Sensebender Micro

[tcontrada]

What is the current consumption of the Sensebender during sleep and active modes?

Thanks,
Tony

[tbowmo]

@tcontrada

there are some measurements in the old design thread here http://forum.mysensors.org/topic/510/minimal-design-thoughts

[nikos1671]

Hi. What case you all using for the sensebender ?Any good idea.

[filipq]

[tbowmo]

@filipq

Where did you find that box?

[filipq]

@tbowmo

Got it from http://cpc.farnell.com/1/1/57932-evatron-pp42m-case-sensor-ivory-71x71x27mm.html.
Not the cheapest, but definitely worth the money as it is very good quality. There are other colours available (white and black) https://www.jprelec.co.uk/store.asp/c=552/Gas-Sensor-Case

[scalz]

@tbowmo: I have some of these too, it's nice box. i got these from tme. cheaper :)
http://www.tme.eu/fr/details/box-sens-white/boitiers-dappar-dalarme-et-de-capt/supertronic/

[ahmedadelhosni]

Hello @tbowmo

Doesn't the atmega328 has only 2 pins which are D2 and D3 from external interrupts ?
I am wondering why do we waste the usage of D2 since the IRQ pin is not used in the library ?

[Anticimex]

@ahmedadelhosni because it is not in use by the library <yet>. Would be a shame if the library some day gets updated with support for a radio that can enter low power sleep and still wake when needed.

[tbowmo]

@ahmedadelhosni

What @Anticimex said.. And at the time when I created the sensebender, I didn't know that the interrupt wasn't used (I was relatively new to the project) so I thought that we had to have it connected..

[hek]

It is used by the RF69, right @tbowmo? (when using adapter plate...)

[ahmedadelhosni]

@Anticimex @tbowmo This a valid point which I thought of but I needed two interrupt pins. As far as I knew from fast searching is that external interrupts which react to CHANGE in pin state are only valid for pins 2 and 3. Correct ?
Maybe there is another solution which I missed.

[tbowmo]

@hek

Yes, that's right, RFM69 is using interrupts.. (and rfm69 is possible on the sensebender using for example this pcb)

[Anticimex]

And with a scalpel and a soldering iron you should be able to use both interrupts by disconnecting the one reserved for nrf24. Of course that would disable the use for rfm69 om that board.

[ahmedadelhosni]

@Anticimex Yeah I could just connect my device to the atmega pin directly as I can see/find any pin header to route the interrupt pin 2. They are all used.

Thanks guys.

[TheoL]

I just received two sensebenders. I'm really impressed by the great engineering behind the board. I can't wait to heat up my soldering iron. I love them!

[user2334]

I just received two Sensebenders, but have problems getting the device to consume little power. I get totally different values as displayed above.

With the following sketch, I get about 5,6mA in active state and 1,6mA in sleep mode with nRF24 attached. I have compared different nRF24-chips and this one consumed the least power.

Without the nRF24, I get 4mA and 0,025mA (=25µA) during sleep mode.

#include <LowPower.h>
#include "RF24.h"

RF24 radio(9, 10);

void setup() {
}

void loop() {
    delay(8000);
    LowPower.powerDown(SLEEP_8S, ADC_OFF, BOD_OFF);
}

[mfalkvidd]

@user2334 I don't think the LowPower library shuts off the radio. Use MySensor's sleep function instead.

[ximinez]

A general question regarding these types of boards that are generally designed to be used on battery power. Is there a reason to not power the ATSH204A and Si7021 from AVR pins? The pins can source far more than what these devices can sink (even when using the heating on the Si7021), and it would allow squeezing a tiny bit more out of the battery life by selectively powering down the devices.
Eg., if I'm not using the ATSHA204A at all, I can save 150nA continuous current. The power saving from disabling the Si7021 is less at about 60nA, so that might just be eaten up by having to wait up to 80ms before a full conversion.

I'm aware that we're talking about saving a tiny ~200nA here, but over the span of two years that adds up to about 350mAh.

So what I'm wondering is simply, is there a technical reason saying that this really isn't a Good Idea (tm)? Should I avoid doing so if I design my own similar device?

[LastSamurai]

@ximinez said:

A general question regarding these types of boards that are generally designed to be used on battery power. Is there a reason to not power the ATSH204A and Si7021 from AVR pins? The pins can source far more than what these devices can sink (even when using the heating on the Si7021), and it would allow squeezing a tiny bit more out of the battery life by selectively powering down the devices.
Eg., if I'm not using the ATSHA204A at all, I can save 150nA continuous current. The power saving from disabling the Si7021 is less at about 60nA, so that might just be eaten up by having to wait up to 80ms before a full conversion.

I'm aware that we're talking about saving a tiny ~200nA here, but over the span of two years that adds up to about 350mAh.

So what I'm wondering is simply, is there a technical reason saying that this really isn't a Good Idea (tm)? Should I avoid doing so if I design my own similar device?

I second that question. I was just thinking about a similar idea.