Sensebender Micro

[bjacobse]

@mvader
Spec is: High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C
So the temp accuracy is quite good

[bjacobse]

@nivoc
Yes you are right, +-3 from your humidity solution on 33%, then the reading could be in the interval 33-3=30% or up to 33+3=36% and should not show 40%

did you get same false readings from other sensebender humidity sensors?

[nivoc]

@bjacobse Yes I have 3 sensbener running from 2 different orders. All 3 are very near by each other. So at 33% they all read something near to 40%.

I have 4 more sensbenders to build. However I continue to test tonight with a Boveda-Pack that claims to bring the hum in a containter to exactly 69%. I did 4 test's so far and also used different technics. So i get more and more confident.

But the very good thing is - it looks every reproducible. So the value may be off but reproducable accurate off by about 8%. When I completed my test it will be very easy to correct it within the software.

[nivoc]

@mvader I haven't made any very accurate temp testings. But the readings are exactly the same than other non-sensbender devices in my home. I started researching the humidity b/c I had different readings between different devices.

Temp looks fine to me.

[tcontrada]

What is the current consumption of the Sensebender during sleep and active modes?

Thanks,
Tony

[tbowmo]

@tcontrada

there are some measurements in the old design thread here http://forum.mysensors.org/topic/510/minimal-design-thoughts

[nikos1671]

Hi. What case you all using for the sensebender ?Any good idea.

[filipq]

[tbowmo]

@filipq

Where did you find that box?

[filipq]

@tbowmo

Got it from http://cpc.farnell.com/1/1/57932-evatron-pp42m-case-sensor-ivory-71x71x27mm.html.
Not the cheapest, but definitely worth the money as it is very good quality. There are other colours available (white and black) https://www.jprelec.co.uk/store.asp/c=552/Gas-Sensor-Case

[scalz]

@tbowmo: I have some of these too, it's nice box. i got these from tme. cheaper :)
http://www.tme.eu/fr/details/box-sens-white/boitiers-dappar-dalarme-et-de-capt/supertronic/

[ahmedadelhosni]

Hello @tbowmo

Doesn't the atmega328 has only 2 pins which are D2 and D3 from external interrupts ?
I am wondering why do we waste the usage of D2 since the IRQ pin is not used in the library ?

[Anticimex]

@ahmedadelhosni because it is not in use by the library <yet>. Would be a shame if the library some day gets updated with support for a radio that can enter low power sleep and still wake when needed.

[tbowmo]

@ahmedadelhosni

What @Anticimex said.. And at the time when I created the sensebender, I didn't know that the interrupt wasn't used (I was relatively new to the project) so I thought that we had to have it connected..

[hek]

It is used by the RF69, right @tbowmo? (when using adapter plate...)

[ahmedadelhosni]

@Anticimex @tbowmo This a valid point which I thought of but I needed two interrupt pins. As far as I knew from fast searching is that external interrupts which react to CHANGE in pin state are only valid for pins 2 and 3. Correct ?
Maybe there is another solution which I missed.

[tbowmo]

@hek

Yes, that's right, RFM69 is using interrupts.. (and rfm69 is possible on the sensebender using for example this pcb)

[Anticimex]

And with a scalpel and a soldering iron you should be able to use both interrupts by disconnecting the one reserved for nrf24. Of course that would disable the use for rfm69 om that board.

[ahmedadelhosni]

@Anticimex Yeah I could just connect my device to the atmega pin directly as I can see/find any pin header to route the interrupt pin 2. They are all used.

Thanks guys.

[TheoL]

I just received two sensebenders. I'm really impressed by the great engineering behind the board. I can't wait to heat up my soldering iron. I love them!