:192.168.1.202,mask:255.255.255.0,gw:192.168.1.254
10:36:37.702 -> 7014 GWT:TPC:IP=192.168.1.202
10:36:37.702 -> 7100 GWT:RMQ:CONNECTING...
10:36:37.749 -> 7144 GWT:RMQ:OK
10:36:37.795 -> 7161 GWT:TPS:TOPIC=mygateway4-out/0/255/0/0/18,MSG SENT
10:36:44.792 -> pm open,type:2 0
10:38:56.629 -> 146027 TSF:MSG:READ,254-254-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
10:38:56.723 -> 146091 TSF:MSG:BC
10:38:56.723 -> 146109 TSF:MSG:FPAR REQ,ID=254
10:38:56.770 -> 146142 TSF:PNG:SEND,TO=0
10:38:56.770 -> 146168 TSF:CKU:OK
10:38:56.816 -> 146187 TSF:MSG:GWL OK
10:38:57.655 -> 147013 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
10:38:58.683 -> 148042 TSF:MSG:READ,254-254-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
10:38:58.730 -> 148105 TSF:MSG:PINGED,ID=254,HP=1
10:38:58.776 -> 148148 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
10:38:58.869 -> 148226 TSF:MSG:READ,254-254-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
10:38:58.916 -> 148294 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
10:38:59.010 -> 148375 TSF:MSG:READ,254-254-0,s=255,c=0,t=17,pt=0,l=11,sg=0:2.4.0-alpha
10:38:59.058 -> 148450 GWT:TPS:TOPIC=mygateway4-out/254/255/0/0/17,MSG SENT
10:38:59.151 -> 148515 TSF:MSG:READ,254-254-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
10:38:59.197 -> 148578 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/6,MSG SENT
10:39:00.923 -> 150319 TSF:MSG:READ,254-254-0,s=255,c=3,t=11,pt=0,l=14,sg=0:MockMySensors 
10:39:01.017 -> 150398 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/11,MSG SENT
10:39:01.064 -> 150462 TSF:MSG:READ,254-254-0,s=255,c=3,t=12,pt=0,l=4,sg=0:v0.5
10:39:01.157 -> 150529 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/12,MSG SENT
10:39:01.949 -> 151337 TSF:MSG:READ,254-254-0,s=1,c=0,t=0,pt=0,l=12,sg=0:Outside Door
10:39:02.044 -> 151410 GWT:TPS:TOPIC=mygateway4-out/254/1/0/0/0,MSG SENT
10:39:02.091 -> 151471 TSF:MSG:READ,254-254-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
10:39:02.184 -> 151542 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
10:39:02.699 -> 152055 TSF:MSG:READ,254-254-0,s=255,c=3,t=0,pt=1,l=1,sg=0:83

[OldSurferDude]

@hard-shovel My MQTT broker does not require them. Should I uncomment and leave them blank?

[hard-shovel]

@OldSurferDude You should leave them commented if not required.

I have just tested with a new install on windows of mosquitto with config file for anonymous access and it is working fine with them commented out.

what do your gateway debug logs look like?

[OldSurferDude]

@hard-shovel This is what I'm getting (with no nodes connecting to gateway)

MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
117 TSF:LRT:OK
133 TSM:INIT
147 TSF:WUR:MS=0
170 TSM:INIT:TSP OK
191 TSM:INIT:GW MODE
213 TSM:READY:ID=0,PAR=0,DIS=0
245 MCO:REG:NOT NEEDED
scandone
1322 GWT:TIN:CONNECTING...
2351 GWT:TIN:CONNECTING...
scandone
state: 0 -> 2 (b0)
4097 GWT:TIN:CONNECTING...
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt

connected with Automation, channel 9
dhcp client start...
ip:192.168.1.30,mask:255.255.255.0,gw:192.168.1.193
4316 GWT:TIN:IP: 192.168.1.30
4355 GWT:TIN:ETH OK
4378 MCO:BGN:STP
4396 MCO:BGN:INIT OK,TSP=1
4424 TSM:READY:NWD REQ
4451 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
pm open,type:2 0

And this comes when a node connects:

197868 TSF:MSG:READ,2-2-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
197928 TSF:MSG:BC
197947 TSF:MSG:FPAR REQ,ID=2
197977 TSF:PNG:SEND,TO=0
198003 TSF:CKU:OK
198022 TSF:MSG:GWL OK
198460 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
200006 TSF:MSG:READ,2-2-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
200065 TSF:MSG:PINGED,ID=2,HP=1
200106 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
200244 TSF:MSG:READ,2-2-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
200309 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
200385 TSF:MSG:READ,2-2-0,s=255,c=0,t=17,pt=0,l=5,sg=0:2.3.2
200456 GWT:TSA:ETH OK
200481 TSF:MSG:READ,2-2-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
200545 GWT:TSA:ETH OK
202529 TSF:MSG:READ,2-2-0,s=255,c=3,t=11,pt=0,l=15,sg=0:BatMoistHumTemp
202611 GWT:TSA:ETH OK
202636 TSF:MSG:READ,2-2-0,s=255,c=3,t=12,pt=0,l=9,sg=0:     0.01
202710 GWT:TSA:ETH OK
202885 TSF:MSG:READ,2-2-0,s=0,c=0,t=35,pt=0,l=0,sg=0:
202948 GWT:TSA:ETH OK
203141 TSF:MSG:READ,2-2-0,s=1,c=0,t=7,pt=0,l=0,sg=0:
203203 GWT:TSA:ETH OK
203396 TSF:MSG:READ,2-2-0,s=2,c=0,t=6,pt=0,l=0,sg=0:
203458 GWT:TSA:ETH OK
203651 TSF:MSG:READ,2-2-0,s=3,c=0,t=30,pt=0,l=0,sg=0:
203713 GWT:TSA:ETH OK
203925 TSF:MSG:READ,2-2-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
203992 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
204128 TSF:MSG:READ,2-2-0,s=255,c=3,t=0,pt=1,l=1,sg=0:100
204199 GWT:TSA:ETH OK
204407 TSF:MSG:READ,2-2-0,s=3,c=1,t=38,pt=7,l=5,sg=0:6.52
204475 GWT:TSA:ETH OK
204542 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:1023
204610 GWT:TSA:ETH OK

[paqor]

Hello have with the gateway constantly disconnects after a few days and I can only reactivate it by resetting on the gateway.

