Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensor Moteino Gateway board for Raspberry PI2

lafleur last edited by

I built these for my own use, a PCB that will interface a Moteino, Moteino MEGA or RFM69H(W) to a Raspberry PI2 (its should also work with a B+, but I do not have one for testing)
Board is about 2.1 x 2.75... At this point its still a prototype, not a production board.

I have a few (6) extra board (PCB only) at $8 each with shipping in USA. (contact me direct tom .. at .. lafleur .. us)

Full information with schematics and Gerber files located at:

https://github.com/trlafleur/Moteino-PI2-Gateway.git
Reply Quote 0
1 Reply Last reply

1
Posts

1460
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3281
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

42
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

72
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...

MySensor Moteino Gateway board for Raspberry PI2

Suggested Topics

Over the air updates
General Discussion • • ToSa

Sleep mode for bmp280
Hardware • • fishermans

Arduino Nano Every problem
Hardware • • hakha4

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Which one should i choose? PIR or microwave sensor
Hardware • • h01

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

70
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

MySensor Moteino Gateway board for Raspberry PI2

Suggested Topics

Over the air updates General Discussion • • ToSa

Sleep mode for bmp280 Hardware • • fishermans

Arduino Nano Every problem Hardware • • hakha4

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design" Hardware • • wrendral

Which one should i choose? PIR or microwave sensor Hardware • • h01

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

70Online

11.4kUsers

11.1kTopics

112.7kPosts

Over the air updates
General Discussion • • ToSa

Sleep mode for bmp280
Hardware • • fishermans

Arduino Nano Every problem
Hardware • • hakha4

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Which one should i choose? PIR or microwave sensor
Hardware • • h01

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

70
Online

11.4k
Users

11.1k
Topics

112.7k
Posts