Have now inserted a separate power supply with a large electrolytic capacitor 5000 µF-let's see....

[hard-shovel]

@OldSurferDude You are getting regular GWT:TSA:ETH OK message which i do not and you have no
MSG SENT lines

Which MQTT broker are you using?

my test setup which i hope matches yours is:
MySensors 2.3.2 & ESP8266 core 2.7.4
ESP8266 Node MCU with sketch GatewayESP8266MQTTClient
MY_BAUD_RATE 9600
MY_MQTT_USER & MQTT_PASSWORD commented out
MY_CONTROLLER_IP_ADDRESS 192, 168, 1, 195 address of the MQTT broker
MY_CONTROLLER_URL_ADDRESS "MQTT-TEST-W10" commented out Use IP or URL not Both
MY_PORT 1883

MQTT Broker
Mosquitto 2.0.15 running as a service on a windows 10 machine
listener 1883 anonymous access
URL MQTT-TEST-W10

When connected to the MQTT Broker and receiving messages from a node the gateway shows

09:48:18.962 -> 718935 TSF:MSG:READ,254-254-0,s=1,c=1,t=16,pt=2,l=2,sg=0:0
09:48:19.010 -> 718997 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/16,MSG SENT

09:48:19.104 -> 719059 TSF:MSG:READ,254-254-0,s=1,c=1,t=15,pt=1,l=1,sg=0:1
09:48:19.149 -> 719121 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/15,MSG SENT

09:48:19.198 -> 719182 TSF:MSG:READ,254-254-0,s=255,c=3,t=0,pt=1,l=1,sg=0:83
09:48:19.292 -> 719246 GWT:TPS:TOPIC=mygateway5-out/254/255/3/0/0,MSG SENT

if a message is sent to the broker the gateway shows

10:03:54.285 -> 1654209 GWT:IMQ:TOPIC=mygateway5-in/254/255/1/0/15, MSG RECEIVED
10:03:54.331 -> 1654279 TSF:MSG:SEND,0-0-254-254,s=255,c=1,t=15,pt=0,l=1,sg=0,ft=0,st=OK:1
10:03:54.423 -> 1654358 TSF:MSG:READ,254-254-0,s=1,c=1,t=16,pt=2,l=2,sg=0:1
10:03:54.471 -> 1654421 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/16,MSG SENT
10:03:54.565 -> 1654483 TSF:MSG:READ,254-254-0,s=1,c=1,t=15,pt=1,l=1,sg=0:1
10:03:54.611 -> 1654546 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/15,MSG SENT

[OldSurferDude]

@hard-shovel I created a faux nano sensor and used nRF24L01 channel 121 to communicate to the gateway. Here is my NodeMCU ESP8266 code with all comments taken out:

#define VER 0.4
#define MY_DEBUG true
#define MY_BAUD_RATE 9600
#define MY_RADIO_RF24
#define MY_RF24_CHANNEL 121
#define MY_GATEWAY_ESP8266 "Test"
#define MY_WIFI_SSID "SSID"
#define MY_WIFI_PASSWORD "pass"
#define MY_HOSTNAME "ESP8266_GW"
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mysensors-out"
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mysensors-in"
#define MY_PORT 1883
#define MY_GATEWAY_MAX_CLIENTS 8
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 1, 142
#include <MySensors.h>
void setup() {Serial.print("ESP8266MySensorsGateway version: ");Serial.println(VER); }
void presentation(){}
void loop(){}

On boot, the gateway generates the following debug output:

60 MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
118 TSF:LRT:OK
133 TSM:INIT
147 TSF:WUR:MS=0
170 TSM:INIT:TSP OK
191 TSM:INIT:GW MODE
213 TSM:READY:ID=0,PAR=0,DIS=0
246 MCO:REG:NOT NEEDED
scandone
1322 GWT:TIN:CONNECTING...
2350 GWT:TIN:CONNECTING...
scandone
state: 0 -> 2 (b0)
4097 GWT:TIN:CONNECTING...
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt 

connected with Automation, channel 9
dhcp client start...
ip:192.168.1.30,mask:255.255.255.0,gw:192.168.1.193
4316 GWT:TIN:IP: 192.168.1.30
4354 GWT:TIN:ETH OK
4376 MCO:BGN:STP
ESP8266MySensorsGateway version: 0.40
4394 MCO:BGN:INIT OK,TSP=1
4463 TSM:READY:NWD REQ
4490 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
6865 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:208
6933 GWT:TSA:ETH OK

The faux node connects to the gateway indicated by this debug code from the gateway (which is repeated for each "reading" (eg. 204):

1047590 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:204
1047656 GWT:TSA:ETH OK

Nothing arrives at the MQTT broker. From another machine, I can publish to the broker:

mosquitto_pub -h 192.168.1.139 -t test/mztake -m "did it arrive?"

and it does arrive at the broker.

What am I missing?

OSD